Add first examples

examples/Example2_NetworkInfo/Example2_NetworkInfo.ino

@@ -0,0 +1,123 @@
+#include "SparkFun_u-blox_Cellular_Arduino_Library.h"
+
+// Uncomment the line below that you need for Serial on your platform
+#define mySerial Serial1
+// SoftwareSerial mySerial(16, 17);
+
+// Uncomment the module you're using. If your module is not listed below, then
+// it's not supported for this example
+UBX_CELL myModule; // This example works with all modules, so the base class can be used
+// SARA_R5 myModule; // Base SARA-R5 class
+// SARA_R500S myModule;
+// SARA_R500S_01B myModule;
+// SARA_R500S_61B myModule;
+// SARA_R510M8S_61B myModule;
+// SARA_R510S myModule;
+// LARA_R6 myModule; // Base LARA-R6 class
+// LARA_R6001 myModule;
+// LARA_R6001D myModule;
+// LARA_R6401 myModule;
+// LARA_R6401D myModule;
+// LARA_R6801_00B myModule;
+// LARA_R6801D myModule;
+
+// Map registration status messages to more readable strings
+String registrationString[] =
+{
+  "Not registered",                         // 0
+  "Registered, home",                       // 1
+  "Searching for operator",                 // 2
+  "Registration denied",                    // 3
+  "Registration unknown",                   // 4
+  "Registered, roaming",                    // 5
+  "Registered, home (SMS only)",            // 6
+  "Registered, roaming (SMS only)",         // 7
+  "Registered, emergency service only",     // 8
+  "Registered, home, CSFB not preferred",   // 9
+  "Registered, roaming, CSFB not prefered"  // 10
+};
+
+// If you are based in Europe, you will (probably) need to select MNO_STD_EUROPE
+const mobile_network_operator_t MOBILE_NETWORK_OPERATOR = MNO_GLOBAL;
+
+void setup()
+{
+  Serial.begin(115200); // Start the serial console
+
+  // Wait for user to press key to begin
+  Serial.println(F("u-blox Cellular Example 2 - Network Info"));
+  Serial.println(F("Press any key to begin"));
+
+  while (!Serial.available()) // Wait for the user to press a key (send any serial character)
+    ;
+  while (Serial.available()) // Empty the serial RX buffer
+    Serial.read();
+
+  Serial.println(F("Beginning..."));
+
+  // myModule.enableDebugging(); // Uncomment this line to enable helpful debug messages on Serial
+
+  // For the MicroMod Asset Tracker, we need to invert the power pin so it pulls high instead of low
+  // Uncomment the next line if required
+  // myModule.invertPowerPin(true); 
+
+  // Initialize the module
+  if (myModule.begin(mySerial, UBX_CELL_DEFAULT_BAUD_RATE) )
+  {
+    Serial.println(F("Module connected!"));
+  }
+  else
+  {
+    Serial.println(F("Unable to communicate with the module."));
+    Serial.println(F("Manually power-on (hold the module's On button for 3 seconds) and try again."));
+    while (1) ; // Loop forever on fail
+  }
+  Serial.println();
+
+  if (!myModule.setNetworkProfile(MOBILE_NETWORK_OPERATOR))
+  {
+    Serial.println(F("Error setting network. Try cycling the power."));
+    while (1) ;
+  }
+
+  Serial.println(F("Network profile set. Ready to go!"));
+
+  // RSSI: Received signal strength:
+  Serial.println("RSSI: " + String(myModule.rssi()));
+  // Registration Status
+  int regStatus = myModule.registration();
+  if ((regStatus >= 0) && (regStatus <= 10))
+  {
+    Serial.println("Network registration: " + registrationString[regStatus]);
+  }
+
+  // Print the Context IDs, Access Point Names and IP Addresses
+  Serial.println(F("Available PDP (Packet Data Protocol) APNs (Access Point Names) and IP Addresses:"));
+  Serial.println(F("Context ID:\tAPN Name:\tIP Address:"));
+  for (int cid = 0; cid < UBX_CELL_NUM_PDP_CONTEXT_IDENTIFIERS; cid++)
+  {
+    String apn = "";
+    IPAddress ip(0, 0, 0, 0);
+    myModule.getAPN(cid, &apn, &ip);
+    if (apn.length() > 0)
+    {
+      Serial.print(cid);
+      Serial.print(F("\t\t"));
+      Serial.print(apn);
+      Serial.print(F("\t"));
+      Serial.println(ip);
+    }
+  }
+
+  Serial.println();
+
+  if (regStatus > 0)
+  {
+    Serial.println(F("All set. Go to the next example!"));
+  }
+}
+
+void loop()
+{
+  // Do nothing. Now that we're registered move on to the next example.
+}