v1.0.2

examples/SARA-R5_Example2_Identification_ESPSoftwareSerial/SARA-R5_Example2_Identification_ESPSoftwareSerial.ino

@@ -0,0 +1,139 @@
+/*
+
+  SARA-R5 Example
+  ===============
+
+  Identification - using ESPSoftwareSerial
+
+  Written by: Paul Clark
+  Date: December 29th 2021
+
+  This example demonstrates how to read the SARA's:
+    Manufacturer identification
+    Model identification
+    Firmware version identification
+    Product Serial No.
+    IMEI identification
+    IMSI identification
+    SIM CCID
+    Subscriber number
+    Capabilities
+    SIM state
+
+  The ESP32 core doesn't include SoftwareSerial. Instead we use the library by Peter Lerup and Dirk O. Kaar:
+  https://github.com/plerup/espsoftwareserial
+
+  Feel like supporting open source hardware?
+  Buy a board from SparkFun!
+
+  Licence: MIT
+  Please see LICENSE.md for full details
+
+*/
+
+// Include SoftwareSerial.h _before_ including SparkFun_u-blox_SARA-R5_Arduino_Library.h
+// to allow the SARA-R5 library to detect SoftwareSerial.h using an #if __has_include
+#include <SoftwareSerial.h> //Click here to get the library: http://librarymanager/All#ESPSoftwareSerial_ESP8266/ESP32
+
+#include <SparkFun_u-blox_SARA-R5_Arduino_Library.h> //Click here to get the library: http://librarymanager/All#SparkFun_u-blox_SARA-R5_Arduino_Library
+
+// Create a SoftwareSerial object to pass to the SARA-R5 library
+// Note: we need to call saraSerial.begin and saraSerial.end in setup() - see below for details
+SoftwareSerial saraSerial;
+
+// Create a SARA_R5 object to use throughout the sketch
+// Usually we would tell the library which GPIO pin to use to control the SARA power (see below),
+// but we can start the SARA without a power pin. It just means we need to manually 
+// turn the power on if required! ;-D
+SARA_R5 mySARA;
+
+// Create a SARA_R5 object to use throughout the sketch
+// We need to tell the library what GPIO pin is connected to the SARA power pin.
+// If you're using the MicroMod Asset Tracker and the MicroMod Artemis Processor Board,
+// the pin name is G2 which is connected to pin AD34.
+// Change the pin number if required.
+//SARA_R5 mySARA(34);
+
+// Map SIM states to more readable strings
+String simStateString[] =
+{
+  "Not present",      // 0
+  "PIN needed",       // 1
+  "PIN blocked",      // 2
+  "PUK blocked",      // 3
+  "Not operational",  // 4
+  "Restricted",       // 5
+  "Operational"       // 6
+};
+
+// processSIMstate is provided to the SARA-R5 library via a 
+// callback setter -- setSIMstateReadCallback. (See setup())
+void processSIMstate(SARA_R5_sim_states_t state)
+{
+  Serial.println();
+  Serial.print(F("SIM state:           "));
+  Serial.print(String(state));
+  Serial.println();
+}
+
+void setup()
+{
+  Serial.begin(115200); // Start the serial console
+
+  // Wait for user to press key to begin
+  Serial.println(F("SARA-R5 Example"));
+  Serial.println(F("Press any key to begin"));
+
+  while (!Serial.available()) // Wait for the user to press a key (send any serial character)
+    ;
+  while (Serial.available()) // Empty the serial RX buffer
+    Serial.read();
+
+  //mySARA.enableDebugging(); // Uncomment this line to enable helpful debug messages on Serial
+
+  // For the MicroMod Asset Tracker, we need to invert the power pin so it pulls high instead of low
+  // Comment the next line if required
+  mySARA.invertPowerPin(true);
+
+  // ESPSoftwareSerial does not like repeated .begin's without a .end in between.
+  // We need to .begin and .end the saraSerial port here, before the mySARA.begin, to set up the pin numbers etc.
+  // E.g. to use: 57600 baud; 8 databits, no parity, 1 stop bit; RXD on pin 33; TXD on pin 32; no inversion.
+  Serial.println(F("Configuring SoftwareSerial saraSerial"));
+  saraSerial.begin(57600, SWSERIAL_8N1, 33, 32, false);
+  saraSerial.end();
+
+  // Initialize the SARA
+  if (mySARA.begin(saraSerial, 57600) )
+  {
+    Serial.println(F("SARA-R5 connected!"));
+  }
+  else
+  {
+    Serial.println(F("Unable to communicate with the SARA."));
+    Serial.println(F("Manually power-on (hold the SARA On button for 3 seconds) on and try again."));
+    while (1) ; // Loop forever on fail
+  }
+  Serial.println();
+
+  Serial.println("Manufacturer ID:     " + String(mySARA.getManufacturerID()));
+  Serial.println("Model ID:            " + String(mySARA.getModelID()));
+  Serial.println("Firmware Version:    " + String(mySARA.getFirmwareVersion()));
+  Serial.println("Product Serial No.:  " + String(mySARA.getSerialNo()));
+  Serial.println("IMEI:                " + String(mySARA.getIMEI()));
+  Serial.println("IMSI:                " + String(mySARA.getIMSI()));
+  Serial.println("SIM CCID:            " + String(mySARA.getCCID()));
+  Serial.println("Subscriber No.:      " + String(mySARA.getSubscriberNo()));
+  Serial.println("Capabilities:        " + String(mySARA.getCapabilities()));
+
+  // Set a callback to return the SIM state once requested
+  mySARA.setSIMstateReportCallback(&processSIMstate);
+  // Now enable SIM state reporting for states 0 to 6 (by setting the reporting mode LSb)
+  if (mySARA.setSIMstateReportingMode(1) == SARA_R5_SUCCESS)
+    Serial.println("SIM state reports requested...");
+  // You can disable the SIM staus reports again by calling assetTracker.setSIMstateReportingMode(0)
+}
+
+void loop()
+{
+  mySARA.poll(); // Keep processing data from the SARA so we can extract the SIM status
+}

keywords.txt

@@ -105,6 +105,11 @@ socketWriteUDP	KEYWORD2
 socketRead	KEYWORD2
 socketReadUDP	KEYWORD2
 socketListen	KEYWORD2
+socketDirectLinkMode	KEYWORD2
+socketDirectLinkTimeTrigger	KEYWORD2
+socketDirectLinkDataLengthTrigger	KEYWORD2
+socketDirectLinkCharacterTrigger	KEYWORD2
+socketDirectLinkCongestionTimer	KEYWORD2
 socketGetLastError	KEYWORD2
 lastRemoteIP	KEYWORD2
 ping	KEYWORD2
@@ -122,21 +127,22 @@ sendHTTPPOSTdata	KEYWORD2
 setPDPconfiguration	KEYWORD2
 performPDPaction	KEYWORD2
 activatePDPcontext	KEYWORD2
-boolean isGPSon	KEYWORD2
+isGPSon	KEYWORD2
 gpsPower	KEYWORD2
-gpsEnableClock	KEYWORD2
-gpsGetClock	KEYWORD2
-gpsEnableFix	KEYWORD2
-gpsGetFix	KEYWORD2
-gpsEnablePos	KEYWORD2
-gpsGetPos	KEYWORD2
-gpsEnableSat	KEYWORD2
-gpsGetSat	KEYWORD2
+# gpsEnableClock	KEYWORD2
+# gpsGetClock	KEYWORD2
+# gpsEnableFix	KEYWORD2
+# gpsGetFix	KEYWORD2
+# gpsEnablePos	KEYWORD2
+# gpsGetPos	KEYWORD2
+# gpsEnableSat	KEYWORD2
+# gpsGetSat	KEYWORD2
 gpsEnableRmc	KEYWORD2
 gpsGetRmc	KEYWORD2
-gpsEnableSpeed	KEYWORD2
-gpsGetSpeed	KEYWORD2
+# gpsEnableSpeed	KEYWORD2
+# gpsGetSpeed	KEYWORD2
 gpsRequest	KEYWORD2
+gpsAidingServerConf	KEYWORD2
 getFileContents	KEYWORD2
 functionality	KEYWORD2
 sendCustomCommandWithResponse	KEYWORD2

library.properties

@@ -1,5 +1,5 @@
 name=SparkFun u-blox SARA-R5 Arduino Library
-version=1.0.1
+version=1.0.2
 author=SparkFun Electronics <[email protected]>
 maintainer=SparkFun Electronics <sparkfun.com>
 sentence=Library for the u-blox SARA-R5 LTE-M / NB-IoT modules with secure cloud