v2.0.13

examples/Dead_Reckoning/Example7_setESFAutoAlignment/Example7_setESFAutoAlignment.ino

@@ -0,0 +1,116 @@
+/*
+  By: Nathan Seidle
+  SparkFun Electronics
+  Date: August, 2021
+  License: MIT. See license file for more information but you can
+  basically do whatever you want with this code.
+
+  This example configures the AutoAlignment option for the IMU.
+  The ZED-F9R Integration guide recommends enabling Auto Alignment once
+  the device has been attached to the vehicle's frame.
+  Enabling auto-alignment will cause the the sensor fusion status
+  to begin initialization. After driving around a few turns, the sensors
+  should enter 'Calibrated' state. See example 1 for fusion state or
+  monitor UBX-ESF-STATUS.
+
+  As of writing the ZED-F9R is using HPS v1.2 firmware. Please update using u-center if necessary.
+
+  Feel like supporting open source hardware?
+  Buy a board from SparkFun!
+  ZED-F9R: https://www.sparkfun.com/products/16344
+  ZED-F9R pHat: https://www.sparkfun.com/products/16475
+  NEO-M8U: https://www.sparkfun.com/products/16329
+
+  Hardware Connections:
+  Plug a Qwiic cable into the GPS and a Redboard Qwiic
+  If you don't have a platform with a Qwiic connection use the
+  SparkFun Qwiic Breadboard Jumper (https://www.sparkfun.com/products/17912)
+  Open the serial monitor at 115200 baud to see the output
+
+*/
+
+#include <Wire.h> //Needed for I2C to GPS
+
+#include <SparkFun_u-blox_GNSS_Arduino_Library.h> //http://librarymanager/All#SparkFun_u-blox_GNSS
+SFE_UBLOX_GNSS myGNSS;
+
+void setup()
+{
+  Serial.begin(115200);
+  while (!Serial); //Wait for user to open terminal
+  Serial.println(F("SparkFun u-blox Example"));
+
+  Wire.begin();
+
+  //myGNSS.enableDebugging(); // Uncomment this line to enable debug messages on Serial
+
+  if (myGNSS.begin() == false) //Connect to the u-blox module using Wire port
+  {
+    Serial.println(F("Warning! u-blox GPS did not begin correctly."));
+    Serial.println(F("(This may be because the I2C port is busy with HNR messages.)"));
+  }
+
+  bool esfAutoAlignment = myGNSS.getESFAutoAlignment();
+  Serial.print(F("esfAutoAlignment: "));
+  if (esfAutoAlignment == true)
+    Serial.println(F("True"));
+  else
+    Serial.println(F("False"));
+
+  myGNSS.setESFAutoAlignment(true); //Enable UBX-CFG-ESFALG Automatic IMU-mount Alignment
+
+  myGNSS.setAutoHNRATT(false); //Make sure auto HNR attitude messages are disabled
+  myGNSS.setAutoHNRINS(false); //Make sure auto HNR vehicle dynamics messages are disabled
+  myGNSS.setAutoHNRPVT(false); //Make sure auto HNR PVT messages are disabled
+
+  myGNSS.setI2COutput(COM_TYPE_UBX); //Set the I2C port to output UBX only (turn off NMEA noise)
+  myGNSS.saveConfigSelective(VAL_CFG_SUBSEC_IOPORT); //Save (only) the communications port settings to flash and BBR
+}
+
+void loop()
+{
+  // ESF data is produced at the navigation rate, so by default we'll get fresh data once per second
+  if (myGNSS.getEsfInfo()) // Poll new ESF STATUS data
+  {
+    Serial.print(F("Fusion Mode: "));
+    Serial.print(myGNSS.packetUBXESFSTATUS->data.fusionMode);
+    if (myGNSS.packetUBXESFSTATUS->data.fusionMode == 0)
+      Serial.println(F("  Sensor is initializing..."));
+    else if (myGNSS.packetUBXESFSTATUS->data.fusionMode == 1)
+      Serial.println(F("  Sensor is calibrated!"));
+    else if (myGNSS.packetUBXESFSTATUS->data.fusionMode == 2)
+      Serial.println(F("  Sensor fusion is suspended!"));
+    else if (myGNSS.packetUBXESFSTATUS->data.fusionMode == 3)
+      Serial.println(F("  Sensor fusion is disabled!"));
+  }
+
+  // Poll and print selected HNR data
+  if (myGNSS.getHNRAtt(125) == true) // Request HNR Att data using a 125ms timeout
+  {
+    Serial.print(F("Roll: "));
+    Serial.print(myGNSS.getHNRroll(), 2); // Use the helper function to get the roll in degrees
+    Serial.print(F(" Pitch: "));
+    Serial.print(myGNSS.getHNRpitch(), 2); // Use the helper function to get the pitch in degrees
+    Serial.print(F(" Heading: "));
+    Serial.println(myGNSS.getHNRheading(), 2); // Use the helper function to get the heading in degrees
+  }
+  if (myGNSS.getHNRDyn(125) == true) // Request HNR Dyn data using a 125ms timeout
+  {
+    Serial.print(F("xAccel: "));
+    Serial.print(myGNSS.packetUBXHNRINS->data.xAccel);
+    Serial.print(F(" yAccel: "));
+    Serial.print(myGNSS.packetUBXHNRINS->data.yAccel);
+    Serial.print(F(" zAccel: "));
+    Serial.println(myGNSS.packetUBXHNRINS->data.zAccel);
+  }
+  if (myGNSS.getHNRPVT(125) == true) // Request HNR PVT data using a 125ms timeout
+  {
+    Serial.print(F("ns: "));
+    Serial.print(myGNSS.packetUBXHNRPVT->data.nano);
+    Serial.print(F(" Lat: "));
+    Serial.print(myGNSS.packetUBXHNRPVT->data.lat);
+    Serial.print(F(" Lon: "));
+    Serial.println(myGNSS.packetUBXHNRPVT->data.lon);
+  }
+
+}

examples/Example1_BasicNMEARead/Example1_BasicNMEARead.ino

@@ -23,7 +23,7 @@
 
 #include <Wire.h> //Needed for I2C to GNSS
 
-#include <SparkFun_u-blox_GNSS_Arduino_Library.h> //Click here to get the library: http://librarymanager/All#SparkFun_Ublox_GPS
+#include <SparkFun_u-blox_GNSS_Arduino_Library.h> //Click here to get the library: http://librarymanager/All#SparkFun_u-blox_GNSS
 SFE_UBLOX_GNSS myGNSS;
 
 void setup()