Add Opta support

.github/workflows/compile-examples.yml

@@ -51,6 +51,9 @@ jobs:
           - fqbn: arduino:mbed_portenta:envie_m7
             ethernet: false
             nina: false
+          - fqbn: arduino:mbed_opta:opta
+            ethernet: true
+            nina: false
 
         # Make board type-specific customizations to the matrix jobs
         include:

examples/RTU/ModbusRTUClientParameters/ModbusRTUClientParameters.ino

@@ -0,0 +1,75 @@
+/*
+  Modbus RTU Client Parameters
+
+  This sketch is the same as ModbusRTUClientToggle and shows how to set
+  a few RS485 parameters.
+
+  Circuit:
+   - Arduino Opta
+     - GND connected to GND of the Modbus RTU server
+     - A(-) connected to A of the Modbus RTU server
+     - B(+) connected to B of the Modbus RTU server
+*/
+
+#include <ArduinoRS485.h> // ArduinoModbus depends on the ArduinoRS485 library
+#include <ArduinoModbus.h>
+
+constexpr auto baudrate { 19200 };
+
+// Calculate preDelay and postDelay in microseconds as per Modbus RTU Specification
+//
+// MODBUS over serial line specification and implementation guide V1.02
+// Paragraph 2.5.1.1 MODBUS Message RTU Framing
+// https://modbus.org/docs/Modbus_over_serial_line_V1_02.pdf
+constexpr auto bitduration { 1.f / baudrate };
+constexpr auto wordlen { 9.6f }; // try also with 10.0f
+constexpr auto preDelayBR { bitduration * wordlen * 3.5f * 1e6 };
+constexpr auto postDelayBR { bitduration * wordlen * 3.5f * 1e6 };
+
+void setup() {
+  Serial.begin(9600);
+  while (!Serial);
+
+  Serial.println("Modbus RTU Client Toggle w/ Parameters");
+
+  RS485.setDelays(preDelayBR, postDelayBR);
+
+  // start the Modbus RTU client in 8E1 mode
+  if (!ModbusRTUClient.begin(baudrate, SERIAL_8E1)) {
+    Serial.println("Failed to start Modbus RTU Client!");
+    while (1);
+  }
+}
+
+void loop() {
+  // for (slave) id 1: write the value of 0x01, to the coil at address 0x00 
+  if (!ModbusRTUClient.coilWrite(1, 0x00, 0x01)) {
+    Serial.print("Failed to write coil! ");
+    Serial.println(ModbusRTUClient.lastError());
+  }
+
+  // wait for 0.5 second
+  delay(500);
+
+  // for (slave) id 1: write the value of 0x00, to the coil at address 0x00 
+  if (!ModbusRTUClient.coilWrite(1, 0x00, 0x00)) {
+    Serial.print("Failed to write coil! ");
+    Serial.println(ModbusRTUClient.lastError());
+  }
+
+  // wait for 0.5 second
+  delay(500);
+
+  auto coil = ModbusRTUClient.coilRead(0x02, 0x00);
+
+  if (coil < 0) {
+    Serial.print("Failed to read coil: ");
+    Serial.println(ModbusRTUClient.lastError());
+  } else {
+    Serial.print("Coil: ");
+      Serial.println(coil);
+  }
+
+  // wait for 0.5 second
+  delay(500); 
+}

library.properties

@@ -6,6 +6,6 @@ sentence=Use Modbus equipment with your Arduino.
 paragraph=Using TCP or RS485 shields, like the MKR 485 Shield. This library depends on the ArduinoRS485 library.
 category=Communication
 url=https://www.arduino.cc/en/ArduinoModbus/ArduinoModbus
-architectures=megaavr,samd,mbed_nano,mbed_portenta
+architectures=megaavr,samd,mbed_nano,mbed_portenta,mbed_opta
 includes=ArduinoModbus.h
 depends=ArduinoRS485