Removed powerUp. No longer needed.

Author: henrikekblad

libraries/MySensors/examples/BatteryPoweredSensor/BatteryPoweredSensor.ino

@@ -49,7 +49,6 @@ void loop()
 
    if (oldBatteryPcnt != batteryPcnt) {
      // Power up radio after sleep
-     gw.powerUp();
      gw.sendBatteryLevel(batteryPcnt);
      oldBatteryPcnt = batteryPcnt;
    }

libraries/MySensors/examples/DallasTemperatureSensor/DallasTemperatureSensor.ino

@@ -37,7 +37,6 @@ void setup()
 
 void loop()     
 {     
-  gw.powerUp();
   sensors.requestTemperatures(); // Fetch temperatures from Dallas
   delay(100);
   for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {

libraries/MySensors/examples/DistanceSensor/DistanceSensor.ino

@@ -31,7 +31,6 @@ void setup()
 
 void loop()      
 {     
-  gw.powerUp(); // Power up radio
   int dist = metric?sonar.ping_cm():sonar.ping_in();
 
   Serial.print("Ping: ");

libraries/MySensors/examples/EnergyMeterPulseSensor/EnergyMeterPulseSensor.ino

@@ -59,8 +59,6 @@ void loop()
    unsigned long now = millis();
   // Only send values at a maximum frequency or woken up from sleep
   if (SLEEP_MODE || now - lastSend > 1000*SEND_FREQUENCY) {
-    gw.powerUp(); // Power up radio
-
     // New watt value has been calculated  
     if (!SLEEP_MODE && watt != oldWatt) {
       // Check that we dont get unresonable large watt value. 

libraries/MySensors/examples/HumiditySensor/HumiditySensor.ino

@@ -34,7 +34,6 @@ void setup()
 
 void loop()      
 {  
-  gw.powerUp(); // Power up radio
   delay(dht.getMinimumSamplingPeriod());
 
   float temperature = dht.getTemperature();

libraries/MySensors/examples/LightLuxSensor/LightLuxSensor.ino

@@ -49,8 +49,6 @@ void setup()
 
 void loop()      
 {     
-  gw.powerUp(); // Power up radio (after sleep)
-
   uint16_t lux = lightSensor.readLightLevel();// Get Lux value
   Serial.println(lux);
   if (lux != lastlux) {

libraries/MySensors/examples/LightSensor/LightSensor.ino

@@ -26,8 +26,6 @@ void setup()
 
 void loop()      
 {     
-  gw.powerUp(); // Power up radio (after sleep)
-
   int lightLevel = (1023-analogRead(LIGHT_SENSOR_ANALOG_PIN))/10.23; 
   Serial.println(lightLevel);
   if (lightLevel != lastLightLevel) {

libraries/MySensors/examples/MotionSensor/MotionSensor.ino

@@ -13,6 +13,8 @@ Sleep sleep;
 
 void setup()  
 {  
+  EEPROM.write(EEPROM_RELAY_ID_ADDRESS, 0);
+  
   gw.begin();
 
   // Send the sketch version information to the gateway and Controller
@@ -25,7 +27,6 @@ void setup()
 
 void loop()     
 {     
-  gw.powerUp(); // Power up radio
   // Read digital motion value
   boolean tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH; 
 

libraries/MySensors/examples/PressureSensor/PressureSensor.ino

@@ -44,8 +44,6 @@ void setup() {
 
 
 void loop() {
-  gw.powerUp(); // Power up radio
-
   float pressure = bmp.readPressure();
   float temperature = bmp.readTemperature();
 

libraries/MySensors/examples/SoilMoistSensor/SoilMoistSensor.ino

@@ -26,7 +26,6 @@ void setup()
 
 void loop()     
 {     
-  gw.powerUp(); // Power up radio
   // Read digital soil value
   int soilValue = digitalRead(DIGITAL_INPUT_SOIL_SENSOR); // 1 = Not triggered, 0 = In soil with water 
   if (soilValue != lastSoilValue) {

libraries/MySensors/examples/WaterMeterPulseSensor/WaterMeterPulseSensor.ino

@@ -69,8 +69,6 @@ void loop()
 
     // Only send values at a maximum frequency or woken up from sleep
   if (SLEEP_MODE || currentTime - lastSend > 1000*SEND_FREQUENCY) {
-    gw.powerUp(); // Power up radio
-    
     // New flow value has been calculated  
     if (!SLEEP_MODE && flow != oldflow) {
       // Check that we dont get unresonable large flow value.