Merge branch 'espressif:master' into work

Author: Jason2866

Diff for: cores/esp32/esp32-hal-gpio.h

@@ -49,13 +49,6 @@ extern "C" {
 #define INPUT_PULLDOWN    0x09
 #define OPEN_DRAIN        0x10
 #define OUTPUT_OPEN_DRAIN 0x12
-#define SPECIAL           0xF0
-#define FUNCTION_1        0x00
-#define FUNCTION_2        0x20
-#define FUNCTION_3        0x40
-#define FUNCTION_4        0x60
-#define FUNCTION_5        0x80
-#define FUNCTION_6        0xA0
 #define ANALOG            0xC0
 
 //Interrupt Modes

Diff for: libraries/Ethernet/src/ETH.cpp

@@ -123,7 +123,7 @@ static esp_err_t on_lowlevel_init_done(esp_eth_handle_t eth_handle){
         //gpio_hal_iomux_func_sel(PERIPHS_IO_MUX_GPIO0_U, FUNC_GPIO0_EMAC_TX_CLK);
         //PIN_INPUT_ENABLE(GPIO_PIN_MUX_REG[0]);
         pinMode(0, INPUT);
-        pinMode(0, FUNCTION_6);
+        PIN_FUNC_SELECT(GPIO_PIN_MUX_REG[0], 5);
         EMAC_EXT.ex_clk_ctrl.ext_en = 1;
         EMAC_EXT.ex_clk_ctrl.int_en = 0;
         EMAC_EXT.ex_oscclk_conf.clk_sel = 1;
@@ -135,7 +135,7 @@ static esp_err_t on_lowlevel_init_done(esp_eth_handle_t eth_handle){
             //gpio_hal_iomux_func_sel(PERIPHS_IO_MUX_GPIO0_U, FUNC_GPIO0_CLK_OUT1);
             //PIN_INPUT_DISABLE(GPIO_PIN_MUX_REG[0]);
             pinMode(0, OUTPUT);
-            pinMode(0, FUNCTION_2);
+            PIN_FUNC_SELECT(GPIO_PIN_MUX_REG[0], 1);
             // Choose the APLL clock to output on GPIO
             REG_WRITE(PIN_CTRL, 6);
 #endif
@@ -145,15 +145,15 @@ static esp_err_t on_lowlevel_init_done(esp_eth_handle_t eth_handle){
             //gpio_hal_iomux_func_sel(PERIPHS_IO_MUX_GPIO16_U, FUNC_GPIO16_EMAC_CLK_OUT);
             //PIN_INPUT_DISABLE(GPIO_PIN_MUX_REG[16]);
             pinMode(16, OUTPUT);
-            pinMode(16, FUNCTION_6);
+            PIN_FUNC_SELECT(GPIO_PIN_MUX_REG[16], 5);
 #endif
         } else if(eth_clock_mode == ETH_CLOCK_GPIO17_OUT){
 #if CONFIG_ETH_RMII_CLK_OUT_GPIO != 17
             // RMII CLK (50MHz) output to GPIO17
             //gpio_hal_iomux_func_sel(PERIPHS_IO_MUX_GPIO17_U, FUNC_GPIO17_EMAC_CLK_OUT_180);
             //PIN_INPUT_DISABLE(GPIO_PIN_MUX_REG[17]);
             pinMode(17, OUTPUT);
-            pinMode(17, FUNCTION_6);
+            PIN_FUNC_SELECT(GPIO_PIN_MUX_REG[17], 5);
 #endif
         }
 #if CONFIG_ETH_RMII_CLK_INPUT

Diff for: platform.txt

@@ -246,4 +246,9 @@ tools.esptool_py.upload.network_pattern={network_cmd} -i "{serial.port}" -p "{ne
 ## Upload Sketch Through OTA (Arduino IDE 2.x)
 ## -------------------------------------------
 tools.esp_ota.upload.protocol=network
-tools.esp_ota.upload.pattern={cmd} -i "{upload.port.address}" -p "{upload.port.properties.port}" "--auth={upload.field.password}" -f "{build.path}/{build.project_name}.bin"
+## Following command does not work currently, because port properties are lost and auth dialog does not permit empty fields
+#tools.esp_ota.upload.field.password=Password
+#tools.esp_ota.upload.field.password.secret=true
+#tools.esp_ota.upload.pattern={cmd} -i "{upload.port.address}" -p "{upload.port.properties.port}" "--auth={upload.field.password}" -f "{build.path}/{build.project_name}.bin"
+## So we do basic default OTA on port 3232 and no auth
+tools.esp_ota.upload.pattern={cmd} -i "{upload.port.address}" -f "{build.path}/{build.project_name}.bin"