diff --git a/README.md b/README.md index 60461a114d..8129fc03a7 100644 --- a/README.md +++ b/README.md @@ -101,8 +101,9 @@ User can add a STM32 based board following this [wiki](https://github.com/stm32d | :---: | --- | :---: | :--- | | :green_heart: | [BluePill F103C(6-8-B)](https://stm32-base.org/boards/STM32F103C8T6-Blue-Pill) | *1.2.0* | USB CDC support since *1.5.0*, Maple bootloaders support since *1.6.0* | | :green_heart: | [BlackPill F103C(8-B)](https://stm32-base.org/boards/STM32F103C8T6-Black-Pill) | *1.5.0* | | -| :green_heart: | MapleMini F103CB | *1.2.0* | USB CDC support since *1.5.0*, Maple bootloaders support since *1.6.0* | +| :yellow_heart: | [Generic F103R(8-B-C-E)T6](https://stm32-base.org/boards/STM32F103RET6-Generic-Board) | **1.7.0** | Blue Button | | :green_heart: | HY-TinySTM103T | *1.5.0* | | +| :green_heart: | MapleMini F103CB | *1.2.0* | USB CDC support since *1.5.0*, Maple bootloaders support since *1.6.0* | | Status | Generic STM32F3xx | Release | Comment | | :---: | --- | :---: | :--- | diff --git a/boards.txt b/boards.txt index 8b8ee5032f..5201a8591a 100644 --- a/boards.txt +++ b/boards.txt @@ -729,13 +729,34 @@ GenF1.menu.pnum.BLACKPILL_F103C8B.build.board=BLACKPILL_F103C8 GenF1.menu.pnum.BLACKPILL_F103C8B.build.product_line=STM32F103xB GenF1.menu.pnum.BLACKPILL_F103C8B.build.variant=PILL_F103XX -# MAPLEMINI_F103CB board -GenF1.menu.pnum.MAPLEMINI_F103CB=Maple Mini F103CB -GenF1.menu.pnum.MAPLEMINI_F103CB.upload.maximum_size=131072 -GenF1.menu.pnum.MAPLEMINI_F103CB.upload.maximum_data_size=20480 -GenF1.menu.pnum.MAPLEMINI_F103CB.build.board=MAPLEMINI_F103CB -GenF1.menu.pnum.MAPLEMINI_F103CB.build.product_line=STM32F103xB -GenF1.menu.pnum.MAPLEMINI_F103CB.build.variant=MAPLEMINI_F103CB +# Generic STM32F103Rx boards (Blue button) +GenF1.menu.pnum.Generic_F103R8T6=Generic F103R8T6 (Blue Button) +GenF1.menu.pnum.Generic_F103R8T6.upload.maximum_size=65536 +GenF1.menu.pnum.Generic_F103R8T6.upload.maximum_data_size=20480 +GenF1.menu.pnum.Generic_F103R8T6.build.board=GENERIC_F103R8T6 +GenF1.menu.pnum.Generic_F103R8T6.build.product_line=STM32F103xB +GenF1.menu.pnum.Generic_F103R8T6.build.variant=Generic_F103Rx + +GenF1.menu.pnum.Generic_F103RBT6=Generic F103RBT6 (Blue Button) +GenF1.menu.pnum.Generic_F103RBT6.upload.maximum_size=131072 +GenF1.menu.pnum.Generic_F103RBT6.upload.maximum_data_size=20480 +GenF1.menu.pnum.Generic_F103RBT6.build.board=GENERIC_F103RBT6 +GenF1.menu.pnum.Generic_F103RBT6.build.product_line=STM32F103xB +GenF1.menu.pnum.Generic_F103RBT6.build.variant=Generic_F103Rx + +GenF1.menu.pnum.Generic_F103RCT6=Generic F103RCT6 (Blue Button) +GenF1.menu.pnum.Generic_F103RCT6.upload.maximum_size=262144 +GenF1.menu.pnum.Generic_F103RCT6.upload.maximum_data_size=49152 +GenF1.menu.pnum.Generic_F103RCT6.build.board=GENERIC_F103RCT6 +GenF1.menu.pnum.Generic_F103RCT6.build.product_line=STM32F103xE +GenF1.menu.pnum.Generic_F103RCT6.build.variant=Generic_F103Rx + +GenF1.menu.pnum.Generic_F103RET6=Generic F103RET6 (Blue Button) +GenF1.menu.pnum.Generic_F103RET6.upload.maximum_size=524288 +GenF1.menu.pnum.Generic_F103RET6.upload.maximum_data_size=65536 +GenF1.menu.pnum.Generic_F103RET6.build.board=GENERIC_F103RET6 +GenF1.menu.pnum.Generic_F103RET6.build.product_line=STM32F103xE +GenF1.menu.pnum.Generic_F103RET6.build.variant=Generic_F103Rx # HY-TinySTM103TB board GenF1.menu.pnum.HY_TinySTM103TB=HY-TinySTM103TB @@ -745,6 +766,14 @@ GenF1.menu.pnum.HY_TinySTM103TB.build.board=HY_TinySTM103TB GenF1.menu.pnum.HY_TinySTM103TB.build.product_line=STM32F103xB GenF1.menu.pnum.HY_TinySTM103TB.build.variant=HY_TinySTM103T +# MAPLEMINI_F103CB board +GenF1.menu.pnum.MAPLEMINI_F103CB=Maple Mini F103CB +GenF1.menu.pnum.MAPLEMINI_F103CB.upload.maximum_size=131072 +GenF1.menu.pnum.MAPLEMINI_F103CB.upload.maximum_data_size=20480 +GenF1.menu.pnum.MAPLEMINI_F103CB.build.board=MAPLEMINI_F103CB +GenF1.menu.pnum.MAPLEMINI_F103CB.build.product_line=STM32F103xB +GenF1.menu.pnum.MAPLEMINI_F103CB.build.variant=MAPLEMINI_F103CB + # Upload menu GenF1.menu.upload_method.swdMethod=STM32CubeProgrammer (SWD) GenF1.menu.upload_method.swdMethod.upload.protocol=0 diff --git a/variants/Generic_F103Rx/PeripheralPins.c b/variants/Generic_F103Rx/PeripheralPins.c new file mode 100644 index 0000000000..459d39f5e2 --- /dev/null +++ b/variants/Generic_F103Rx/PeripheralPins.c @@ -0,0 +1,375 @@ +/* + ******************************************************************************* + * Copyright (c) 2019, STMicroelectronics + * All rights reserved. + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ******************************************************************************* + * Automatically generated from STM32F103R(8-B)Tx.xml and STM32F103R(C-D-E)Tx.xml + */ +#include "Arduino.h" +#include "PeripheralPins.h" + +/* ===== + * Note: Commented lines are alternative possibilities which are not used per default. + * If you change them, you will have to know what you do + * ===== + */ + +//*** ADC *** + +#ifdef HAL_ADC_MODULE_ENABLED +WEAK const PinMap PinMap_ADC[] = { + {PA_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0 + // {PA_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC2_IN0 +#ifdef STM32F103xE + // {PA_0, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC3_IN0 +#endif + {PA_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1 + // {PA_1, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC2_IN1 +#ifdef STM32F103xE + // {PA_1, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC3_IN1 +#endif + // {PA_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2 + {PA_2, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC2_IN2 +#ifdef STM32F103xE + // {PA_2, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC3_IN2 +#endif +#ifndef STM32F103xE + // {PA_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3 + {PA_3, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC2_IN3 +#else + {PA_3, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC3_IN3 +#endif + // {PA_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4 + {PA_4, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC2_IN4 + {PA_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5 + // {PA_5, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC2_IN5 + // {PA_6, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6 + {PA_6, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC2_IN6 + {PA_7, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 + // {PA_7, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC2_IN7 + // {PB_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8 + {PB_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC2_IN8 + {PB_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9 + // {PB_1, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC2_IN9 + // {PC_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10 + {PC_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC2_IN10 +#ifdef STM32F103xE + // {PC_0, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC3_IN10 +#endif + {PC_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11 + // {PC_1, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC2_IN11 +#ifdef STM32F103xE + // {PC_1, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC3_IN11 +#endif + // {PC_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12 + {PC_2, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC2_IN12 +#ifdef STM32F103xE + // {PC_2, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC3_IN12 +#endif +#ifndef STM32F103xE + {PC_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13 + // {PC_3, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC2_IN13 +#else + {PC_3, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC3_IN13 +#endif + // {PC_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14 + {PC_4, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC2_IN14 + {PC_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15 + // {PC_5, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC2_IN15 + {NC, NP, 0} +}; +#endif + +//*** DAC *** +#ifdef STM32F103xE +#ifdef HAL_DAC_MODULE_ENABLED +WEAK const PinMap PinMap_DAC[] = { + {PA_4, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // DAC_OUT1 + {PA_5, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // DAC_OUT2 + {NC, NP, 0} +}; +#endif +#endif + +//*** I2C *** + +#ifdef HAL_I2C_MODULE_ENABLED +WEAK const PinMap PinMap_I2C_SDA[] = { + {PB_7, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, AFIO_NONE)}, + {PB_9, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, AFIO_I2C1_ENABLE)}, + {PB_11, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, AFIO_NONE)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_I2C_MODULE_ENABLED +WEAK const PinMap PinMap_I2C_SCL[] = { + {PB_6, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, AFIO_NONE)}, + {PB_8, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, AFIO_I2C1_ENABLE)}, + {PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, AFIO_NONE)}, + {NC, NP, 0} +}; +#endif + +//*** PWM *** + +#ifdef HAL_TIM_MODULE_ENABLED +WEAK const PinMap PinMap_PWM[] = { + {PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM2_CH1 + // {PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_2, 1, 0)}, // TIM2_CH1 +#ifdef STM32F103xE + // {PA_0, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM5_CH1 +#endif + {PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM2_CH2 + // {PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_2, 2, 0)}, // TIM2_CH2 +#ifdef STM32F103xE + // {PA_1, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM5_CH2 +#endif + {PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM2_CH3 + // {PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_1, 3, 0)}, // TIM2_CH3 +#ifdef STM32F103xE + // {PA_2, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM5_CH3 +#endif +#ifndef STM32F103xE + {PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM2_CH4 + // {PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_1, 4, 0)}, // TIM2_CH4 +#else + {PA_3, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM5_CH4 +#endif + {PA_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM3_CH1 +#ifndef STM32F103xE + {PA_7, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 1, 1)}, // TIM1_CH1N + // {PA_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM3_CH2 +#else + {PA_7, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 1)}, // TIM8_CH1N +#endif + {PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM1_CH1 + // {PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 1, 0)}, // TIM1_CH1 + {PA_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM1_CH2 + // {PA_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 2, 0)}, // TIM1_CH2 + {PA_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM1_CH3 + // {PA_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 3, 0)}, // TIM1_CH3 + {PA_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM1_CH4 + // {PA_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 4, 0)}, // TIM1_CH4 + {PA_15, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_1, 1, 0)}, // TIM2_CH1 + // {PA_15, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_ENABLE, 1, 0)}, // TIM2_CH1 + // {PB_0, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 2, 1)}, // TIM1_CH2N + // {PB_0, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM3_CH3 + {PB_0, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_PARTIAL, 3, 0)}, // TIM3_CH3 +#ifdef STM32F103xE + // {PB_0, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 1)}, // TIM8_CH2N +#endif + {PB_1, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM1_PARTIAL, 3, 1)}, // TIM1_CH3N + // {PB_1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM3_CH4 + // {PB_1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_PARTIAL, 4, 0)}, // TIM3_CH4 +#ifdef STM32F103xE + // {PB_1, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 1)}, // TIM8_CH3N +#endif + {PB_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_1, 2, 0)}, // TIM2_CH2 + // {PB_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_ENABLE, 2, 0)}, // TIM2_CH2 + {PB_4, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_PARTIAL, 1, 0)}, // TIM3_CH1 + {PB_5, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_PARTIAL, 2, 0)}, // TIM3_CH2 + {PB_6, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM4_CH1 + {PB_7, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM4_CH2 + {PB_8, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM4_CH3 + {PB_9, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM4_CH4 + {PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_2, 3, 0)}, // TIM2_CH3 + // {PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_ENABLE, 3, 0)}, // TIM2_CH3 + {PB_11, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_PARTIAL_2, 4, 0)}, // TIM2_CH4 + // {PB_11, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM2_ENABLE, 4, 0)}, // TIM2_CH4 + {PB_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 1)}, // TIM1_CH1N + {PB_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 1)}, // TIM1_CH2N + {PB_15, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 1)}, // TIM1_CH3N + {PC_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_ENABLE, 1, 0)}, // TIM3_CH1 +#ifdef STM32F103xE + // {PC_6, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 1, 0)}, // TIM8_CH1 +#endif + {PC_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_ENABLE, 2, 0)}, // TIM3_CH2 +#ifdef STM32F103xE + // {PC_7, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 2, 0)}, // TIM8_CH2 +#endif +#ifndef STM32F103xE + {PC_8, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_ENABLE, 3, 0)}, // TIM3_CH3 +#else + {PC_8, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 3, 0)}, // TIM8_CH3 +#endif + {PC_9, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_TIM3_ENABLE, 4, 0)}, // TIM3_CH4 +#ifdef STM32F103xE + // {PC_9, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE, 4, 0)}, // TIM8_CH4 +#endif + {NC, NP, 0} +}; +#endif + +//*** SERIAL *** + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_TX[] = { + {PA_2, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PA_9, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PB_6, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_USART1_ENABLE)}, + {PB_10, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, +#ifdef STM32F103xE + {PC_10, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, +#else + {PC_10, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_USART3_PARTIAL)}, +#endif +#ifdef STM32F103xE + {PC_12, UART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, +#endif + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_RX[] = { + {PA_3, USART2, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_NONE)}, + {PA_10, USART1, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_NONE)}, + {PB_7, USART1, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_USART1_ENABLE)}, + {PB_11, USART3, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_NONE)}, +#ifdef STM32F103xE + {PC_11, UART4, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_NONE)}, +#else + {PC_11, USART3, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_USART3_PARTIAL)}, +#endif +#ifdef STM32F103xE + {PD_2, UART5, STM_PIN_DATA(STM_MODE_INPUT, GPIO_PULLUP, AFIO_NONE)}, +#endif + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_RTS[] = { + {PA_1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PA_12, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PB_14, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PB_14, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_USART3_PARTIAL)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_CTS[] = { + {PA_0, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PA_11, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PB_13, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {PB_13, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_USART3_PARTIAL)}, + {NC, NP, 0} +}; +#endif + +//*** SPI *** + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_MOSI[] = { + {PA_7, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, +#ifndef STM32F103xE + {PB_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_SPI1_ENABLE)}, +#else + {PB_5, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, +#endif + {PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_MISO[] = { + {PA_6, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, +#ifndef STM32F103xE + {PB_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_SPI1_ENABLE)}, +#else + {PB_4, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, +#endif + {PB_14, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_SCLK[] = { + {PA_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, +#ifndef STM32F103xE + {PB_3, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_SPI1_ENABLE)}, +#else + {PB_3, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, +#endif + {PB_13, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_SSEL[] = { + {PA_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, +#ifndef STM32F103xE + {PA_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_SPI1_ENABLE)}, +#else + {PA_15, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, +#endif + {PB_12, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, + {NC, NP, 0} +}; +#endif + +//*** CAN *** + +#ifdef HAL_CAN_MODULE_ENABLED +WEAK const PinMap PinMap_CAN_RD[] = { + {PA_11, CAN1, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, AFIO_NONE)}, + {PB_8, CAN1, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, AFIO_CAN1_2)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_CAN_MODULE_ENABLED +WEAK const PinMap PinMap_CAN_TD[] = { + {PA_12, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, AFIO_NONE)}, + {PB_9, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, AFIO_CAN1_2)}, + {NC, NP, 0} +}; +#endif + +//*** No ETHERNET *** + +//*** No QUADSPI *** + +//*** USB *** + +#ifdef HAL_PCD_MODULE_ENABLED +WEAK const PinMap PinMap_USB[] = { + {PA_11, USB, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, AFIO_NONE)}, // USB_DM + {PA_12, USB, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, AFIO_NONE)}, // USB_DP + {NC, NP, 0} +}; +#endif + +//*** No USB_OTG_FS *** + +//*** No USB_OTG_HS *** + +//*** SD *** +#ifdef STM32F103xE +#ifdef HAL_SD_MODULE_ENABLED +WEAK const PinMap PinMap_SD[] = { + {PB_8, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D4 + {PB_9, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D5 + {PC_6, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D6 + {PC_7, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D7 + {PC_8, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D0 + {PC_9, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D1 + {PC_10, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D2 + {PC_11, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, AFIO_NONE)}, // SDIO_D3 + {PC_12, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, AFIO_NONE)}, // SDIO_CK + {PD_2, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, AFIO_NONE)}, // SDIO_CMD + {NC, NP, 0} +}; +#endif +#endif diff --git a/variants/Generic_F103Rx/PinNamesVar.h b/variants/Generic_F103Rx/PinNamesVar.h new file mode 100644 index 0000000000..2ab6270d8d --- /dev/null +++ b/variants/Generic_F103Rx/PinNamesVar.h @@ -0,0 +1,30 @@ +/* SYS_WKUP */ +#ifdef PWR_WAKEUP_PIN1 +SYS_WKUP1 = PA_0, +#endif +#ifdef PWR_WAKEUP_PIN2 +SYS_WKUP2 = NC, +#endif +#ifdef PWR_WAKEUP_PIN3 +SYS_WKUP3 = NC, +#endif +#ifdef PWR_WAKEUP_PIN4 +SYS_WKUP4 = NC, +#endif +#ifdef PWR_WAKEUP_PIN5 +SYS_WKUP5 = NC, +#endif +#ifdef PWR_WAKEUP_PIN6 +SYS_WKUP6 = NC, +#endif +#ifdef PWR_WAKEUP_PIN7 +SYS_WKUP7 = NC, +#endif +#ifdef PWR_WAKEUP_PIN8 +SYS_WKUP8 = NC, +#endif +/* USB */ +#ifdef USBCON +USB_DM = PA_11, +USB_DP = PA_12, +#endif \ No newline at end of file diff --git a/variants/Generic_F103Rx/ldscript.ld b/variants/Generic_F103Rx/ldscript.ld new file mode 100644 index 0000000000..80bb1d2bb7 --- /dev/null +++ b/variants/Generic_F103Rx/ldscript.ld @@ -0,0 +1,200 @@ +/* +****************************************************************************** +** + +** File : LinkerScript.ld +** +** Author : Auto-generated by STM32CubeIDE +** +** Abstract : Linker script for STM32F103R(8/B/C/ETx Device from STM32F1 series +** 64/128/256/512Kbytes FLASH +** 20/20/48/64Kbytes RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** Distribution: The file is distributed as is without any warranty +** of any kind. +** +***************************************************************************** +** @attention +** +**

© COPYRIGHT(c) 2019 STMicroelectronics

+** +** Redistribution and use in source and binary forms, with or without modification, +** are permitted provided that the following conditions are met: +** 1. Redistributions of source code must retain the above copyright notice, +** this list of conditions and the following disclaimer. +** 2. Redistributions in binary form must reproduce the above copyright notice, +** this list of conditions and the following disclaimer in the documentation +** and/or other materials provided with the distribution. +** 3. Neither the name of STMicroelectronics nor the names of its contributors +** may be used to endorse or promote products derived from this software +** without specific prior written permission. +** +** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE +** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE +** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE +** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL +** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR +** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER +** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, +** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE +** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20000000 + LD_MAX_DATA_SIZE; /* end of "RAM" Ram type memory */ +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x400; /* required amount of stack */ + +/* Memories definition */ +MEMORY +{ + RAM (xrw) : ORIGIN = 0x20000000, LENGTH = LD_MAX_DATA_SIZE + FLASH (rx) : ORIGIN = 0x8000000 + LD_FLASH_OFFSET, LENGTH = LD_MAX_SIZE - LD_FLASH_OFFSET +} + +/* Sections */ +SECTIONS +{ + /* The startup code into "FLASH" Rom type memory */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data into "FLASH" Rom type memory */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data into "FLASH" Rom type memory */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { + . = ALIGN(4); + *(.ARM.extab* .gnu.linkonce.armextab.*) + . = ALIGN(4); + } >FLASH + .ARM : { + . = ALIGN(4); + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + . = ALIGN(4); + } >FLASH + + .preinit_array : + { + . = ALIGN(4); + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + . = ALIGN(4); + } >FLASH + .init_array : + { + . = ALIGN(4); + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + . = ALIGN(4); + } >FLASH + .fini_array : + { + . = ALIGN(4); + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + . = ALIGN(4); + } >FLASH + + /* Used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections into "RAM" Ram type memory */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + + /* Uninitialized data section into "RAM" Ram type memory */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + + + /* Remove information from the compiler libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} + diff --git a/variants/Generic_F103Rx/variant.cpp b/variants/Generic_F103Rx/variant.cpp new file mode 100644 index 0000000000..d5019427e5 --- /dev/null +++ b/variants/Generic_F103Rx/variant.cpp @@ -0,0 +1,132 @@ +/* + Copyright (c) 2011 Arduino. All right reserved. + + This library is free software; you can redistribute it and/or + modify it under the terms of the GNU Lesser General Public + License as published by the Free Software Foundation; either + version 2.1 of the License, or (at your option) any later version. + + This library is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. + See the GNU Lesser General Public License for more details. + + You should have received a copy of the GNU Lesser General Public + License along with this library; if not, write to the Free Software + Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +*/ + +#include "pins_arduino.h" + +#ifdef __cplusplus +extern "C" { +#endif + +const PinName digitalPin[] = { + PA_8, + PA_9, // RXD + PA_10, // TXD + PA_11, // USB D- + PA_12, // USB D+ + PA_13, // JTDI + PA_14, // JTCK + PA_15, + PB_2, + PB_3, // JTDO + PB_4, // JTRST + PB_5, + PB_6, + PB_7, + PB_8, + PB_9, + PB_10, + PB_11, // LED + PB_12, + PB_13, + PB_14, + PB_15, + PC_6, + PC_7, + PC_8, + PC_9, + PC_10, + PC_11, + PC_12, + PC_13, + NC, // PC_14 OSC32_1 + NC, // PC_15 OSC32_2 + NC, // PD_0 OSCIN + NC, // PD_1 OSCOUT + PD_2, + + PA_0, + PA_1, + PA_2, + PA_3, + PA_4, + PA_5, + PA_6, + PA_7, + PB_0, + PB_1, + PC_0, + PC_1, + PC_2, + PC_3, + PC_4, + PC_5 +}; + +#ifdef __cplusplus +} +#endif + +// ---------------------------------------------------------------------------- + +#ifdef __cplusplus +extern "C" { +#endif + +/** + * @brief System Clock Configuration + * @param None + * @retval None + */ +WEAK void SystemClock_Config(void) +{ + RCC_OscInitTypeDef RCC_OscInitStruct = {}; + RCC_ClkInitTypeDef RCC_ClkInitStruct = {}; + RCC_PeriphCLKInitTypeDef PeriphClkInit = {}; + + /* Initializes the CPU, AHB and APB busses clocks */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1; + RCC_OscInitStruct.HSIState = RCC_HSI_ON; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL9; + if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) { + Error_Handler(); + } + /* Initializes the CPU, AHB and APB busses clocks */ + RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK + | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2; + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; + + if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK) { + Error_Handler(); + } + PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USB; + PeriphClkInit.UsbClockSelection = RCC_USBCLKSOURCE_PLL_DIV1_5; + if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK) { + Error_Handler(); + } +} + +#ifdef __cplusplus +} +#endif diff --git a/variants/Generic_F103Rx/variant.h b/variants/Generic_F103Rx/variant.h new file mode 100644 index 0000000000..ac295be41b --- /dev/null +++ b/variants/Generic_F103Rx/variant.h @@ -0,0 +1,144 @@ +/* + Copyright (c) 2011 Arduino. All right reserved. + + This library is free software; you can redistribute it and/or + modify it under the terms of the GNU Lesser General Public + License as published by the Free Software Foundation; either + version 2.1 of the License, or (at your option) any later version. + + This library is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. + See the GNU Lesser General Public License for more details. + + You should have received a copy of the GNU Lesser General Public + License along with this library; if not, write to the Free Software + Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +*/ + +#ifndef _VARIANT_ARDUINO_STM32_ +#define _VARIANT_ARDUINO_STM32_ + +#ifdef __cplusplus +extern "C" { +#endif // __cplusplus + +/*---------------------------------------------------------------------------- + * Pins + *----------------------------------------------------------------------------*/ + +#define PA8 0 +#define PA9 1 +#define PA10 2 +#define PA11 3 +#define PA12 4 +#define PA13 5 +#define PA14 6 +#define PA15 7 +#define PB2 8 +#define PB3 9 +#define PB4 10 +#define PB5 11 +#define PB6 12 +#define PB7 13 +#define PB8 14 +#define PB9 15 +#define PB10 16 +#define PB11 17 +#define PB12 18 +#define PB13 19 +#define PB14 20 +#define PB15 21 +#define PC6 22 +#define PC7 23 +#define PC8 24 +#define PC9 25 +#define PC10 26 +#define PC11 27 +#define PC12 28 +#define PC13 29 +#define PC14 30 +#define PC15 31 +#define PD0 32 +#define PD1 33 +#define PD2 34 + +#define PA0 35 +#define PA1 36 +#define PA2 37 +#define PA3 38 +#define PA4 39 +#define PA5 40 +#define PA6 41 +#define PA7 42 +#define PB0 43 +#define PB1 44 +#define PC0 45 +#define PC1 46 +#define PC2 47 +#define PC3 48 +#define PC4 49 +#define PC5 50 + +// This must be a literal +#define NUM_DIGITAL_PINS 51 +// This must be a literal with a value less than or equal to to MAX_ANALOG_INPUTS +#define NUM_ANALOG_INPUTS 16 +#define NUM_ANALOG_FIRST 35 + +// On-board LED pin number +#define LED_BUILTIN PB11 +#define LED_GREEN LED_BUILTIN + +// Override default Arduino configuration +// SPI Definitions +#define PIN_SPI_SS PA4 +#define PIN_SPI_MOSI PA7 +#define PIN_SPI_MISO PA6 +#define PIN_SPI_SCK PA5 + +// I2C Definitions +#define PIN_WIRE_SDA PB7 +#define PIN_WIRE_SCL PB6 + +// Timer Definitions +#define TIMER_TONE TIM3 +#define TIMER_SERVO TIM2 + +// UART Definitions +// Define here Serial instance number to map on Serial generic name +#define SERIAL_UART_INSTANCE 1 + + +// Default pin used for 'Serial1' instance +#define PIN_SERIAL_RX PA10 +#define PIN_SERIAL_TX PA9 + +#ifdef __cplusplus +} // extern "C" +#endif +/*---------------------------------------------------------------------------- + * Arduino objects - C++ only + *----------------------------------------------------------------------------*/ + +#ifdef __cplusplus +// These serial port names are intended to allow libraries and architecture-neutral +// sketches to automatically default to the correct port name for a particular type +// of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN, +// the first hardware serial port whose RX/TX pins are not dedicated to another use. +// +// SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor +// +// SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial +// +// SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library +// +// SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins. +// +// SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX +// pins are NOT connected to anything by default. +#define SERIAL_PORT_MONITOR Serial +#define SERIAL_PORT_HARDWARE Serial1 +#endif + +#endif /* _VARIANT_ARDUINO_STM32_ */