diff --git a/boards.txt b/boards.txt
index 15322631d8..0c0c7b56e9 100644
--- a/boards.txt
+++ b/boards.txt
@@ -396,6 +396,18 @@ Disco.menu.pnum.DISCO_F030R8.build.product_line=STM32F030x8
Disco.menu.pnum.DISCO_F030R8.build.variant=DISCO_F030R8
Disco.menu.pnum.DISCO_F030R8.build.cmsis_lib_gcc=arm_cortexM0l_math
+# DISCO_F072RB board
+Disco.menu.pnum.DISCO_F072RB=STM32F072B-DISCOVERY
+Disco.menu.pnum.DISCO_F072RB.node="No_mass_storage_for_this_board_Use_STLink_upload_method"
+Disco.menu.pnum.DISCO_F072RB.upload.maximum_size=131072
+Disco.menu.pnum.DISCO_F072RB.upload.maximum_data_size=16384
+Disco.menu.pnum.DISCO_F072RB.build.mcu=cortex-m0
+Disco.menu.pnum.DISCO_F072RB.build.board=DISCO_F072RB
+Disco.menu.pnum.DISCO_F072RB.build.series=STM32F0xx
+Disco.menu.pnum.DISCO_F072RB.build.product_line=STM32F072xB
+Disco.menu.pnum.DISCO_F072RB.build.variant=DISCO_F072RB
+Disco.menu.pnum.DISCO_F072RB.build.cmsis_lib_gcc=arm_cortexM0l_math
+
#DISCO_F100RB board
# Support: Serial1 (USART1 on PA10, PA9) and Serial2 (USART3 on PB11, PB10)
Disco.menu.pnum.DISCO_F100RB=STM32F100RB-DISCVL
diff --git a/variants/DISCO_F072RB/PeripheralPins.c b/variants/DISCO_F072RB/PeripheralPins.c
new file mode 100644
index 0000000000..a412ee6987
--- /dev/null
+++ b/variants/DISCO_F072RB/PeripheralPins.c
@@ -0,0 +1,312 @@
+/*
+ *******************************************************************************
+ * Copyright (c) 2019, STMicroelectronics
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *******************************************************************************
+ * Automatically generated from STM32F072R(8-B)Tx.xml
+ */
+#include "Arduino.h"
+#include "PeripheralPins.h"
+
+/* =====
+ * Note: Commented lines are alternative possibilities which are not used per default.
+ * If you change them, you will have to know what you do
+ * =====
+ */
+
+//*** ADC ***
+
+#ifdef HAL_ADC_MODULE_ENABLED
+const PinMap PinMap_ADC[] = {
+ {PA_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC_IN0
+ {PA_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC_IN1
+#ifdef TSC_REMOVED
+ {PA_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC_IN2
+ {PA_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC_IN3
+#endif
+ {PA_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC_IN4
+ {PA_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC_IN5
+#ifdef TSC_REMOVED
+ {PA_6, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC_IN6
+ {PA_7, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC_IN7
+ {PB_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC_IN8
+ {PB_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC_IN9
+#endif
+ {PC_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC_IN10
+ {PC_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC_IN11
+ {PC_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC_IN12
+ {PC_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC_IN13
+ {PC_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC_IN14
+ {PC_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC_IN15
+ {NC, NP, 0}
+};
+#endif
+
+//*** DAC ***
+
+#ifdef HAL_DAC_MODULE_ENABLED
+const PinMap PinMap_DAC[] = {
+ {PA_4, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // DAC_OUT1
+ {PA_5, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // DAC_OUT2
+ {NC, NP, 0}
+};
+#endif
+
+//*** I2C ***
+
+#ifdef HAL_I2C_MODULE_ENABLED
+const PinMap PinMap_I2C_SDA[] = {
+ {PB_7, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C1)},
+ {PB_9, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C1)},
+ {PB_11, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C2)},
+ {PB_14, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF5_I2C2)},
+ {NC, NP, 0}
+};
+#endif
+
+#ifdef HAL_I2C_MODULE_ENABLED
+const PinMap PinMap_I2C_SCL[] = {
+ {PB_6, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C1)},
+ {PB_8, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C1)},
+ {PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C2)},
+ {PB_13, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF5_I2C2)},
+ {NC, NP, 0}
+};
+#endif
+
+//*** PWM ***
+
+#ifdef HAL_TIM_MODULE_ENABLED
+const PinMap PinMap_PWM[] = {
+ {PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 1, 0)}, // TIM2_CH1
+ {PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 2, 0)}, // TIM2_CH2
+// {PA_1, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM15, 1, 1)}, // TIM15_CH1N
+#ifdef TSC_REMOVED
+// {PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 3, 0)}, // TIM2_CH3
+ {PA_2, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM15, 1, 0)}, // TIM15_CH1
+ {PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 4, 0)}, // TIM2_CH4
+// {PA_3, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM15, 2, 0)}, // TIM15_CH2
+#endif
+ {PA_4, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_TIM14, 1, 0)}, // TIM14_CH1
+ {PA_5, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 1, 0)}, // TIM2_CH1
+#ifdef TSC_REMOVED
+ {PA_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 1, 0)}, // TIM3_CH1
+// {PA_6, TIM16, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM16, 1, 0)}, // TIM16_CH1
+ {PA_7, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 1)}, // TIM1_CH1N
+// {PA_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 2, 0)}, // TIM3_CH2
+// {PA_7, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_TIM14, 1, 0)}, // TIM14_CH1
+// {PA_7, TIM17, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM17, 1, 0)}, // TIM17_CH1
+#endif
+ {PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 0)}, // TIM1_CH1
+ {PA_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 0)}, // TIM1_CH2
+ {PA_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 0)}, // TIM1_CH3
+#ifdef USB_REMOVED
+ {PA_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 4, 0)}, // TIM1_CH4
+#endif
+ {PA_15, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 1, 0)}, // TIM2_CH1
+#ifdef TSC_REMOVED
+ {PB_0, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 1)}, // TIM1_CH2N
+// {PB_0, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 3, 0)}, // TIM3_CH3
+// {PB_1, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 1)}, // TIM1_CH3N
+// {PB_1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 4, 0)}, // TIM3_CH4
+ {PB_1, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM14, 1, 0)}, // TIM14_CH1
+#endif
+ {PB_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 2, 0)}, // TIM2_CH2
+ {PB_4, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 1, 0)}, // TIM3_CH1
+ {PB_5, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 2, 0)}, // TIM3_CH2
+ {PB_6, TIM16, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM16, 1, 1)}, // TIM16_CH1N
+ {PB_7, TIM17, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM17, 1, 1)}, // TIM17_CH1N
+ {PB_8, TIM16, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM16, 1, 0)}, // TIM16_CH1
+ {PB_9, TIM17, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM17, 1, 0)}, // TIM17_CH1
+ {PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 3, 0)}, // TIM2_CH3
+ {PB_11, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 4, 0)}, // TIM2_CH4
+ {PB_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 1)}, // TIM1_CH1N
+// {PB_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 1)}, // TIM1_CH2N
+ {PB_14, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM15, 1, 0)}, // TIM15_CH1
+// {PB_15, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 1)}, // TIM1_CH3N
+ {PB_15, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM15, 1, 1)}, // TIM15_CH1N
+// {PB_15, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM15, 2, 0)}, // TIM15_CH2
+ {PC_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM3, 1, 0)}, // TIM3_CH1
+ {PC_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM3, 2, 0)}, // TIM3_CH2
+ {PC_8, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM3, 3, 0)}, // TIM3_CH3
+ {PC_9, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM3, 4, 0)}, // TIM3_CH4
+ {NC, NP, 0}
+};
+#endif
+
+//*** SERIAL ***
+
+#ifdef HAL_UART_MODULE_ENABLED
+const PinMap PinMap_UART_TX[] = {
+ {PA_0, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART4)},
+#ifdef TSC_REMOVED
+ {PA_2, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+#endif
+ {PA_9, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)},
+ {PA_14, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+ {PB_6, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART1)},
+ {PB_10, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+ {PC_4, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART3)},
+// {PC_10, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART3)},
+ {PC_10, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART4)},
+ {NC, NP, 0}
+};
+#endif
+
+#ifdef HAL_UART_MODULE_ENABLED
+const PinMap PinMap_UART_RX[] = {
+ {PA_1, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART4)},
+#ifdef TSC_REMOVED
+ {PA_3, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+#endif
+ {PA_10, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)},
+ {PA_15, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+ {PB_7, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART1)},
+ {PB_11, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+ {PC_5, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART3)},
+// {PC_11, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART3)},
+ {PC_11, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART4)},
+ {NC, NP, 0}
+};
+#endif
+
+#ifdef HAL_UART_MODULE_ENABLED
+const PinMap PinMap_UART_RTS[] = {
+ {PA_1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+#ifdef USB_REMOVED
+ {PA_12, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)},
+#endif
+ {PA_15, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART4)},
+#ifdef TSC_REMOVED
+ {PB_1, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+#endif
+ {PB_14, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+ {PD_2, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART3)},
+ {NC, NP, 0}
+};
+#endif
+
+#ifdef HAL_UART_MODULE_ENABLED
+const PinMap PinMap_UART_CTS[] = {
+ {PA_0, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)},
+#ifdef TSC_REMOVED
+ {PA_6, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+#endif
+#ifdef TSC_REMOVED
+ {PA_11, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)},
+#endif
+ {PB_7, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART4)},
+ {PB_13, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)},
+ {NC, NP, 0}
+};
+#endif
+
+//*** SPI ***
+
+#ifdef HAL_SPI_MODULE_ENABLED
+const PinMap PinMap_SPI_MOSI[] = {
+#ifdef TSC_REMOVED
+ {PA_7, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+#endif
+ {PB_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)},
+ {PC_3, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)},
+ {NC, NP, 0}
+};
+#endif
+
+#ifdef HAL_SPI_MODULE_ENABLED
+const PinMap PinMap_SPI_MISO[] = {
+#ifdef TSC_REMOVED
+ {PA_6, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+#endif
+ {PB_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PB_14, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)},
+ {PC_2, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)},
+ {NC, NP, 0}
+};
+#endif
+
+#ifdef HAL_SPI_MODULE_ENABLED
+const PinMap PinMap_SPI_SCLK[] = {
+ {PA_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PB_3, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PB_10, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
+ {PB_13, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)},
+ {NC, NP, 0}
+};
+#endif
+
+#ifdef HAL_SPI_MODULE_ENABLED
+const PinMap PinMap_SPI_SSEL[] = {
+ {PA_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PA_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)},
+ {PB_9, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
+ {PB_12, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)},
+ {NC, NP, 0}
+};
+#endif
+
+//*** CAN ***
+
+#ifdef HAL_CAN_MODULE_ENABLED
+const PinMap PinMap_CAN_RD[] = {
+#ifdef USB_REMOVED
+ {PA_11, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF4_CAN)},
+#endif
+ {PB_8, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF4_CAN)},
+ {NC, NP, 0}
+};
+#endif
+
+#ifdef HAL_CAN_MODULE_ENABLED
+const PinMap PinMap_CAN_TD[] = {
+#ifdef USB_REMOVED
+ {PA_12, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF4_CAN)},
+#endif
+ {PB_9, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF4_CAN)},
+ {NC, NP, 0}
+};
+#endif
+
+//*** No ETHERNET ***
+
+//*** No QUADSPI ***
+
+//*** USB ***
+
+#ifdef HAL_PCD_MODULE_ENABLED
+const PinMap PinMap_USB[] = {
+ {PA_11, USB, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, GPIO_AF_NONE)}, // USB_DM
+ {PA_12, USB, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, GPIO_AF_NONE)}, // USB_DP
+// {PA_13, USB, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_USB)}, // USB_NOE
+ {NC, NP, 0}
+};
+#endif
+
+//*** No USB_OTG_FS ***
+
+//*** No USB_OTG_HS ***
diff --git a/variants/DISCO_F072RB/PinNamesVar.h b/variants/DISCO_F072RB/PinNamesVar.h
new file mode 100644
index 0000000000..ed2a559763
--- /dev/null
+++ b/variants/DISCO_F072RB/PinNamesVar.h
@@ -0,0 +1,31 @@
+ /* SYS_WKUP */
+#ifdef PWR_WAKEUP_PIN1
+ SYS_WKUP1 = PA_0,
+#endif
+#ifdef PWR_WAKEUP_PIN2
+ SYS_WKUP2 = PC_13,
+#endif
+#ifdef PWR_WAKEUP_PIN3
+ SYS_WKUP3 = PE_6, /* Manually updated */
+#endif
+#ifdef PWR_WAKEUP_PIN4
+ SYS_WKUP4 = PA_2,
+#endif
+#ifdef PWR_WAKEUP_PIN5
+ SYS_WKUP5 = PC_5,
+#endif
+#ifdef PWR_WAKEUP_PIN6
+ SYS_WKUP6 = PB_5,
+#endif
+#ifdef PWR_WAKEUP_PIN7
+ SYS_WKUP7 = PB_15,
+#endif
+#ifdef PWR_WAKEUP_PIN8
+ SYS_WKUP8 = PF_2, /* Manually updated */
+#endif
+ /* USB */
+#ifdef USBCON
+ USB_DM = PA_11,
+ USB_DP = PA_12,
+ USB_NOE = PA_13,
+#endif
diff --git a/variants/DISCO_F072RB/ldscript.ld b/variants/DISCO_F072RB/ldscript.ld
new file mode 100644
index 0000000000..44015746d5
--- /dev/null
+++ b/variants/DISCO_F072RB/ldscript.ld
@@ -0,0 +1,188 @@
+/*
+*****************************************************************************
+**
+
+** File : ldscript.ld
+**
+** Abstract : Linker script for STM32F072RB Device with
+** 128KByte FLASH, 16KByte RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+**
+** Distribution: The file is distributed as is, without any warranty
+** of any kind.
+**
+*****************************************************************************
+** @attention
+**
+** © COPYRIGHT(c) 2014 Ac6
+**
+** Redistribution and use in source and binary forms, with or without modification,
+** are permitted provided that the following conditions are met:
+** 1. Redistributions of source code must retain the above copyright notice,
+** this list of conditions and the following disclaimer.
+** 2. Redistributions in binary form must reproduce the above copyright notice,
+** this list of conditions and the following disclaimer in the documentation
+** and/or other materials provided with the distribution.
+** 3. Neither the name of Ac6 nor the names of its contributors
+** may be used to endorse or promote products derived from this software
+** without specific prior written permission.
+**
+** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = 0x20004000; /* end of RAM */
+/* Generate a link error if heap and stack don't fit into RAM */
+_Min_Heap_Size = 0x200; /* required amount of heap */
+_Min_Stack_Size = 0x400; /* required amount of stack */
+
+/* Specify the memory areas */
+MEMORY
+{
+RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 16K
+FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 128K
+}
+
+/* Define output sections */
+SECTIONS
+{
+ /* The startup code goes first into FLASH */
+ .isr_vector :
+ {
+ . = ALIGN(4);
+ KEEP(*(.isr_vector)) /* Startup code */
+ . = ALIGN(4);
+ } >FLASH
+
+ /* The program code and other data goes into FLASH */
+ .text :
+ {
+ . = ALIGN(4);
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ . = ALIGN(4);
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data goes into FLASH */
+ .rodata :
+ {
+ . = ALIGN(4);
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
+ .ARM : {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections goes into RAM, load LMA copy after code */
+ .data :
+ {
+ . = ALIGN(4);
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+
+ . = ALIGN(4);
+ _edata = .; /* define a global symbol at data end */
+ } >RAM AT> FLASH
+
+
+ /* Uninitialized data section */
+ . = ALIGN(4);
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss secion */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ . = ALIGN(4);
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough RAM left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(4);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(4);
+ } >RAM
+
+
+
+ /* Remove information from the standard libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
+
+
diff --git a/variants/DISCO_F072RB/stm32f0xx_hal_conf.h b/variants/DISCO_F072RB/stm32f0xx_hal_conf.h
new file mode 100644
index 0000000000..3396de875d
--- /dev/null
+++ b/variants/DISCO_F072RB/stm32f0xx_hal_conf.h
@@ -0,0 +1,312 @@
+/**
+ ******************************************************************************
+ * @file stm32f0xx_hal_conf.h
+ * @author MCD Application Team
+ * @brief HAL configuration file.
+ ******************************************************************************
+ * @attention
+ *
+ * © COPYRIGHT(c) 2016 STMicroelectronics
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F0xx_HAL_CONF_H
+#define __STM32F0xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+ * @brief This is the list of modules to be used in the HAL driver
+ */
+#define HAL_MODULE_ENABLED
+#define HAL_ADC_MODULE_ENABLED
+/*#define HAL_CAN_MODULE_ENABLED */
+/*#define HAL_CEC_MODULE_ENABLED */
+/*#define HAL_COMP_MODULE_ENABLED */
+#define HAL_CORTEX_MODULE_ENABLED
+/*#define HAL_CRC_MODULE_ENABLED */
+#define HAL_DAC_MODULE_ENABLED
+#define HAL_DMA_MODULE_ENABLED
+#define HAL_FLASH_MODULE_ENABLED
+#define HAL_GPIO_MODULE_ENABLED
+#define HAL_I2C_MODULE_ENABLED
+/*#define HAL_I2S_MODULE_ENABLED */
+/*#define HAL_IRDA_MODULE_ENABLED */
+#define HAL_IWDG_MODULE_ENABLED
+/*#define HAL_PCD_MODULE_ENABLED */
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+#define HAL_RTC_MODULE_ENABLED
+/*#define HAL_SMARTCARD_MODULE_ENABLED */
+/*#define HAL_SMBUS_MODULE_ENABLED */
+#define HAL_SPI_MODULE_ENABLED
+#define HAL_TIM_MODULE_ENABLED
+/*#define HAL_TSC_MODULE_ENABLED */
+/*#define HAL_UART_MODULE_ENABLED */
+/*#define HAL_USART_MODULE_ENABLED */
+/*#define HAL_WWDG_MODULE_ENABLED */
+
+/* ######################### Oscillator Values adaptation ################### */
+/**
+ * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSE is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSE_VALUE)
+ #define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+/**
+ * @brief In the following line adjust the External High Speed oscillator (HSE) Startup
+ * Timeout value
+ */
+#if !defined (HSE_STARTUP_TIMEOUT)
+ #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal High Speed oscillator (HSI) value.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSI is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSI_VALUE)
+ #define HSI_VALUE 8000000U /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+ * @brief In the following line adjust the Internal High Speed oscillator (HSI) Startup
+ * Timeout value
+ */
+#if !defined (HSI_STARTUP_TIMEOUT)
+ #define HSI_STARTUP_TIMEOUT 5000U /*!< Time out for HSI start up */
+#endif /* HSI_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal High Speed oscillator for ADC (HSI14) value.
+ */
+#if !defined (HSI14_VALUE)
+ #define HSI14_VALUE 14000000U /*!< Value of the Internal High Speed oscillator for ADC in Hz.
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+#endif /* HSI14_VALUE */
+
+/**
+ * @brief Internal High Speed oscillator for USB (HSI48) value.
+ */
+#if !defined (HSI48_VALUE)
+ #define HSI48_VALUE 48000000U /*!< Value of the Internal High Speed oscillator for USB in Hz.
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+#endif /* HSI48_VALUE */
+
+/**
+ * @brief Internal Low Speed oscillator (LSI) value.
+ */
+#if !defined (LSI_VALUE)
+ #define LSI_VALUE 40000U
+#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+/**
+ * @brief External Low Speed oscillator (LSE) value.
+ */
+#if !defined (LSE_VALUE)
+ #define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+/**
+ * @brief Time out for LSE start up value in ms.
+ */
+#if !defined (LSE_STARTUP_TIMEOUT)
+ #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+ === you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+ * @brief This is the HAL system configuration section
+ */
+#define VDD_VALUE 3300U /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY ((uint32_t)(1U<<__NVIC_PRIO_BITS) - 1U) /*!< tick interrupt priority (lowest by default) */
+ /* Warning: Must be set to higher priority for HAL_Delay() */
+ /* and HAL_GetTick() usage under interrupt context */
+#define USE_RTOS 0U
+#define PREFETCH_ENABLE 1U
+#define INSTRUCTION_CACHE_ENABLE 0U
+#define DATA_CACHE_ENABLE 0U
+#define USE_SPI_CRC 1U
+
+/* ########################## Assert Selection ############################## */
+/**
+ * @brief Uncomment the line below to expanse the "assert_param" macro in the
+ * HAL drivers code
+ */
+/*#define USE_FULL_ASSERT 1*/
+
+/* Includes ------------------------------------------------------------------*/
+/**
+ * @brief Include module's header file
+ */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+ #include "stm32f0xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+ #include "stm32f0xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+ #include "stm32f0xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+ #include "stm32f0xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+ #include "stm32f0xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+ #include "stm32f0xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CEC_MODULE_ENABLED
+ #include "stm32f0xx_hal_cec.h"
+#endif /* HAL_CEC_MODULE_ENABLED */
+
+#ifdef HAL_COMP_MODULE_ENABLED
+ #include "stm32f0xx_hal_comp.h"
+#endif /* HAL_COMP_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+ #include "stm32f0xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+ #include "stm32f0xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+ #include "stm32f0xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32f0xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32f0xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32f0xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32f0xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32f0xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32f0xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32f0xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32f0xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_SMBUS_MODULE_ENABLED
+ #include "stm32f0xx_hal_smbus.h"
+#endif /* HAL_SMBUS_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32f0xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32f0xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_TSC_MODULE_ENABLED
+ #include "stm32f0xx_hal_tsc.h"
+#endif /* HAL_TSC_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32f0xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32f0xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32f0xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+/**
+ * @brief The assert_param macro is used for function's parameters check.
+ * @param expr If expr is false, it calls assert_failed function
+ * which reports the name of the source file and the source
+ * line number of the call that failed.
+ * If expr is true, it returns no value.
+ * @retval None
+ */
+ #define assert_param(expr) ((expr) ? (void)0U : assert_failed((char *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+ void assert_failed(char* file, uint32_t line);
+#else
+ #define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F0xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/variants/DISCO_F072RB/variant.cpp b/variants/DISCO_F072RB/variant.cpp
new file mode 100644
index 0000000000..c694a2fe3b
--- /dev/null
+++ b/variants/DISCO_F072RB/variant.cpp
@@ -0,0 +1,176 @@
+/*
+ *******************************************************************************
+ * Copyright (c) 2018, STMicroelectronics
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *******************************************************************************
+ */
+
+#include "variant.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+// Pin number
+const PinName digitalPin[] = {
+//P2 connector Right side (top view)
+ PB_9, //D0
+ PB_8, //D1
+ PB_7, //D2
+ PB_6, //D3
+ PB_5, //D4
+ PB_4, //D5
+ PB_3, //D6
+ PD_2, //D7
+ PC_12, //D8
+ PC_11, //D9
+ PC_10, //D10
+ PA_15, //D11
+ PA_14, //D12
+ PA_13, //D13
+#ifdef USB_REMOVED
+ PA_12, //D14
+ PA_11, //D15
+#else
+ NC,
+ NC,
+#endif
+ PA_10, //D16
+ PA_9, //D17
+ PA_8, //D18
+ PC_9, //D19
+ PC_8, //D20
+ PC_7, //D21
+ PC_6, //D22
+ PB_15, //D23
+ PB_14, //D24
+ PB_13, //D25
+//P1 connector Left side (top view)
+ PC_13, //D26
+ PC_14, //D27
+ PC_15, //D28
+ PF_0, //D29
+ PF_1, //D30
+ PC_0, //D31
+ PC_1, //D32
+ PC_2, //D33
+ PC_3, //D34
+ PA_0, //D35
+ PA_1, //D36
+#ifdef TSC_REMOVED
+ PA_2, //D37
+ PA_3, //D38
+#else
+ NC,
+ NC,
+#endif
+ PA_4, //D39
+ PA_5, //D40
+#ifdef TSC_REMOVED
+ PA_6, //D41
+ PA_7, //D42
+#else
+ NC,
+ NC,
+#endif
+ PC_4, //D43
+ PC_5, //D44
+#ifdef TSC_REMOVED
+ PB_0, //D45
+ PB_1, //D46
+#else
+ NC,
+ NC,
+#endif
+ PB_2, //D47
+ PB_10, //D48
+ PB_11, //D49
+ PB_12, //D50
+};
+
+#ifdef __cplusplus
+}
+#endif
+
+// ----------------------------------------------------------------------------
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+ * @brief System Clock Configuration
+ * @param None
+ * @retval None
+ */
+WEAK void SystemClock_Config(void)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_PeriphCLKInitTypeDef PeriphClkInit;
+
+ /* Initializes the CPU, AHB and APB busses clocks */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI|RCC_OSCILLATORTYPE_HSI48;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSI48State = RCC_HSI48_ON;
+ RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL6;
+ RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV1;
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ Error_Handler();
+ }
+ /* Initializes the CPU, AHB and APB busses clocks */
+ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
+ |RCC_CLOCKTYPE_PCLK1;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
+
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1) != HAL_OK) {
+ Error_Handler();
+ }
+ PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USB;
+ PeriphClkInit.UsbClockSelection = RCC_USBCLKSOURCE_HSI48;
+
+ if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK) {
+ Error_Handler();
+ }
+
+ /* Configure the Systick interrupt time */
+ HAL_SYSTICK_Config(HAL_RCC_GetHCLKFreq()/1000);
+
+ /* Configure the Systick */
+ HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK);
+
+ /* SysTick_IRQn interrupt configuration */
+ HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0);
+}
+
+#ifdef __cplusplus
+}
+#endif
diff --git a/variants/DISCO_F072RB/variant.h b/variants/DISCO_F072RB/variant.h
new file mode 100644
index 0000000000..a8217ad3d2
--- /dev/null
+++ b/variants/DISCO_F072RB/variant.h
@@ -0,0 +1,189 @@
+/*
+ *******************************************************************************
+ * Copyright (c) 2018, STMicroelectronics
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *******************************************************************************
+ */
+
+#ifndef _VARIANT_ARDUINO_STM32_
+#define _VARIANT_ARDUINO_STM32_
+
+/*----------------------------------------------------------------------------
+ * Headers
+ *----------------------------------------------------------------------------*/
+
+#include "PeripheralPins.h"
+
+#ifdef __cplusplus
+extern "C"{
+#endif // __cplusplus
+
+/*----------------------------------------------------------------------------
+ * Pins
+ *----------------------------------------------------------------------------*/
+extern const PinName digitalPin[];
+
+// USB USER CN2
+// By default, SB20,23 (USB-USER) are OFF.
+// So PA11,12 are not available.
+// If ON and R12,13 removed,
+// #define USB_REMOVED
+// to get PA11,12 available.
+
+// Linear touch sensor
+// By default, SB27,28,29,30,31,32 (touch sensor) are OFF.
+// So PA2,3,6,7 and PB0,1 are not available.
+// If ON and R38,39,40 and C26,27,28 are removed,
+// #define TSC_REMOVED
+// to get PA2,3,6,7 and PB0,1 available.
+
+// P2 connector Right side (top view)
+#define PB9 0
+#define PB8 1
+#define PB7 2
+#define PB6 3
+#define PB5 4
+#define PB4 5
+#define PB3 6
+#define PD2 7
+#define PC12 8
+#define PC11 9
+#define PC10 10
+#define PA15 11
+#define PA14 12
+#define PA13 13
+#define PA12 14 // SB20 (default OFF): USB_DP
+#define PA11 15 // SB23 (default OFF): USB_DM
+#define PA10 16
+#define PA9 17
+#define PA8 18
+#define PC9 19 // LED_GREEN (LD4)
+#define PC8 20 // LED_ORANGE (LD3)
+#define PC7 21 // LED_BLUE (LD6)
+#define PC6 22 // LED_RED (LD5)
+#define PB15 23 // SPI2_MOSI (L3GD20)
+#define PB14 24 // SPI2_MISO (L3GD20)
+#define PB13 25 // SPI2_SCK (L3GD20)
+// P1 connector Left side (top view)
+#define PC13 26
+#define PC14 27
+#define PC15 28
+#define PF0 29
+#define PF1 30
+#define PC0 31 // A0 - NCS_MEMS_SPI (L3GD20)
+#define PC1 32 // A1 - MEMS INT1 (L3GD20)
+#define PC2 33 // A2 - MEMS INT2 (L3GD20)
+#define PC3 34 // A3
+#define PA0 35 // A4 - USER_BTN
+#define PA1 36 // A5
+#define PA2 37 // A6 - SB27 (default OFF): TS_G1_IO3
+#define PA3 38 // A7 - SB28 (default OFF): TS_G1_IO4
+#define PA4 39 // A8
+#define PA5 40 // A9
+#define PA6 41 // A10 - SB29 (default OFF): TS_G2_IO3
+#define PA7 42 // A11 - SB30 (default OFF): TS_G2_IO4
+#define PC4 43 // A12
+#define PC5 44 // A13 - Ext Reset
+#define PB0 45 // A14 - SB31 (default OFF): TS_G3_IO2
+#define PB1 46 // A15 - SB32 (default OFF): TS_G3_IO3
+#define PB2 47
+#define PB10 48 // I2C2 SCL: Extension / RF EEprom Connector
+#define PB11 49 // I2C2 SDA: Extension / RF EEprom Connector
+#define PB12 50
+
+// This must be a literal
+#define NUM_DIGITAL_PINS 51
+// This must be a literal with a value less than or equal to to MAX_ANALOG_INPUTS
+#define NUM_ANALOG_INPUTS 16
+#define NUM_ANALOG_FIRST 31
+
+//On-board LED pin number
+#define LED_BUILTIN PC9
+#define LED_GREEN LED_BUILTIN
+#define LED_ORANGE PC8
+#define LED_BLUE PC7
+#define LED_RED PC6
+
+//On-board user button
+#define USER_BTN PA0
+
+// SPI definitions
+// SPI1 is used
+#define PIN_SPI_SS PA4
+#define PIN_SPI_SS1 PC4
+#define PIN_SPI_SS2 PB12
+#define PIN_SPI_SS3 PB6
+#define PIN_SPI_MOSI PB5
+#define PIN_SPI_MISO PB4
+#define PIN_SPI_SCK PB3
+
+// I2C Definitions
+// I2C1 is used
+#define PIN_WIRE_SDA PB9
+#define PIN_WIRE_SCL PB8
+
+// Timer Definitions
+//Do not use timer used by PWM pins when possible. See PinMap_PWM.
+#define TIMER_TONE TIM6
+
+//Do not use basic timer: OC is required
+#define TIMER_SERVO TIM3 //TODO: advanced-control timers don't work
+
+// UART Definitions
+#define SERIAL_UART_INSTANCE 1 // USART 1
+
+// Mandatory for Firmata
+#define PIN_SERIAL_RX PA10
+#define PIN_SERIAL_TX PA9
+
+#ifdef __cplusplus
+} // extern "C"
+#endif
+/*----------------------------------------------------------------------------
+ * Arduino objects - C++ only
+ *----------------------------------------------------------------------------*/
+
+#ifdef __cplusplus
+// These serial port names are intended to allow libraries and architecture-neutral
+// sketches to automatically default to the correct port name for a particular type
+// of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN,
+// the first hardware serial port whose RX/TX pins are not dedicated to another use.
+//
+// SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor
+//
+// SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial
+//
+// SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library
+//
+// SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins.
+//
+// SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX
+// pins are NOT connected to anything by default.
+#define SERIAL_PORT_MONITOR Serial
+#define SERIAL_PORT_HARDWARE Serial
+#endif
+
+#endif /* _VARIANT_ARDUINO_STM32_ */