diff --git a/boards.txt b/boards.txt index d7524d1f82..0cea1edd4b 100644 --- a/boards.txt +++ b/boards.txt @@ -300,6 +300,20 @@ Disco.build.core=arduino Disco.build.board=Disco Disco.build.extra_flags=-D{build.product_line} {build.enable_usb} {build.xSerial} +# DISCO_F030R8 board +# Support: Serial1 (USART1 on PA10, PA9) +Disco.menu.pnum.DISCO_F030R8=STM32F030R8-DISCVL +Disco.menu.pnum.DISCO_F030R8.node=DIS_F030R8 +Disco.menu.pnum.DISCO_F030R8.upload.maximum_size=65536 +Disco.menu.pnum.DISCO_F030R8.upload.maximum_data_size=8192 +Disco.menu.pnum.DISCO_F030R8.build.mcu=cortex-m0 +Disco.menu.pnum.DISCO_F030R8.build.f_cpu=48000000L +Disco.menu.pnum.DISCO_F030R8.build.board=DISCO_F030R8 +Disco.menu.pnum.DISCO_F030R8.build.series=STM32F0xx +Disco.menu.pnum.DISCO_F030R8.build.product_line=STM32F030x8 +Disco.menu.pnum.DISCO_F030R8.build.variant=DISCO_F030R8 +Disco.menu.pnum.DISCO_F030R8.build.cmsis_lib_gcc=arm_cortexM0l_math + #DISCO_F100RB board # Support: Serial1 (USART1 on PA10, PA9) and Serial2 (USART3 on PB11, PB10) Disco.menu.pnum.DISCO_F100RB=STM32F100RB-DISCVL diff --git a/variants/DISCO_F030R8/PeripheralPins.c b/variants/DISCO_F030R8/PeripheralPins.c new file mode 100644 index 0000000000..7bf06a4627 --- /dev/null +++ b/variants/DISCO_F030R8/PeripheralPins.c @@ -0,0 +1,181 @@ +/* + ******************************************************************************* + * Copyright (c) 2016, STMicroelectronics + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + ******************************************************************************* + */ +#include "Arduino.h" +#include "PeripheralPins.h" + +// ===== +// Note: Commented lines are alternative possibilities which are not used per default. +// If you change them, you will have to know what you do +// ===== + + +//*** ADC *** + +const PinMap PinMap_ADC[] = { + {PA_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC_IN0 + {PA_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC_IN1 +// {PA_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC_IN2 - STLink Tx +// {PA_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC_IN3 - STLink Rx + {PA_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC_IN4 +// {PA_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC_IN5 + {PA_6, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC_IN6 + {PA_7, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC_IN7 + {PB_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC_IN8 +// {PB_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC_IN9 + {PC_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC_IN10 + {PC_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC_IN11 + {PC_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC_IN12 + {PC_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC_IN13 + {PC_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC_IN14 + {PC_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC_IN15 + {NC, NP, 0} +}; + +//*** DAC *** +// No DAC + +//*** I2C *** + +const PinMap PinMap_I2C_SDA[] = { + {PB_7, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C1)}, + {PB_9, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C1)}, + {PB_11, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C2)}, + {NC, NP, 0} +}; + +const PinMap PinMap_I2C_SCL[] = { + {PB_6, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C1)}, + {PB_8, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C1)}, + {PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF1_I2C2)}, + {NC, NP, 0} +}; + +//*** PWM *** + +const PinMap PinMap_PWM[] = { +// {PA_2, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM15, 1, 0)}, // TIM15_CH1 - STLink Tx +// {PA_3, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM15, 2, 0)}, // TIM15_CH2 - STLink Rx + {PA_4, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_TIM14, 1, 0)}, // TIM14_CH1 +// {PA_6, TIM16, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM16, 1, 0)}, // TIM16_CH1 + {PA_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 1, 0)}, // TIM3_CH1 +// {PA_7, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_TIM14, 1, 0)}, // TIM14_CH1 +// {PA_7, TIM17, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM17, 1, 0)}, // TIM17_CH1 +// {PA_7, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 1)}, // TIM1_CH1N + {PA_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 2, 0)}, // TIM3_CH2 + {PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 0)}, // TIM1_CH1 + //{PA_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 0)}, // TIM1_CH2 + //{PA_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 0)}, // TIM1_CH3 + {PA_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 4, 0)}, // TIM1_CH4 + {PB_0, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 1)}, // TIM1_CH2N + {PB_0, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 3, 0)}, // TIM3_CH3 +// {PB_1, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM14, 1, 0)}, // TIM14_CH1 +// {PB_1, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 1)}, // TIM1_CH3N + {PB_1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 4, 0)}, // TIM3_CH4 + {PB_4, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 1, 0)}, // TIM3_CH1 + {PB_5, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 2, 0)}, // TIM3_CH2 + {PB_6, TIM16, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM16, 1, 1)}, // TIM16_CH1N + {PB_7, TIM17, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM17, 1, 1)}, // TIM17_CH1N + {PB_8, TIM16, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM16, 1, 0)}, // TIM16_CH1 + {PB_9, TIM17, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM17, 1, 0)}, // TIM17_CH1 + {PB_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 1)}, // TIM1_CH1N + {PB_14, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM15, 1, 0)}, // TIM15_CH1 +// {PB_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 1)}, // TIM1_CH2N +// {PB_15, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM15, 1, 1)}, // TIM15_CH1N + {PB_15, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM15, 2, 0)}, // TIM15_CH2 +// {PB_15, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 1)}, // TIM1_CH3N + {PC_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_MCO, 1, 0)}, // TIM3_CH1 + {PC_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_MCO, 2, 0)}, // TIM3_CH2 + {PC_8, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 3, 0)}, // Blue LED + {PC_9, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_MCO, 4, 0)}, // Green LED + {NC, NP, 0} +}; + +//*** SERIAL *** + +const PinMap PinMap_UART_TX[] = { + {PA_2, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)}, + {PA_9, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)}, + {PA_14, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)}, + //{PB_6, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART1)}, + {NC, NP, 0} +}; + +const PinMap PinMap_UART_RX[] = { + {PA_3, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)}, + {PA_10, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)}, + {PA_15, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)}, + //{PB_7, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART1)}, + {NC, NP, 0} +}; + +const PinMap PinMap_UART_RTS[] = { + {PA_1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)}, + {PA_12, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)}, + {NC, NP, 0} +}; + +const PinMap PinMap_UART_CTS[] = { + {PA_0, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)}, + {PA_11, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)}, + {NC, NP, 0} +}; + +//*** SPI *** + +const PinMap PinMap_SPI_MOSI[] = { + {PA_7, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PB_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)}, + {NC, NP, 0} +}; + +const PinMap PinMap_SPI_MISO[] = { + {PA_6, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PB_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PB_14, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)}, + {NC, NP, 0} +}; + +const PinMap PinMap_SPI_SCLK[] = { + {PA_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, // LED + {PB_3, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PB_13, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)}, + {NC, NP, 0} +}; + +const PinMap PinMap_SPI_SSEL[] = { + {PA_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PA_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PB_12, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)}, + {NC, NP, 0} +}; + +//*** CAN *** +// No CAN diff --git a/variants/DISCO_F030R8/ldscript.ld b/variants/DISCO_F030R8/ldscript.ld new file mode 100644 index 0000000000..1aae47014f --- /dev/null +++ b/variants/DISCO_F030R8/ldscript.ld @@ -0,0 +1,167 @@ +/* +***************************************************************************** +** + +** File : LinkerScript.ld +** +** Abstract : Linker script for STM32F030R8Tx Device with +** 64KByte FLASH, 8KByte RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** +** Distribution: The file is distributed as is, without any warranty +** of any kind. +** +** (c)Copyright Ac6. +** You may use this file as-is or modify it according to the needs of your +** project. Distribution of this file (unmodified or modified) is not +** permitted. Ac6 permit registered System Workbench for MCU users the +** rights to distribute the assembled, compiled & linked contents of this +** file as part of an application binary file, provided that it is built +** using the System Workbench for MCU toolchain. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20002000; /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x400; /* required amount of heap */ +_Min_Stack_Size = 0x860; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ +FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 64K +RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 8K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text ALIGN(4): + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} diff --git a/variants/DISCO_F030R8/stm32f0xx_hal_conf.h b/variants/DISCO_F030R8/stm32f0xx_hal_conf.h new file mode 100644 index 0000000000..04e82c19c6 --- /dev/null +++ b/variants/DISCO_F030R8/stm32f0xx_hal_conf.h @@ -0,0 +1,322 @@ +/** + ****************************************************************************** + * @file stm32f0xx_hal_conf.h + * @author MCD Application Team + * @version V1.5.0 + * @date 04-November-2016 + * @brief HAL configuration file. + ****************************************************************************** + * @attention + * + *

© COPYRIGHT(c) 2016 STMicroelectronics

+ * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F0xx_HAL_CONF_H +#define __STM32F0xx_HAL_CONF_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +#define HAL_ADC_MODULE_ENABLED +//#define HAL_CAN_MODULE_ENABLED +//#define HAL_CEC_MODULE_ENABLED +//#define HAL_COMP_MODULE_ENABLED +#define HAL_CORTEX_MODULE_ENABLED +//#define HAL_CRC_MODULE_ENABLED +//#define HAL_DAC_MODULE_ENABLED +#define HAL_DMA_MODULE_ENABLED +#define HAL_FLASH_MODULE_ENABLED +#define HAL_GPIO_MODULE_ENABLED +#define HAL_I2C_MODULE_ENABLED +//#define HAL_I2S_MODULE_ENABLED +//#define HAL_IRDA_MODULE_ENABLED +//#define HAL_IWDG_MODULE_ENABLED +//#define HAL_PCD_MODULE_ENABLED +//#define HAL_PWR_MODULE_ENABLED +#define HAL_RCC_MODULE_ENABLED +//#define HAL_RTC_MODULE_ENABLED +//#define HAL_SMARTCARD_MODULE_ENABLED +//#define HAL_SMBUS_MODULE_ENABLED +#define HAL_SPI_MODULE_ENABLED +#define HAL_TIM_MODULE_ENABLED +//#define HAL_TSC_MODULE_ENABLED +#define HAL_UART_MODULE_ENABLED +//#define HAL_USART_MODULE_ENABLED +//#define HAL_WWDG_MODULE_ENABLED + +/* ######################### Oscillator Values adaptation ################### */ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) + #define HSE_VALUE (8000000U) /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +/** + * @brief In the following line adjust the External High Speed oscillator (HSE) Startup + * Timeout value + */ +#if !defined (HSE_STARTUP_TIMEOUT) + #define HSE_STARTUP_TIMEOUT (100U) /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) + #define HSI_VALUE (8000000U) /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + +/** + * @brief In the following line adjust the Internal High Speed oscillator (HSI) Startup + * Timeout value + */ +#if !defined (HSI_STARTUP_TIMEOUT) + #define HSI_STARTUP_TIMEOUT (5000U) /*!< Time out for HSI start up */ +#endif /* HSI_STARTUP_TIMEOUT */ + +/** + * @brief Internal High Speed oscillator for ADC (HSI14) value. + */ +#if !defined (HSI14_VALUE) +#define HSI14_VALUE (14000000U) /*!< Value of the Internal High Speed oscillator for ADC in Hz. + The real value may vary depending on the variations + in voltage and temperature. */ +#endif /* HSI14_VALUE */ + +/** + * @brief Internal High Speed oscillator for USB (HSI48) value. + */ +#if !defined (HSI48_VALUE) +#define HSI48_VALUE (48000000U) /*!< Value of the Internal High Speed oscillator for USB in Hz. + The real value may vary depending on the variations + in voltage and temperature. */ +#endif /* HSI48_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#if !defined (LSI_VALUE) + #define LSI_VALUE (40000U) +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature. */ +/** + * @brief External Low Speed oscillator (LSE) value. + */ +#if !defined (LSE_VALUE) + #define LSE_VALUE (32768U) /*!< Value of the External Low Speed oscillator in Hz */ +#endif /* LSE_VALUE */ + +/** + * @brief Time out for LSE start up value in ms. + */ +#if !defined (LSE_STARTUP_TIMEOUT) + #define LSE_STARTUP_TIMEOUT (5000U) /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY ((uint32_t)(1<<__NVIC_PRIO_BITS) - 1) /*!< tick interrupt priority (lowest by default) */ + /* Warning: Must be set to higher priority for HAL_Delay() */ + /* and HAL_GetTick() usage under interrupt context */ +#define USE_RTOS 0 +#define PREFETCH_ENABLE 1 +#define INSTRUCTION_CACHE_ENABLE 0 +#define DATA_CACHE_ENABLE 0 + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/*#define USE_FULL_ASSERT 1*/ + +/* ################## SPI peripheral configuration ########################## */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver +* Activated: CRC code is present inside driver +* Deactivated: CRC code cleaned from driver +*/ + +#define USE_SPI_CRC 0U + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED + #include "stm32f0xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED + #include "stm32f0xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED + #include "stm32f0xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + #include "stm32f0xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED + #include "stm32f0xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CAN_MODULE_ENABLED + #include "stm32f0xx_hal_can.h" +#endif /* HAL_CAN_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED + #include "stm32f0xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_COMP_MODULE_ENABLED + #include "stm32f0xx_hal_comp.h" +#endif /* HAL_COMP_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED + #include "stm32f0xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED + #include "stm32f0xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED + #include "stm32f0xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED + #include "stm32f0xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED + #include "stm32f0xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED + #include "stm32f0xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED + #include "stm32f0xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED + #include "stm32f0xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED + #include "stm32f0xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED + #include "stm32f0xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED + #include "stm32f0xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_SMBUS_MODULE_ENABLED + #include "stm32f0xx_hal_smbus.h" +#endif /* HAL_SMBUS_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED + #include "stm32f0xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED + #include "stm32f0xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_TSC_MODULE_ENABLED + #include "stm32f0xx_hal_tsc.h" +#endif /* HAL_TSC_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED + #include "stm32f0xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED + #include "stm32f0xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED + #include "stm32f0xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t* file, uint32_t line); +#else + #define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F0xx_HAL_CONF_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/variants/DISCO_F030R8/variant.cpp b/variants/DISCO_F030R8/variant.cpp new file mode 100644 index 0000000000..1dc5c484ca --- /dev/null +++ b/variants/DISCO_F030R8/variant.cpp @@ -0,0 +1,168 @@ +/* + Copyright (c) 2011 Arduino. All right reserved. + + This library is free software; you can redistribute it and/or + modify it under the terms of the GNU Lesser General Public + License as published by the Free Software Foundation; either + version 2.1 of the License, or (at your option) any later version. + + This library is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. + See the GNU Lesser General Public License for more details. + + You should have received a copy of the GNU Lesser General Public + License along with this library; if not, write to the Free Software + Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +*/ + +#include "variant.h" + +#ifdef __cplusplus +extern "C" { +#endif + +// Pin number +const PinName digitalPin[] = { + //P1 connector Right side (bottom view) + PC_13, //D0 + PC_14, //D1 + PC_15, //D2 + PF_0, //D3 + PF_1, //D4 + PC_0, //D5 + PC_1, //D6 + PC_2, //D7 + PC_3, //D8 + PA_0, //D9 + PA_1, //D10 + PA_2, //D11 + PA_3, //D12 + PF_4, //D13 + PF_5, //D14 + PA_4, //D15 + PA_5, //D16 + PA_6, //D17 + PA_7, //D18 + PC_4, //D19 + PC_5, //D20 + PB_0, //D21 + PB_1, //D22 + PB_2, //D23 + PB_10, //D24 + PB_11, //D25 + PB_12, //D26 + //P2 connector Left side (bottom view) + PB_9, //D27 + PB_8, //D28 + PB_7, //D29 + PB_6, //D30 + PB_5, //D31 + PB_4, //D32 + PB_3, //D33 + PD_2, //D34 + PC_12, //D35 + PC_11, //D36 + PC_10, //D37 + PA_15, //D38 + PA_14, //D39 + PF_7, //D40 + PF_6, //D41 + PA_13, //D42 + PA_12, //D43 + PA_11, //D44 + PA_10, //D45 + PA_9, //D46 + PA_8, //D47 + PC_9, //D48 + PC_8, //D49 + PC_7, //D50 + PC_6, //D51 + PB_15, //D52 + PB_14, //D53 + PB_13, //D54 + // Duplicated pins in order to be aligned with PinMap_ADC + PC_0, //D55/A0 = D5 + PC_1, //D56/A1 = D6 + PC_2, //D57/A2 = D7 + PC_3, //D58/A3 = D8 + PA_0, //D59/A4 = D9 + PA_1, //D60/A5 = D10 + PA_2, //D61/A6 = D11 + PA_3, //D62/A7 = D12 + PA_4, //D63/A8 = D15 + PA_5, //D64/A9 = D16 + PA_6, //D65/A10= D17 + PA_7, //D66/A11= D18 + PC_4, //D67/A12 = D19 + PC_5, //D68/A13 = D20 + PB_0, //D69/A14 = D21 + PB_1 //D70/A15 = D22 +}; + +#ifdef __cplusplus +} +#endif + +// ---------------------------------------------------------------------------- + +#ifdef __cplusplus +extern "C" { +#endif + +/** + * @brief System Clock Configuration + * The system Clock is configured as follow : + * System Clock source = PLL (HSI/2) + * SYSCLK(Hz) = 48000000 + * HCLK(Hz) = 48000000 + * AHB Prescaler = 1 + * APB1 Prescaler = 1 + * HSI Frequency(Hz) = 8000000 + * PREDIV = 1 + * PLLMUL = 12 + * Flash Latency(WS) = 1 + * @param None + * @retval None + */ +WEAK void SystemClock_Config(void) +{ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + + /* No HSE Oscillator on Nucleo, Activate PLL with HSI/2 as source */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI; + RCC_OscInitStruct.HSIState = RCC_HSI_ON; + RCC_OscInitStruct.HSICalibrationValue = 15; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI; + RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV1; + RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL12; + if (HAL_RCC_OscConfig(&RCC_OscInitStruct)!= HAL_OK) + { + /* Initialization Error */ + while(1); + } + + /* Select PLL as system clock source and configure the HCLK, PCLK1 clocks dividers */ + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1); + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; + if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1)!= HAL_OK) + { + /* Initialization Error */ + while(1); + } + + HAL_SYSTICK_Config(HAL_RCC_GetHCLKFreq()/1000); + + HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK); + + /* SysTick_IRQn interrupt configuration */ + HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0); +} + +#ifdef __cplusplus +} +#endif diff --git a/variants/DISCO_F030R8/variant.h b/variants/DISCO_F030R8/variant.h new file mode 100644 index 0000000000..f9448db1a3 --- /dev/null +++ b/variants/DISCO_F030R8/variant.h @@ -0,0 +1,194 @@ +/* + Copyright (c) 2011 Arduino. All right reserved. + + This library is free software; you can redistribute it and/or + modify it under the terms of the GNU Lesser General Public + License as published by the Free Software Foundation; either + version 2.1 of the License, or (at your option) any later version. + + This library is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. + See the GNU Lesser General Public License for more details. + + You should have received a copy of the GNU Lesser General Public + License along with this library; if not, write to the Free Software + Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +*/ + +#ifndef _VARIANT_ARDUINO_STM32_ +#define _VARIANT_ARDUINO_STM32_ + +/*---------------------------------------------------------------------------- + * Headers + *----------------------------------------------------------------------------*/ + +#include "PeripheralPins.h" + +#ifdef __cplusplus +extern "C"{ +#endif // __cplusplus + +/*---------------------------------------------------------------------------- + * Pins + *----------------------------------------------------------------------------*/ +extern const PinName digitalPin[]; + +enum { + //P1 connector Right side (bottom view) + PC13, //D0 + PC14, //D1 + PC15, //D2 + PF0, //D3 + PF1, //D4 + PC0, //D5 + PC1, //D6 + PC2, //D7 + PC3, //D8 + PA0, //D9 + PA1, //D10 + PA2, //D11 + PA3, //D12 + PF4, //D13 + PF5, //D14 + PA4, //D15 + PA5, //D16 + PA6, //D17 + PA7, //D18 + PC4, //D19 + PC5, //D20 + PB0, //D21 + PB1, //D22 + PB2, //D23 + PB10, //D24 + PB11, //D25 + PB12, //D26 + //P2 connector Left side (bottom view) + PB9, //D27 + PB8, //D28 + PB7, //D29 + PB6, //D30 + PB5, //D31 + PB4, //D32 + PB3, //D33 + PD2, //D34 + PC12, //D35 + PC11, //D36 + PC10, //D37 + PA15, //D38 + PA14, //D39 + PF7, //D40 + PF6, //D41 + PA13, //D42 + PA12, //D43 + PA11, //D44 + PA10, //D45 + PA9, //D46 + PA8, //D47 + PC9, //D48 + PC8, //D49 + PC7, //D50 + PC6, //D51 + PB15, //D52 + PB14, //D53 + PB13, //D54 + // Duplicated pins in order to be aligned with PinMap_ADC + PC_0_A, //D55/A0 = D5 + PC_1_A, //D56/A1 = D6 + PC_2_A, //D57/A2 = D7 + PC_3_A, //D58/A3 = D8 + PA_0_A, //D59/A4 = D9 + PA_1_A, //D60/A5 = D10 + PA_2_A, //D61/A6 = D11 + PA_3_A, //D62/A7 = D12 + PA_4_A, //D63/A8 = D15 + PA_5_A, //D64/A9 = D16 + PA_6_A, //D65/A10= D17 + PA_7_A, //D66/A11= D18 + PC_4_A, //D67/A12 = D19 + PC_5_A, //D68/A13 = D20 + PB_0_A, //D69/A14 = D21 + PB_1_A, //D70/A15 = D22 + PEND +}; + +// This must be a literal with the same value as PEND +#define NUM_DIGITAL_PINS 71 +// This must be a literal with a value less than or equal to to MAX_ANALOG_INPUTS +#define NUM_ANALOG_INPUTS 16 +#define NUM_ANALOG_FIRST 55 + +//ADC resolution is 12bits +#define ADC_RESOLUTION 12 + +//PWR resolution +#define PWM_RESOLUTION 8 +#define PWM_FREQUENCY 1000 +#define PWM_MAX_DUTY_CYCLE 255 + +//On-board LED pin number +#define LED_BUILTIN 48 +#define LED_GREEN LED_BUILTIN +#define LED_BLUE 49 + +//On-board user button +#define USER_BTN 9 + + +//SPI definitions +// SPI1 is used +#define PIN_SPI_SS 30 //PB6 +#define PIN_SPI_SS1 31 //PB5 +#define PIN_SPI_SS2 47 //PA8 +#define PIN_SPI_SS3 46 //PA9 +#define PIN_SPI_MOSI 18 //PA7 +#define PIN_SPI_MISO 17 //PA6 +#define PIN_SPI_SCK 16 //PA5 + +//I2C Definitions +// I2C1 is used +#define PIN_WIRE_SDA 27 //PB9 +#define PIN_WIRE_SCL 28 //PB8 + +//Timer Definitions +//Do not use timer used by PWM pins when possible. See PinMap_PWM. +#define TIMER_TONE TIM6 + +//Do not use basic timer: OC is required +#define TIMER_SERVO TIM3 //TODO: advanced-control timers don't work + +// UART Definitions +#define SERIAL_UART_INSTANCE 1 // USART 1 Connected to ST-Link +// Default pin used for 'Serial' instance (ex: ST-Link) +// Mandatory for Firmata +#define PIN_SERIAL_RX 45// PA10 +#define PIN_SERIAL_TX 46 // PA9 + +#ifdef __cplusplus +} // extern "C" +#endif +/*---------------------------------------------------------------------------- + * Arduino objects - C++ only + *----------------------------------------------------------------------------*/ + +#ifdef __cplusplus +// These serial port names are intended to allow libraries and architecture-neutral +// sketches to automatically default to the correct port name for a particular type +// of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN, +// the first hardware serial port whose RX/TX pins are not dedicated to another use. +// +// SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor +// +// SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial +// +// SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library +// +// SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins. +// +// SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX +// pins are NOT connected to anything by default. +#define SERIAL_PORT_MONITOR Serial +#define SERIAL_PORT_HARDWARE Serial +#endif + +#endif /* _VARIANT_ARDUINO_STM32_ */