diff --git a/examples/SARA-R5_Example1_GNSS_GPRMC/SARA-R5_Example1_GNSS_GPRMC.ino b/examples/SARA-R5_Example1_GNSS_GPRMC/SARA-R5_Example1_GNSS_GPRMC.ino
index a45c51a..2143453 100644
--- a/examples/SARA-R5_Example1_GNSS_GPRMC/SARA-R5_Example1_GNSS_GPRMC.ino
+++ b/examples/SARA-R5_Example1_GNSS_GPRMC/SARA-R5_Example1_GNSS_GPRMC.ino
@@ -40,12 +40,6 @@ SARA_R5 mySARA;
 // Change the pin number if required.
 //SARA_R5 mySARA(34);
 
-// If you're using the MicroMod Asset Tracker then we need to define which pin controls the active antenna power for the GNSS.
-// If you're using the MicroMod Artemis Processor Board, the pin name is G6 which is connected to pin D14.
-// Change the pin number if required.
-//const int antennaPowerEnablePin = 14; // Uncomment this line to define the pin number for the antenna power enable
-const int antennaPowerEnablePin = -1; // Uncomment this line if your board does not have an antenna power enable
-
 PositionData gps;
 SpeedData spd;
 ClockData clk;
@@ -86,7 +80,9 @@ void setup()
   }
 
   // Enable power for the GNSS active antenna
-  enableGNSSAntennaPower();
+  // On the MicroMod Asset Tracker, the SARA GPIO2 pin is used to control power for the antenna.
+  // We need to pull GPIO2 (Pin 23) high to enable the power.
+  mySARA.setGpioMode(mySARA.GPIO2, mySARA.GPIO_OUTPUT, 1);
 
   // From the u-blox SARA-R5 Positioning Implementation Application Note UBX-20012413 - R01
   // To enable the PPS output we need to:
@@ -147,22 +143,3 @@ void printGPS(void)
   Serial.println("Mode: " + String(gps.mode));
   Serial.println();
 }
-
-// Disable power for the GNSS active antenna
-void disableGNSSAntennaPower()
-{
-  if (antennaPowerEnablePin >= 0)
-  {
-    pinMode(antennaPowerEnablePin, OUTPUT);
-    digitalWrite(antennaPowerEnablePin, LOW);
-  }
-}
-// Enable power for the GNSS active antenna
-void enableGNSSAntennaPower()
-{
-  if (antennaPowerEnablePin >= 0)
-  {
-    pinMode(antennaPowerEnablePin, OUTPUT);
-    digitalWrite(antennaPowerEnablePin, HIGH);
-  }
-}
diff --git a/src/SparkFun_u-blox_SARA-R5_Arduino_Library.cpp b/src/SparkFun_u-blox_SARA-R5_Arduino_Library.cpp
index 879f5de..f96d63a 100644
--- a/src/SparkFun_u-blox_SARA-R5_Arduino_Library.cpp
+++ b/src/SparkFun_u-blox_SARA-R5_Arduino_Library.cpp
@@ -1878,16 +1878,20 @@ SARA_R5_error_t SARA_R5::setBaud(unsigned long baud)
 }
 
 SARA_R5_error_t SARA_R5::setGpioMode(SARA_R5_gpio_t gpio,
-                                           SARA_R5_gpio_mode_t mode)
+                                SARA_R5_gpio_mode_t mode, int value)
 {
     SARA_R5_error_t err;
     char *command;
 
     // Example command: AT+UGPIOC=16,2
-    command = sara_r5_calloc_char(strlen(SARA_R5_COMMAND_GPIO) + 7);
+    // Example command: AT+UGPIOC=23,0,1
+    command = sara_r5_calloc_char(strlen(SARA_R5_COMMAND_GPIO) + 10);
     if (command == NULL)
         return SARA_R5_ERROR_OUT_OF_MEMORY;
-    sprintf(command, "%s=%d,%d", SARA_R5_COMMAND_GPIO, gpio, mode);
+    if (mode == GPIO_OUTPUT)
+        sprintf(command, "%s=%d,%d,%d", SARA_R5_COMMAND_GPIO, gpio, mode, value);
+    else
+        sprintf(command, "%s=%d,%d", SARA_R5_COMMAND_GPIO, gpio, mode);
 
     err = sendCommandWithResponse(command, SARA_R5_RESPONSE_OK,
                                   NULL, SARA_R5_10_SEC_TIMEOUT);
diff --git a/src/SparkFun_u-blox_SARA-R5_Arduino_Library.h b/src/SparkFun_u-blox_SARA-R5_Arduino_Library.h
index f28ed84..c21191e 100644
--- a/src/SparkFun_u-blox_SARA-R5_Arduino_Library.h
+++ b/src/SparkFun_u-blox_SARA-R5_Arduino_Library.h
@@ -563,7 +563,7 @@ class SARA_R5 : public Print
         KHZ_32768_OUT = 32,
         PAD_DISABLED = 255
     } SARA_R5_gpio_mode_t;
-    SARA_R5_error_t setGpioMode(SARA_R5_gpio_t gpio, SARA_R5_gpio_mode_t mode);
+    SARA_R5_error_t setGpioMode(SARA_R5_gpio_t gpio, SARA_R5_gpio_mode_t mode, int value = 0);
     SARA_R5_gpio_mode_t getGpioMode(SARA_R5_gpio_t gpio);
 
     // IP Transport Layer