SparkFun_Ublox_Arduino_Library.cpp

/*
	This is a library written for the Ublox ZED-F9P and NEO-M8P-2
	SparkFun sells these at its website: www.sparkfun.com
	Do you like this library? Help support SparkFun. Buy a board!
	https://www.sparkfun.com/products/15136
	https://www.sparkfun.com/products/15005
	https://www.sparkfun.com/products/15733
	https://www.sparkfun.com/products/15193
	https://www.sparkfun.com/products/15210

	Written by Nathan Seidle @ SparkFun Electronics, September 6th, 2018

	This library handles configuring and handling the responses
	from a Ublox GPS module. Works with most modules from Ublox including
	the Zed-F9P, NEO-M8P-2, NEO-M9N, ZOE-M8Q, SAM-M8Q, and many others.

	https://github.com/sparkfun/SparkFun_Ublox_Arduino_Library

	Development environment specifics:
	Arduino IDE 1.8.5

	SparkFun code, firmware, and software is released under the MIT License(http://opensource.org/licenses/MIT).
	The MIT License (MIT)
	Copyright (c) 2016 SparkFun Electronics
	Permission is hereby granted, free of charge, to any person obtaining a copy of this software and
	associated documentation files (the "Software"), to deal in the Software without restriction,
	including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense,
	and/or sell copies of the Software, and to permit persons to whom the Software is furnished to
	do so, subject to the following conditions:

	The above copyright notice and this permission notice shall be included in all copies or substantial
	portions of the Software.

	THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT
	NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
	IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
	WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
	SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
*/

#include "SparkFun_Ublox_Arduino_Library.h"

SFE_UBLOX_GPS::SFE_UBLOX_GPS(void)
{
  // Constructor
  currentGeofenceParams.numFences = 0; // Zero the number of geofences currently in use
  moduleQueried.versionNumber = false;

  if (checksumFailurePin >= 0)
  {
    pinMode((uint8_t)checksumFailurePin, OUTPUT);
    digitalWrite((uint8_t)checksumFailurePin, HIGH);
  }
}

//Initialize the Serial port
boolean SFE_UBLOX_GPS::begin(TwoWire &wirePort, uint8_t deviceAddress)
{
  commType = COMM_TYPE_I2C;
  _i2cPort = &wirePort; //Grab which port the user wants us to use

  //We expect caller to begin their I2C port, with the speed of their choice external to the library
  //But if they forget, we start the hardware here.

  //We're moving away from the practice of starting Wire hardware in a library. This is to avoid cross platform issues.
  //ie, there are some platforms that don't handle multiple starts to the wire hardware. Also, every time you start the wire
  //hardware the clock speed reverts back to 100kHz regardless of previous Wire.setClocks().
  //_i2cPort->begin();

  _gpsI2Caddress = deviceAddress; //Store the I2C address from user

  return (isConnected());
}

//Initialize the Serial port
boolean SFE_UBLOX_GPS::begin(Stream &serialPort)
{
  commType = COMM_TYPE_SERIAL;
  _serialPort = &serialPort; //Grab which port the user wants us to use

  return (isConnected());
}

//Enable or disable the printing of sent/response HEX values.
//Use this in conjunction with 'Transport Logging' from the Universal Reader Assistant to see what they're doing that we're not
void SFE_UBLOX_GPS::enableDebugging(Stream &debugPort)
{
  _debugSerial = &debugPort; //Grab which port the user wants us to use for debugging

  _printDebug = true; //Should we print the commands we send? Good for debugging
}
void SFE_UBLOX_GPS::disableDebugging(void)
{
  _printDebug = false; //Turn off extra print statements
}

//Safely print messages
void SFE_UBLOX_GPS::debugPrint(char *message)
{
  if (_printDebug == true)
  {
    _debugSerial->print(message);
  }
}
//Safely print messages
void SFE_UBLOX_GPS::debugPrintln(char *message)
{
  if (_printDebug == true)
  {
    _debugSerial->println(message);
  }
}

const char *SFE_UBLOX_GPS::statusString(sfe_ublox_status_e stat)
{
  switch (stat)
  {
  case SFE_UBLOX_STATUS_SUCCESS:
    return "Success";
    break;
  case SFE_UBLOX_STATUS_FAIL:
    return "General Failure";
    break;
  case SFE_UBLOX_STATUS_CRC_FAIL:
    return "CRC Fail";
    break;
  case SFE_UBLOX_STATUS_TIMEOUT:
    return "Timeout";
    break;
  case SFE_UBLOX_STATUS_COMMAND_UNKNOWN:
    return "Command Unknown";
    break;
  case SFE_UBLOX_STATUS_OUT_OF_RANGE:
    return "Out of range";
    break;
  case SFE_UBLOX_STATUS_INVALID_ARG:
    return "Invalid Arg";
    break;
  case SFE_UBLOX_STATUS_INVALID_OPERATION:
    return "Invalid operation";
    break;
  case SFE_UBLOX_STATUS_MEM_ERR:
    return "Memory Error";
    break;
  case SFE_UBLOX_STATUS_HW_ERR:
    return "Hardware Error";
    break;
  case SFE_UBLOX_STATUS_DATA_SENT:
    return "Data Sent";
    break;
  case SFE_UBLOX_STATUS_DATA_RECEIVED:
    return "Data Received";
    break;
  case SFE_UBLOX_STATUS_I2C_COMM_FAILURE:
    return "I2C Comm Failure";
    break;
  default:
    return "Unknown Status";
    break;
  }
  return "None";
}

void SFE_UBLOX_GPS::factoryReset()
{
  // Copy default settings to permanent
  // Note: this does not load the permanent configuration into the current configuration. Calling factoryDefault() will do that.
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_CFG;
  packetCfg.len = 13;
  packetCfg.startingSpot = 0;
  for (uint8_t i = 0; i < 4; i++)
  {
    payloadCfg[0 + i] = 0xff; // clear mask: copy default config to permanent config
    payloadCfg[4 + i] = 0x00; // save mask: don't save current to permanent
    payloadCfg[8 + i] = 0x00; // load mask: don't copy permanent config to current
  }
  payloadCfg[12] = 0xff;     // all forms of permanent memory
  sendCommand(packetCfg, 0); // don't expect ACK
  hardReset();               // cause factory default config to actually be loaded and used cleanly
}

void SFE_UBLOX_GPS::hardReset()
{
  // Issue hard reset
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_RST;
  packetCfg.len = 4;
  packetCfg.startingSpot = 0;
  payloadCfg[0] = 0xff;      // cold start
  payloadCfg[1] = 0xff;      // cold start
  payloadCfg[2] = 0;         // 0=HW reset
  payloadCfg[3] = 0;         // reserved
  sendCommand(packetCfg, 0); // don't expect ACK
}

//Changes the serial baud rate of the Ublox module, can't return success/fail 'cause ACK from modem
//is lost due to baud rate change
void SFE_UBLOX_GPS::setSerialRate(uint32_t baudrate, uint8_t uartPort, uint16_t maxWait)
{
  //Get the current config values for the UART port
  getPortSettings(uartPort, maxWait); //This will load the payloadCfg array with current port settings

  if (_printDebug == true)
  {
    _debugSerial->print(F("Current baud rate: "));
    _debugSerial->println(((uint32_t)payloadCfg[10] << 16) | ((uint32_t)payloadCfg[9] << 8) | payloadCfg[8]);
  }

  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_PRT;
  packetCfg.len = 20;
  packetCfg.startingSpot = 0;

  //payloadCfg is now loaded with current bytes. Change only the ones we need to
  payloadCfg[8] = baudrate;
  payloadCfg[9] = baudrate >> 8;
  payloadCfg[10] = baudrate >> 16;
  payloadCfg[11] = baudrate >> 24;

  if (_printDebug == true)
  {
    _debugSerial->print(F("New baud rate:"));
    _debugSerial->println(((uint32_t)payloadCfg[10] << 16) | ((uint32_t)payloadCfg[9] << 8) | payloadCfg[8]);
  }

  sfe_ublox_status_e retVal = sendCommand(packetCfg, maxWait);
  if (_printDebug == true)
  {
    _debugSerial->print(F("setSerialRate: sendCommand returned: "));
    _debugSerial->println(statusString(retVal));
  }
}

//Changes the I2C address that the Ublox module responds to
//0x42 is the default but can be changed with this command
boolean SFE_UBLOX_GPS::setI2CAddress(uint8_t deviceAddress, uint16_t maxWait)
{
  //Get the current config values for the I2C port
  getPortSettings(COM_PORT_I2C, maxWait); //This will load the payloadCfg array with current port settings

  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_PRT;
  packetCfg.len = 20;
  packetCfg.startingSpot = 0;

  //payloadCfg is now loaded with current bytes. Change only the ones we need to
  payloadCfg[4] = deviceAddress << 1; //DDC mode LSB

  if (sendCommand(packetCfg, maxWait) == SFE_UBLOX_STATUS_DATA_SENT) // We are only expecting an ACK
  {
    //Success! Now change our internal global.
    _gpsI2Caddress = deviceAddress; //Store the I2C address from user
    return (true);
  }
  return (false);
}

//Want to see the NMEA messages on the Serial port? Here's how
void SFE_UBLOX_GPS::setNMEAOutputPort(Stream &nmeaOutputPort)
{
  _nmeaOutputPort = &nmeaOutputPort; //Store the port from user
}

//Called regularly to check for available bytes on the user' specified port
boolean SFE_UBLOX_GPS::checkUblox()
{
  if (commType == COMM_TYPE_I2C)
    return (checkUbloxI2C());
  else if (commType == COMM_TYPE_SERIAL)
    return (checkUbloxSerial());
  return false;
}

//Polls I2C for data, passing any new bytes to process()
//Returns true if new bytes are available
boolean SFE_UBLOX_GPS::checkUbloxI2C()
{
  if (millis() - lastCheck >= i2cPollingWait)
  {
    //Get the number of bytes available from the module
    uint16_t bytesAvailable = 0;
    _i2cPort->beginTransmission(_gpsI2Caddress);
    _i2cPort->write(0xFD);                     //0xFD (MSB) and 0xFE (LSB) are the registers that contain number of bytes available
    if (_i2cPort->endTransmission(false) != 0) //Send a restart command. Do not release bus.
      return (false);                          //Sensor did not ACK

    _i2cPort->requestFrom((uint8_t)_gpsI2Caddress, (uint8_t)2);
    if (_i2cPort->available())
    {
      uint8_t msb = _i2cPort->read();
      uint8_t lsb = _i2cPort->read();
      if (lsb == 0xFF)
      {
        //I believe this is a Ublox bug. Device should never present an 0xFF.
        if (_printDebug == true)
        {
          _debugSerial->println(F("checkUbloxI2C: Ublox bug, no bytes available"));
        }
        if (checksumFailurePin >= 0)
        {
          digitalWrite((uint8_t)checksumFailurePin, LOW);
          delay(10);
          digitalWrite((uint8_t)checksumFailurePin, HIGH);
        }
        lastCheck = millis(); //Put off checking to avoid I2C bus traffic
        return (false);
      }
      bytesAvailable = (uint16_t)msb << 8 | lsb;
    }

    if (bytesAvailable == 0)
    {
      if (_printDebug == true)
      {
        _debugSerial->println(F("checkUbloxI2C: OK, zero bytes available"));
      }
      lastCheck = millis(); //Put off checking to avoid I2C bus traffic
      return (false);
    }

    //Check for undocumented bit error. We found this doing logic scans.
    //This error is rare but if we incorrectly interpret the first bit of the two 'data available' bytes as 1
    //then we have far too many bytes to check. May be related to I2C setup time violations: https://github.com/sparkfun/SparkFun_Ublox_Arduino_Library/issues/40
    if (bytesAvailable & ((uint16_t)1 << 15))
    {
      //Clear the MSbit
      bytesAvailable &= ~((uint16_t)1 << 15);

      if (_printDebug == true)
      {
        _debugSerial->print(F("checkUbloxI2C: Bytes available error:"));
        _debugSerial->println(bytesAvailable);
        if (checksumFailurePin >= 0)
        {
          digitalWrite((uint8_t)checksumFailurePin, LOW);
          delay(10);
          digitalWrite((uint8_t)checksumFailurePin, HIGH);
        }
      }
    }

    if (bytesAvailable > 100)
    {
      if (_printDebug == true)
      {
        _debugSerial->print(F("checkUbloxI2C: Large packet of "));
        _debugSerial->print(bytesAvailable);
        _debugSerial->println(F(" bytes received"));
      }
    }
    else
    {
      if (_printDebug == true)
      {
        _debugSerial->print(F("checkUbloxI2C: Reading "));
        _debugSerial->print(bytesAvailable);
        _debugSerial->println(F(" bytes"));
      }
    }

    while (bytesAvailable)
    {
      _i2cPort->beginTransmission(_gpsI2Caddress);
      _i2cPort->write(0xFF);                     //0xFF is the register to read data from
      if (_i2cPort->endTransmission(false) != 0) //Send a restart command. Do not release bus.
        return (false);                          //Sensor did not ACK

      //Limit to 32 bytes or whatever the buffer limit is for given platform
      uint16_t bytesToRead = bytesAvailable;
      if (bytesToRead > I2C_BUFFER_LENGTH)
        bytesToRead = I2C_BUFFER_LENGTH;

    TRY_AGAIN:

      _i2cPort->requestFrom((uint8_t)_gpsI2Caddress, (uint8_t)bytesToRead);
      if (_i2cPort->available())
      {
        for (uint16_t x = 0; x < bytesToRead; x++)
        {
          uint8_t incoming = _i2cPort->read(); //Grab the actual character

          //Check to see if the first read is 0x7F. If it is, the module is not ready
          //to respond. Stop, wait, and try again
          if (x == 0)
          {
            if (incoming == 0x7F)
            {
              if (_printDebug == true)
              {
                _debugSerial->println(F("checkUbloxU2C: Ublox error, module not ready with data"));
              }
              delay(5); //In logic analyzation, the module starting responding after 1.48ms
              if (checksumFailurePin >= 0)
              {
                digitalWrite((uint8_t)checksumFailurePin, LOW);
                delay(10);
                digitalWrite((uint8_t)checksumFailurePin, HIGH);
              }
              goto TRY_AGAIN;
            }
          }

          process(incoming); //Process this valid character
        }
      }
      else
        return (false); //Sensor did not respond

      bytesAvailable -= bytesToRead;
    }
  }

  return (true);

} //end checkUbloxI2C()

//Checks Serial for data, passing any new bytes to process()
boolean SFE_UBLOX_GPS::checkUbloxSerial()
{
  while (_serialPort->available())
  {
    process(_serialPort->read());
  }
  return (true);

} //end checkUbloxSerial()

//Processes NMEA and UBX binary sentences one byte at a time
//Take a given byte and file it into the proper array
void SFE_UBLOX_GPS::process(uint8_t incoming)
{
  if (currentSentence == NONE || currentSentence == NMEA)
  {
    if (incoming == 0xB5) //UBX binary frames start with 0xB5, aka μ
    {
      //This is the start of a binary sentence. Reset flags.
      //We still don't know the response class
      ubxFrameCounter = 0;

      rollingChecksumA = 0; //Reset our rolling checksums
      rollingChecksumB = 0;

      currentSentence = UBX;
    }
    else if (incoming == '$')
    {
      currentSentence = NMEA;
    }
    else if (incoming == 0xD3) //RTCM frames start with 0xD3
    {
      rtcmFrameCounter = 0;
      currentSentence = RTCM;
    }
    else
    {
      //This character is unknown or we missed the previous start of a sentence
    }
  }

  //Depending on the sentence, pass the character to the individual processor
  if (currentSentence == UBX)
  {
    //Decide what type of response this is
    if (ubxFrameCounter == 0 && incoming != 0xB5)      //ISO 'μ'
      currentSentence = NONE;                          //Something went wrong. Reset.
    else if (ubxFrameCounter == 1 && incoming != 0x62) //ASCII 'b'
      currentSentence = NONE;                          //Something went wrong. Reset.
    else if (ubxFrameCounter == 2)                     //Class
    {
      //We can now identify the type of response
      if (incoming == UBX_CLASS_ACK)
      {
        packetAck.counter = 0;
        packetAck.valid = SFE_UBLOX_PACKET_VALIDITY_NOT_DEFINED;
        ubxFrameClass = CLASS_ACK;
      }
      else
      {
        packetCfg.counter = 0;
        packetCfg.valid = SFE_UBLOX_PACKET_VALIDITY_NOT_DEFINED;
        ubxFrameClass = CLASS_NOT_AN_ACK;
      }
    }

    ubxFrameCounter++;

    //Depending on this frame's class, pass different structs and payload arrays
    if (ubxFrameClass == CLASS_ACK)
      processUBX(incoming, &packetAck);
    else if (ubxFrameClass == CLASS_NOT_AN_ACK)
      processUBX(incoming, &packetCfg);
  }
  else if (currentSentence == NMEA)
  {
    processNMEA(incoming); //Process each NMEA character
  }
  else if (currentSentence == RTCM)
  {
    processRTCMframe(incoming); //Deal with RTCM bytes
  }
}

//This is the default or generic NMEA processor. We're only going to pipe the data to serial port so we can see it.
//User could overwrite this function to pipe characters to nmea.process(c) of tinyGPS or MicroNMEA
//Or user could pipe each character to a buffer, radio, etc.
void SFE_UBLOX_GPS::processNMEA(char incoming)
{
  //If user has assigned an output port then pipe the characters there
  if (_nmeaOutputPort != NULL)
    _nmeaOutputPort->write(incoming); //Echo this byte to the serial port
}

//We need to be able to identify an RTCM packet and then the length
//so that we know when the RTCM message is completely received and we then start
//listening for other sentences (like NMEA or UBX)
//RTCM packet structure is very odd. I never found RTCM STANDARD 10403.2 but
//http://d1.amobbs.com/bbs_upload782111/files_39/ourdev_635123CK0HJT.pdf is good
//https://dspace.cvut.cz/bitstream/handle/10467/65205/F3-BP-2016-Shkalikava-Anastasiya-Prenos%20polohove%20informace%20prostrednictvim%20datove%20site.pdf?sequence=-1
//Lead me to: https://forum.u-blox.com/index.php/4348/how-to-read-rtcm-messages-from-neo-m8p
//RTCM 3.2 bytes look like this:
//Byte 0: Always 0xD3
//Byte 1: 6-bits of zero
//Byte 2: 10-bits of length of this packet including the first two-ish header bytes, + 6.
//byte 3 + 4 bits: Msg type 12 bits
//Example: D3 00 7C 43 F0 ... / 0x7C = 124+6 = 130 bytes in this packet, 0x43F = Msg type 1087
void SFE_UBLOX_GPS::processRTCMframe(uint8_t incoming)
{
  if (rtcmFrameCounter == 1)
  {
    rtcmLen = (incoming & 0x03) << 8; //Get the last two bits of this byte. Bits 8&9 of 10-bit length
  }
  else if (rtcmFrameCounter == 2)
  {
    rtcmLen |= incoming; //Bits 0-7 of packet length
    rtcmLen += 6;        //There are 6 additional bytes of what we presume is header, msgType, CRC, and stuff
  }
  /*else if (rtcmFrameCounter == 3)
  {
    rtcmMsgType = incoming << 4; //Message Type, MS 4 bits
  }
  else if (rtcmFrameCounter == 4)
  {
    rtcmMsgType |= (incoming >> 4); //Message Type, bits 0-7
  }*/

  rtcmFrameCounter++;

  processRTCM(incoming); //Here is where we expose this byte to the user

  if (rtcmFrameCounter == rtcmLen)
  {
    //We're done!
    currentSentence = NONE; //Reset and start looking for next sentence type
  }
}

//This function is called for each byte of an RTCM frame
//Ths user can overwrite this function and process the RTCM frame as they please
//Bytes can be piped to Serial or other interface. The consumer could be a radio or the internet (Ntrip broadcaster)
void SFE_UBLOX_GPS::processRTCM(uint8_t incoming)
{
  //Radio.sendReliable((String)incoming); //An example of passing this byte to a radio

  //_debugSerial->write(incoming); //An example of passing this byte out the serial port

  //Debug printing
  //  _debugSerial->print(F(" "));
  //  if(incoming < 0x10) _debugSerial->print(F("0"));
  //  if(incoming < 0x10) _debugSerial->print(F("0"));
  //  _debugSerial->print(incoming, HEX);
  //  if(rtcmFrameCounter % 16 == 0) _debugSerial->println();
}

//Given a character, file it away into the uxb packet structure
//Set valid to VALID or NOT_VALID once sentence is completely received and passes or fails CRC
//The payload portion of the packet can be 100s of bytes but the max array
//size is roughly 64 bytes. startingSpot can be set so we only record
//a subset of bytes within a larger packet.
void SFE_UBLOX_GPS::processUBX(uint8_t incoming, ubxPacket *incomingUBX)
{
  //Add all incoming bytes to the rolling checksum
  //Stop at len+4 as this is the checksum bytes to that should not be added to the rolling checksum
  if (incomingUBX->counter < incomingUBX->len + 4)
    addToChecksum(incoming);

  if (incomingUBX->counter == 0)
  {
    incomingUBX->cls = incoming;
  }
  else if (incomingUBX->counter == 1)
  {
    incomingUBX->id = incoming;
  }
  else if (incomingUBX->counter == 2) //Len LSB
  {
    incomingUBX->len = incoming;
  }
  else if (incomingUBX->counter == 3) //Len MSB
  {
    incomingUBX->len |= incoming << 8;
  }
  else if (incomingUBX->counter == incomingUBX->len + 4) //ChecksumA
  {
    incomingUBX->checksumA = incoming;
  }
  else if (incomingUBX->counter == incomingUBX->len + 5) //ChecksumB
  {
    incomingUBX->checksumB = incoming;

    currentSentence = NONE; //We're done! Reset the sentence to being looking for a new start char

    //Validate this sentence
    if (incomingUBX->checksumA == rollingChecksumA && incomingUBX->checksumB == rollingChecksumB)
    {
      incomingUBX->valid = SFE_UBLOX_PACKET_VALIDITY_VALID;

      if (_printDebug == true)
      {
        _debugSerial->print(F("Incoming: Size: "));
        _debugSerial->print(incomingUBX->len);
        _debugSerial->print(F(" Received: "));
        printPacket(incomingUBX);

        if (packetCfg.valid == SFE_UBLOX_PACKET_VALIDITY_VALID)
        {
          if (_printDebug == true)
          {
            _debugSerial->println(F("packetCfg now valid"));
          }
        }
        if (packetAck.valid == SFE_UBLOX_PACKET_VALIDITY_VALID)
        {
          if (_printDebug == true)
          {
            _debugSerial->println(F("packetAck now valid"));
          }
        }
      }

      processUBXpacket(incomingUBX); //We've got a valid packet, now do something with it
    }
    else  // Checksum failure
    {
      incomingUBX->valid = SFE_UBLOX_PACKET_VALIDITY_NOT_VALID;

      if (_printDebug == true)
      {
        //Drive an external pin to allow for easier logic analyzation
        if (checksumFailurePin >= 0)
        {
          digitalWrite((uint8_t)checksumFailurePin, LOW);
          delay(10);
          digitalWrite((uint8_t)checksumFailurePin, HIGH);
        }

        _debugSerial->print(F("Checksum failed:"));
        _debugSerial->print(F(" checksumA: "));
        _debugSerial->print(incomingUBX->checksumA);
        _debugSerial->print(F(" checksumB: "));
        _debugSerial->print(incomingUBX->checksumB);

        _debugSerial->print(F(" rollingChecksumA: "));
        _debugSerial->print(rollingChecksumA);
        _debugSerial->print(F(" rollingChecksumB: "));
        _debugSerial->print(rollingChecksumB);
        _debugSerial->println();

        _debugSerial->print(F("Failed  : "));
        _debugSerial->print(F("Size: "));
        _debugSerial->print(incomingUBX->len);
        _debugSerial->print(F(" Received: "));
        printPacket(incomingUBX);
      }
    }
  }
  else //Load this byte into the payload array
  {
    //If a UBX_NAV_PVT packet comes in asynchronously, we need to fudge the startingSpot
    uint16_t startingSpot = incomingUBX->startingSpot;
    if (incomingUBX->cls == UBX_CLASS_NAV && incomingUBX->id == UBX_NAV_PVT)
      startingSpot = 0;
    //Begin recording if counter goes past startingSpot
    if ((incomingUBX->counter - 4) >= startingSpot)
    {
      //Check to see if we have room for this byte
      if (((incomingUBX->counter - 4) - startingSpot) < MAX_PAYLOAD_SIZE)         //If counter = 208, starting spot = 200, we're good to record.
        incomingUBX->payload[incomingUBX->counter - 4 - startingSpot] = incoming; //Store this byte into payload array
    }
  }

  incomingUBX->counter++;
  if (incomingUBX->counter == MAX_PAYLOAD_SIZE)
  {
    //Something has gone very wrong
    currentSentence = NONE; //Reset the sentence to being looking for a new start char
    if (_printDebug == true)
    {
      _debugSerial->println(F("processUBX: counter hit MAX_PAYLOAD_SIZE"));
    }
  }
}

//Once a packet has been received and validated, identify this packet's class/id and update internal flags
void SFE_UBLOX_GPS::processUBXpacket(ubxPacket *msg)
{
  switch (msg->cls)
  {
  case UBX_CLASS_ACK:
    //We don't want to store ACK packets, just set commandAck flag
    if (msg->id == UBX_ACK_ACK && msg->payload[0] == packetCfg.cls && msg->payload[1] == packetCfg.id)
    {
      //The ack we just received matched the CLS/ID of last packetCfg sent (or received)
      if (_printDebug == true)
      {
        _debugSerial->println(F("UBX ACK: Command sent/ack'd successfully"));
      }
      commandAck = UBX_ACK_ACK;
    }
    else if (msg->id == UBX_ACK_NACK && msg->payload[0] == packetCfg.cls && msg->payload[1] == packetCfg.id)
    {
      //The ack we just received matched the CLS/ID of last packetCfg sent
      if (_printDebug == true)
      {
        _debugSerial->println(F("UBX ACK: Not-Acknowledged"));
      }
      commandAck = UBX_ACK_NACK;
    }
    break;

  case UBX_CLASS_NAV:
    if (msg->id == UBX_NAV_PVT && msg->len == 92)
    {
      //Parse various byte fields into global vars
      constexpr int startingSpot = 0; //fixed value used in processUBX

      timeOfWeek = extractLong(0);
      gpsMillisecond = extractLong(0) % 1000; //Get last three digits of iTOW
      gpsYear = extractInt(4);
      gpsMonth = extractByte(6);
      gpsDay = extractByte(7);
      gpsHour = extractByte(8);
      gpsMinute = extractByte(9);
      gpsSecond = extractByte(10);
      gpsNanosecond = extractLong(16); //Includes milliseconds

      fixType = extractByte(20 - startingSpot);
      carrierSolution = extractByte(21 - startingSpot) >> 6; //Get 6th&7th bits of this byte
      SIV = extractByte(23 - startingSpot);
      longitude = extractLong(24 - startingSpot);
      latitude = extractLong(28 - startingSpot);
      altitude = extractLong(32 - startingSpot);
      altitudeMSL = extractLong(36 - startingSpot);
      groundSpeed = extractLong(60 - startingSpot);
      headingOfMotion = extractLong(64 - startingSpot);
      pDOP = extractInt(76 - startingSpot);

      //Mark all datums as fresh (not read before)
      moduleQueried.gpsiTOW = true;
      moduleQueried.gpsYear = true;
      moduleQueried.gpsMonth = true;
      moduleQueried.gpsDay = true;
      moduleQueried.gpsHour = true;
      moduleQueried.gpsMinute = true;
      moduleQueried.gpsSecond = true;
      moduleQueried.gpsNanosecond = true;

      moduleQueried.all = true;
      moduleQueried.longitude = true;
      moduleQueried.latitude = true;
      moduleQueried.altitude = true;
      moduleQueried.altitudeMSL = true;
      moduleQueried.SIV = true;
      moduleQueried.fixType = true;
      moduleQueried.carrierSolution = true;
      moduleQueried.groundSpeed = true;
      moduleQueried.headingOfMotion = true;
      moduleQueried.pDOP = true;
    }
    else if (msg->id == UBX_NAV_HPPOSLLH && msg->len == 36)
    {
      timeOfWeek = extractLong(4);
      highResLongitude = extractLong(8);
      highResLatitude = extractLong(12);
      elipsoid = extractLong(16);
      meanSeaLevel = extractLong(20);
      highResLongitudeHp = extractSignedChar(24);
      highResLatitudeHp = extractSignedChar(25);
      elipsoidHp = extractSignedChar(26);
      meanSeaLevelHp = extractSignedChar(27);
      horizontalAccuracy = extractLong(28);
      verticalAccuracy = extractLong(32);

      highResModuleQueried.all = true;
      highResModuleQueried.highResLatitude = true;
      highResModuleQueried.highResLatitudeHp = true;
      highResModuleQueried.highResLongitude = true;
      highResModuleQueried.highResLongitudeHp = true;
      highResModuleQueried.elipsoid = true;
      highResModuleQueried.elipsoidHp = true;
      highResModuleQueried.meanSeaLevel = true;
      highResModuleQueried.meanSeaLevelHp = true;
      highResModuleQueried.geoidSeparation = true;
      highResModuleQueried.horizontalAccuracy = true;
      highResModuleQueried.verticalAccuracy = true;
      moduleQueried.gpsiTOW = true; // this can arrive via HPPOS too.

      if (_printDebug == true)
      {
        _debugSerial->print(F("Sec: "));
        _debugSerial->print(((float)extractLong(4)) / 1000.0f);
        _debugSerial->print(F(" "));
        _debugSerial->print(F("LON: "));
        _debugSerial->print(((float)(int32_t)extractLong(8)) / 10000000.0f);
        _debugSerial->print(F(" "));
        _debugSerial->print(F("LAT: "));
        _debugSerial->print(((float)(int32_t)extractLong(12)) / 10000000.0f);
        _debugSerial->print(F(" "));
        _debugSerial->print(F("ELI M: "));
        _debugSerial->print(((float)(int32_t)extractLong(16)) / 1000.0f);
        _debugSerial->print(F(" "));
        _debugSerial->print(F("MSL M: "));
        _debugSerial->print(((float)(int32_t)extractLong(20)) / 1000.0f);
        _debugSerial->print(F(" "));
        _debugSerial->print(F("LON HP: "));
        _debugSerial->print(extractSignedChar(24));
        _debugSerial->print(F(" "));
        _debugSerial->print(F("LAT HP: "));
        _debugSerial->print(extractSignedChar(25));
        _debugSerial->print(F(" "));
        _debugSerial->print(F("ELI HP: "));
        _debugSerial->print(extractSignedChar(26));
        _debugSerial->print(F(" "));
        _debugSerial->print(F("MSL HP: "));
        _debugSerial->print(extractSignedChar(27));
        _debugSerial->print(F(" "));
        _debugSerial->print(F("HA 2D M: "));
        _debugSerial->print(((float)(int32_t)extractLong(28)) / 10000.0f);
        _debugSerial->print(F(" "));
        _debugSerial->print(F("VERT M: "));
        _debugSerial->println(((float)(int32_t)extractLong(32)) / 10000.0f);
      }
    }
    break;
  }
}

//Given a packet and payload, send everything including CRC bytes via I2C port
sfe_ublox_status_e SFE_UBLOX_GPS::sendCommand(ubxPacket outgoingUBX, uint16_t maxWait)
{
  sfe_ublox_status_e retVal = SFE_UBLOX_STATUS_SUCCESS;

  calcChecksum(&outgoingUBX); //Sets checksum A and B bytes of the packet

  if (_printDebug == true)
  {
    _debugSerial->print(F("\nSending: "));
    printPacket(&outgoingUBX);
  }

  if (commType == COMM_TYPE_I2C)
  {
    retVal = sendI2cCommand(outgoingUBX, maxWait);
    if (retVal != SFE_UBLOX_STATUS_SUCCESS)
    {
      if (_printDebug == true)
      {
        _debugSerial->println(F("Send I2C Command failed"));
      }
      return retVal;
    }
  }
  else if (commType == COMM_TYPE_SERIAL)
  {
    sendSerialCommand(outgoingUBX);
  }

  if (maxWait > 0)
  {
    //Depending on what we just sent, either we need to look for an ACK or not
    if (outgoingUBX.cls == UBX_CLASS_CFG)
    {
      if (_printDebug == true)
      {
        _debugSerial->println(F("sendCommand: Waiting for ACK response"));
      }
      retVal = waitForACKResponse(outgoingUBX.cls, outgoingUBX.id, maxWait); //Wait for Ack response
    }
    else
    {
      if (_printDebug == true)
      {
        _debugSerial->println(F("sendCommand: Waiting for No ACK response"));
      }
      retVal = waitForNoACKResponse(outgoingUBX.cls, outgoingUBX.id, maxWait); //Wait for Ack response
    }
  }
  return retVal;
}

//Returns false if sensor fails to respond to I2C traffic
sfe_ublox_status_e SFE_UBLOX_GPS::sendI2cCommand(ubxPacket outgoingUBX, uint16_t maxWait)
{
  //Point at 0xFF data register
  _i2cPort->beginTransmission((uint8_t)_gpsI2Caddress); //There is no register to write to, we just begin writing data bytes
  _i2cPort->write(0xFF);
  if (_i2cPort->endTransmission() != 0)         //Don't release bus
    return (SFE_UBLOX_STATUS_I2C_COMM_FAILURE); //Sensor did not ACK

  //Write header bytes
  _i2cPort->beginTransmission((uint8_t)_gpsI2Caddress); //There is no register to write to, we just begin writing data bytes
  _i2cPort->write(UBX_SYNCH_1);                         //μ - oh ublox, you're funny. I will call you micro-blox from now on.
  _i2cPort->write(UBX_SYNCH_2);                         //b
  _i2cPort->write(outgoingUBX.cls);
  _i2cPort->write(outgoingUBX.id);
  _i2cPort->write(outgoingUBX.len & 0xFF);      //LSB
  _i2cPort->write(outgoingUBX.len >> 8);        //MSB
  if (_i2cPort->endTransmission(false) != 0)    //Do not release bus
    return (SFE_UBLOX_STATUS_I2C_COMM_FAILURE); //Sensor did not ACK

  //Write payload. Limit the sends into 32 byte chunks
  //This code based on ublox: https://forum.u-blox.com/index.php/20528/how-to-use-i2c-to-get-the-nmea-frames
  uint16_t bytesToSend = outgoingUBX.len;

  //"The number of data bytes must be at least 2 to properly distinguish
  //from the write access to set the address counter in random read accesses."
  uint16_t startSpot = 0;
  while (bytesToSend > 1)
  {
    uint8_t len = bytesToSend;
    if (len > I2C_BUFFER_LENGTH)
      len = I2C_BUFFER_LENGTH;

    _i2cPort->beginTransmission((uint8_t)_gpsI2Caddress);
    //_i2cPort->write(outgoingUBX.payload, len); //Write a portion of the payload to the bus

    for (uint16_t x = 0; x < len; x++)
      _i2cPort->write(outgoingUBX.payload[startSpot + x]); //Write a portion of the payload to the bus

    if (_i2cPort->endTransmission(false) != 0)    //Don't release bus
      return (SFE_UBLOX_STATUS_I2C_COMM_FAILURE); //Sensor did not ACK

    //*outgoingUBX.payload += len; //Move the pointer forward
    startSpot += len; //Move the pointer forward
    bytesToSend -= len;
  }

  //Write checksum
  _i2cPort->beginTransmission((uint8_t)_gpsI2Caddress);
  if (bytesToSend == 1)
    _i2cPort->write(outgoingUBX.payload, 1);
  _i2cPort->write(outgoingUBX.checksumA);
  _i2cPort->write(outgoingUBX.checksumB);

  //All done transmitting bytes. Release bus.
  if (_i2cPort->endTransmission() != 0)
    return (SFE_UBLOX_STATUS_I2C_COMM_FAILURE); //Sensor did not ACK
  return (SFE_UBLOX_STATUS_SUCCESS);
}

//Given a packet and payload, send everything including CRC bytesA via Serial port
void SFE_UBLOX_GPS::sendSerialCommand(ubxPacket outgoingUBX)
{
  //Write header bytes
  _serialPort->write(UBX_SYNCH_1); //μ - oh ublox, you're funny. I will call you micro-blox from now on.
  _serialPort->write(UBX_SYNCH_2); //b
  _serialPort->write(outgoingUBX.cls);
  _serialPort->write(outgoingUBX.id);
  _serialPort->write(outgoingUBX.len & 0xFF); //LSB
  _serialPort->write(outgoingUBX.len >> 8);   //MSB

  //Write payload.
  for (int i = 0; i < outgoingUBX.len; i++)
  {
    _serialPort->write(outgoingUBX.payload[i]);
  }

  //Write checksum
  _serialPort->write(outgoingUBX.checksumA);
  _serialPort->write(outgoingUBX.checksumB);
}

//Returns true if I2C device ack's
boolean SFE_UBLOX_GPS::isConnected(uint16_t maxWait)
{
  if (commType == COMM_TYPE_I2C)
  {
    _i2cPort->beginTransmission((uint8_t)_gpsI2Caddress);
    return _i2cPort->endTransmission() == 0;
  }
  else if (commType == COMM_TYPE_SERIAL)
  {
    // Query navigation rate to see whether we get a meaningful response
    packetCfg.cls = UBX_CLASS_CFG;
    packetCfg.id = UBX_CFG_RATE;
    packetCfg.len = 0;
    packetCfg.startingSpot = 0;

    return (sendCommand(packetCfg, maxWait) == SFE_UBLOX_STATUS_DATA_RECEIVED); // We are polling the RATE so we expect data and an ACK
  }
  return false;
}

//Given a message, calc and store the two byte "8-Bit Fletcher" checksum over the entirety of the message
//This is called before we send a command message
void SFE_UBLOX_GPS::calcChecksum(ubxPacket *msg)
{
  msg->checksumA = 0;
  msg->checksumB = 0;

  msg->checksumA += msg->cls;
  msg->checksumB += msg->checksumA;

  msg->checksumA += msg->id;
  msg->checksumB += msg->checksumA;

  msg->checksumA += (msg->len & 0xFF);
  msg->checksumB += msg->checksumA;

  msg->checksumA += (msg->len >> 8);
  msg->checksumB += msg->checksumA;

  for (uint16_t i = 0; i < msg->len; i++)
  {
    msg->checksumA += msg->payload[i];
    msg->checksumB += msg->checksumA;
  }
}

//Given a message and a byte, add to rolling "8-Bit Fletcher" checksum
//This is used when receiving messages from module
void SFE_UBLOX_GPS::addToChecksum(uint8_t incoming)
{
  rollingChecksumA += incoming;
  rollingChecksumB += rollingChecksumA;
}

//Pretty prints the current ubxPacket
void SFE_UBLOX_GPS::printPacket(ubxPacket *packet)
{
  if (_printDebug == true)
  {
    _debugSerial->print(F("CLS:"));
    if (packet->cls == UBX_CLASS_NAV) //1
      _debugSerial->print("NAV");
    else if (packet->cls == UBX_CLASS_ACK) //5
      _debugSerial->print("ACK");
    else if (packet->cls == UBX_CLASS_CFG) //6
      _debugSerial->print("CFG");
    else if (packet->cls == UBX_CLASS_MON) //0x0A
      _debugSerial->print("MON");
    else
      _debugSerial->print(packet->cls, HEX);

    _debugSerial->print(F(" ID:"));
    if (packet->cls == UBX_CLASS_NAV && packet->id == UBX_NAV_PVT)
      _debugSerial->print("PVT");
    else if (packet->cls == UBX_CLASS_CFG && packet->id == UBX_CFG_RATE)
      _debugSerial->print("RATE");
    else if (packet->cls == UBX_CLASS_CFG && packet->id == UBX_CFG_CFG)
      _debugSerial->print("SAVE");
    else
      _debugSerial->print(packet->id, HEX);

    _debugSerial->print(F(" Len: 0x"));
    _debugSerial->print(packet->len, HEX);

    _debugSerial->print(F(" Payload:"));

    for (int x = 0; x < packet->len; x++)
    {
      _debugSerial->print(F(" "));
      _debugSerial->print(packet->payload[x], HEX);
    }
    _debugSerial->println();
  }
}

//=-=-=-=-=-=-=-= Specific commands =-=-=-=-=-=-=-==-=-=-=-=-=-=-=
//=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-==-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=

//When messages from the class CFG are sent to the receiver, the receiver will send an "acknowledge"(UBX - ACK - ACK) or a
//"not acknowledge"(UBX-ACK-NAK) message back to the sender, depending on whether or not the message was processed correctly.
//Some messages from other classes also use the same acknowledgement mechanism.

//When we poll or get a setting, we will receive _both_ a config packet and an ACK
//If the poll or get request is not valid, we will receive _only_ a NACK

//If we are trying to get or poll a setting, then packetCfg.len will be 0 or 1 when the packetCfg is _sent_.
//If we poll the setting for a particular port using UBX-CFG-PRT then .len will be 1 initially
//For all other gets or polls, .len will be 0 initially
//(It would be possible for .len to be 2 _if_ we were using UBX-CFG-MSG to poll the settings for a particular message - but we don't use that (currently))

//If the get or poll _fails_, i.e. is NACK'd, then packetCfg.len could still be 0 or 1 after the NACK is received
//But if the get or poll is ACK'd, then packetCfg.len will have been updated by the incoming data and will always be at least 2

//If we are going to set the value for a setting, then packetCfg.len will be at least 3 when the packetCfg is _sent_.
//(UBX-CFG-MSG appears to have the shortest set length of 3 bytes)

//Returns SFE_UBLOX_STATUS_DATA_RECEIVED if we got an ACK and a valid packetCfg (module is responding with register content)
//Returns SFE_UBLOX_STATUS_DATA_SENT if we got an ACK and no packetCfg (no valid packetCfg needed, module absorbs new register data)
//Returns SFE_UBLOX_STATUS_FAIL if we got an invalid packetCfg (checksum failure)
//Returns SFE_UBLOX_STATUS_COMMAND_UNKNOWN if we got a NACK (command unknown)
//Returns SFE_UBLOX_STATUS_TIMEOUT if we timed out
sfe_ublox_status_e SFE_UBLOX_GPS::waitForACKResponse(uint8_t requestedClass, uint8_t requestedID, uint16_t maxTime)
{
  commandAck = UBX_ACK_NONE; //Reset flag
  packetCfg.valid = SFE_UBLOX_PACKET_VALIDITY_NOT_DEFINED;   //This will go VALID (or NOT_VALID) when we receive a response to the packet we sent
  packetAck.valid = SFE_UBLOX_PACKET_VALIDITY_NOT_DEFINED;

  unsigned long startTime = millis();
  while (millis() - startTime < maxTime)
  {
    if (checkUblox() == true) //See if new data is available. Process bytes as they come in.
    {
      //First we verify the ACK. commandAck will only go UBX_ACK_ACK if CLS/ID matches
      if (commandAck == UBX_ACK_ACK)
      {
        if (_printDebug == true)
        {
          _debugSerial->print(F("waitForACKResponse: ACK received after "));
          _debugSerial->print(millis() - startTime);
          _debugSerial->println(F(" msec"));
        }

        //We've got the a valid ACK for this CLS/ID, so is packetCfg valid?
        if (packetCfg.valid == SFE_UBLOX_PACKET_VALIDITY_VALID)
        {
          //We've got a valid packetCfg, so does it match the requested Class and ID?
          if (packetCfg.cls == requestedClass && packetCfg.id == requestedID)
          {
            if (_printDebug == true)
            {
              _debugSerial->print(F("waitForACKResponse: CLS/ID match after "));
              _debugSerial->print(millis() - startTime);
              _debugSerial->println(F(" msec"));
            }
            return (SFE_UBLOX_STATUS_DATA_RECEIVED); //Received a data and a correct ACK!
          }
          else
          // The Class and/or ID don't match the requested ones, so keep trying...
          {
            //Reset packet and continue checking incoming data for matching cls/id
            if (_printDebug == true)
            {
              _debugSerial->println(F("waitForACKResponse: CLS/ID mismatch, continue to wait..."));
            }
            packetCfg.valid = SFE_UBLOX_PACKET_VALIDITY_NOT_DEFINED; //This will go VALID (or NOT_VALID) when we receive a response to the packet we sent
          }
        }
        //If we received an invalid packetCfg (checksum failure) then we can't trust it, including its Class and ID
        else if (packetCfg.valid == SFE_UBLOX_PACKET_VALIDITY_NOT_VALID)
        {
          //We were expecting data but didn't get a valid config packet
          if (_printDebug == true)
          {
            _debugSerial->println(F("waitForACKResponse: Invalid config packet"));
          }
          return (SFE_UBLOX_STATUS_FAIL); //We got a checksum failure, we're never going to get valid config data
        }
        //We didn't receive a valid or invalid packetCfg, so we must have only received the ACK
        //Let's hope this was a set?
        else
        {
          //We have sent new data. We expect an ACK but no return config packet.
          if (_printDebug == true)
          {
            _debugSerial->println(F("waitForACKResponse: New data successfully sent"));
          }
          return (SFE_UBLOX_STATUS_DATA_SENT); //New data successfully sent
        }
      }
      //Did we receive a NACK?
      else if (commandAck == UBX_ACK_NACK)
      {
        if (_printDebug == true)
        {
          _debugSerial->print(F("waitForACKResponse: NACK received after "));
          _debugSerial->print(millis() - startTime);
          _debugSerial->println(F(" msec"));
        }
        return (SFE_UBLOX_STATUS_COMMAND_UNKNOWN); //Received a NACK
      }
    } //checkUblox == true

    delayMicroseconds(500);
  } //while (millis() - startTime < maxTime)

  //TODO add check here if config went valid but we never got the following ack
  //Through debug warning, This command might not get an ACK
  if (packetCfg.valid == SFE_UBLOX_PACKET_VALIDITY_VALID)
  {
    if (_printDebug == true)
    {
      _debugSerial->println(F("waitForACKResponse: Config was valid but ACK not received"));
    }
  }

  if (_printDebug == true)
  {
    _debugSerial->print(F("waitForACKResponse: timeout after "));
    _debugSerial->print(millis() - startTime);
    _debugSerial->println(F(" msec. No ack packet received."));
  }

  return (SFE_UBLOX_STATUS_TIMEOUT);
}

//For non-CFG queries no ACK is sent so we use this function
//Returns SFE_UBLOX_STATUS_DATA_RECEIVED if we got a config packet full of response data that has CLS/ID match to our query packet
//Returns SFE_UBLOX_STATUS_CRC_FAIL if we got a corrupt config packet that has CLS/ID match to our query packet
//Returns SFE_UBLOX_STATUS_TIMEOUT if we timed out
sfe_ublox_status_e SFE_UBLOX_GPS::waitForNoACKResponse(uint8_t requestedClass, uint8_t requestedID, uint16_t maxTime)
{
  packetCfg.valid = SFE_UBLOX_PACKET_VALIDITY_NOT_DEFINED; //This will go VALID (or NOT_VALID) when we receive a response to the packet we sent
  packetAck.valid = SFE_UBLOX_PACKET_VALIDITY_NOT_DEFINED;
  packetCfg.cls = 255;
  packetCfg.id = 255;

  unsigned long startTime = millis();
  while (millis() - startTime < maxTime)
  {
    if (checkUblox() == true) //See if new data is available. Process bytes as they come in.
    {
      //Did we receive a config packet that matches the cls/id we requested?
      if ((packetCfg.cls == requestedClass) && (packetCfg.id == requestedID) && (packetCfg.valid != SFE_UBLOX_PACKET_VALIDITY_NOT_DEFINED))
      {
        //This packet might be good or it might be CRC corrupt
        if (packetCfg.valid == SFE_UBLOX_PACKET_VALIDITY_VALID)
        {
          if (_printDebug == true)
          {
            _debugSerial->print(F("waitForNoACKResponse: CLS/ID match after "));
            _debugSerial->print(millis() - startTime);
            _debugSerial->println(F(" msec"));
          }
          return (SFE_UBLOX_STATUS_DATA_RECEIVED); //We have new data to act upon
        }
        else // if (packetCfg.valid == SFE_UBLOX_PACKET_VALIDITY_NOT_VALID)
        {
          if (_printDebug == true)
          {
            _debugSerial->println(F("waitForNoACKResponse: CLS/ID match but failed CRC"));
          }
          return (SFE_UBLOX_STATUS_CRC_FAIL); //We got the right packet but it was corrupt
        }
      }
      else if ((packetCfg.cls < 255) && (packetCfg.id < 255) && (packetCfg.valid != SFE_UBLOX_PACKET_VALIDITY_NOT_DEFINED))
      {
        //We got a valid or invalid packet but it was not the droid we were looking for
        //Reset packet and continue checking incoming data for matching cls/id
        if (_printDebug == true)
        {
          _debugSerial->print(F("waitForNoACKResponse: CLS/ID mismatch: "));
          _debugSerial->print(F("CLS: "));
          _debugSerial->print(packetCfg.cls, HEX);
          _debugSerial->print(F(" ID: "));
          _debugSerial->print(packetCfg.id, HEX);
          _debugSerial->println();
        }

        packetCfg.valid = SFE_UBLOX_PACKET_VALIDITY_NOT_DEFINED; //This will go VALID (or NOT_VALID) when we receive a response to the packet we sent
        packetCfg.cls = 255;
        packetCfg.id = 255;
      }
    }

    delayMicroseconds(500);
  }

  if (_printDebug == true)
  {
    _debugSerial->print(F("waitForNoACKResponse: timeout after "));
    _debugSerial->print(millis() - startTime);
    _debugSerial->println(F(" msec. No packet received."));
  }

  return (SFE_UBLOX_STATUS_TIMEOUT);
}

//Save current configuration to flash and BBR (battery backed RAM)
//This still works but it is the old way of configuring ublox modules. See getVal and setVal for the new methods
boolean SFE_UBLOX_GPS::saveConfiguration(uint16_t maxWait)
{
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_CFG;
  packetCfg.len = 12;
  packetCfg.startingSpot = 0;

  //Clear packet payload
  for (uint8_t x = 0; x < packetCfg.len; x++)
    packetCfg.payload[x] = 0;

  packetCfg.payload[4] = 0xFF; //Set any bit in the saveMask field to save current config to Flash and BBR
  packetCfg.payload[5] = 0xFF;

  return (sendCommand(packetCfg, maxWait) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Save the selected configuration sub-sections to flash and BBR (battery backed RAM)
//This still works but it is the old way of configuring ublox modules. See getVal and setVal for the new methods
boolean SFE_UBLOX_GPS::saveConfigSelective(uint32_t configMask, uint16_t maxWait)
{
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_CFG;
  packetCfg.len = 12;
  packetCfg.startingSpot = 0;

  //Clear packet payload
  for (uint8_t x = 0; x < packetCfg.len; x++)
    packetCfg.payload[x] = 0;

  packetCfg.payload[4] = configMask & 0xFF; //Set the appropriate bits in the saveMask field to save current config to Flash and BBR
  packetCfg.payload[5] = (configMask >> 8) & 0xFF;
  packetCfg.payload[6] = (configMask >> 16) & 0xFF;
  packetCfg.payload[7] = (configMask >> 24) & 0xFF;

  return (sendCommand(packetCfg, maxWait) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Reset module to factory defaults
//This still works but it is the old way of configuring ublox modules. See getVal and setVal for the new methods
boolean SFE_UBLOX_GPS::factoryDefault(uint16_t maxWait)
{
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_CFG;
  packetCfg.len = 12;
  packetCfg.startingSpot = 0;

  //Clear packet payload
  for (uint8_t x = 0; x < packetCfg.len; x++)
    packetCfg.payload[x] = 0;

  packetCfg.payload[0] = 0xFF; //Set any bit in the clearMask field to clear saved config
  packetCfg.payload[1] = 0xFF;
  packetCfg.payload[8] = 0xFF; //Set any bit in the loadMask field to discard current config and rebuild from lower non-volatile memory layers
  packetCfg.payload[9] = 0xFF;

  return (sendCommand(packetCfg, maxWait) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Given a group, ID and size, return the value of this config spot
//The 32-bit key is put together from group/ID/size. See other getVal to send key directly.
//Configuration of modern Ublox modules is now done via getVal/setVal/delVal, ie protocol v27 and above found on ZED-F9P
uint8_t SFE_UBLOX_GPS::getVal8(uint16_t group, uint16_t id, uint8_t size, uint8_t layer, uint16_t maxWait)
{
  //Create key
  uint32_t key = 0;
  key |= (uint32_t)id;
  key |= (uint32_t)group << 16;
  key |= (uint32_t)size << 28;

  if (_printDebug == true)
  {
    _debugSerial->print(F("key: 0x"));
    _debugSerial->print(key, HEX);
    _debugSerial->println();
  }

  return getVal8(key, layer, maxWait);
}

//Given a key, return its value
//This function takes a full 32-bit key
//Default layer is BBR
//Configuration of modern Ublox modules is now done via getVal/setVal/delVal, ie protocol v27 and above found on ZED-F9P
uint8_t SFE_UBLOX_GPS::getVal8(uint32_t key, uint8_t layer, uint16_t maxWait)
{
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_VALGET;
  packetCfg.len = 4 + 4 * 1; //While multiple keys are allowed, we will send only one key at a time
  packetCfg.startingSpot = 0;

  //Clear packet payload
  for (uint8_t x = 0; x < packetCfg.len; x++)
    packetCfg.payload[x] = 0;

  //VALGET uses different memory layer definitions to VALSET
  //because it can only return the value for one layer.
  //So we need to fiddle the layer here.
  //And just to complicate things further, the ZED-F9P only responds
  //correctly to layer 0 (RAM) and layer 7 (Default)!
  uint8_t getLayer = 7; // 7 is the "Default Layer"
  if ((layer & VAL_LAYER_RAM) == VAL_LAYER_RAM) // Did the user request the RAM layer?
  {
    getLayer = 0; // Layer 0 is RAM
  }

  payloadCfg[0] = 0;     //Message Version - set to 0
  payloadCfg[1] = getLayer; //Layer

  //Load key into outgoing payload
  payloadCfg[4] = key >> 8 * 0; //Key LSB
  payloadCfg[5] = key >> 8 * 1;
  payloadCfg[6] = key >> 8 * 2;
  payloadCfg[7] = key >> 8 * 3;

  if (_printDebug == true)
  {
    _debugSerial->print(F("key: 0x"));
    _debugSerial->print(key, HEX);
    _debugSerial->println();
  }

  //Send VALGET command with this key

  sfe_ublox_status_e retVal = sendCommand(packetCfg, maxWait);
  if (_printDebug == true)
  {
    _debugSerial->print(F("getVal8: sendCommand returned: "));
    _debugSerial->println(statusString(retVal));
  }
  if (retVal != SFE_UBLOX_STATUS_DATA_RECEIVED) // We are expecting data and an ACK
    return (0); //If command send fails then bail

  //Verify the response is the correct length as compared to what the user called (did the module respond with 8-bits but the user called getVal32?)
  //Response is 8 bytes plus cfg data
  //if(packet->len > 8+1)

  //Pull the requested value from the response
  //Response starts at 4+1*N with the 32-bit key so the actual data we're looking for is at 8+1*N
  return (extractByte(8));
}

//Given a key, set a 16-bit value
//This function takes a full 32-bit key
//Default layer is BBR
//Configuration of modern Ublox modules is now done via getVal/setVal/delVal, ie protocol v27 and above found on ZED-F9P
uint8_t SFE_UBLOX_GPS::setVal(uint32_t key, uint16_t value, uint8_t layer, uint16_t maxWait)
{
  return setVal16(key, value, layer, maxWait);
}

//Given a key, set a 16-bit value
//This function takes a full 32-bit key
//Default layer is BBR
//Configuration of modern Ublox modules is now done via getVal/setVal/delVal, ie protocol v27 and above found on ZED-F9P
uint8_t SFE_UBLOX_GPS::setVal16(uint32_t key, uint16_t value, uint8_t layer, uint16_t maxWait)
{
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_VALSET;
  packetCfg.len = 4 + 4 + 2; //4 byte header, 4 byte key ID, 2 bytes of value
  packetCfg.startingSpot = 0;

  //Clear packet payload
  for (uint16_t x = 0; x < packetCfg.len; x++)
    packetCfg.payload[x] = 0;

  payloadCfg[0] = 0;     //Message Version - set to 0
  payloadCfg[1] = layer; //By default we ask for the BBR layer

  //Load key into outgoing payload
  payloadCfg[4] = key >> 8 * 0; //Key LSB
  payloadCfg[5] = key >> 8 * 1;
  payloadCfg[6] = key >> 8 * 2;
  payloadCfg[7] = key >> 8 * 3;

  //Load user's value
  payloadCfg[8] = value >> 8 * 0; //Value LSB
  payloadCfg[9] = value >> 8 * 1;

  //Send VALSET command with this key and value
  return (sendCommand(packetCfg, maxWait) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Given a key, set an 8-bit value
//This function takes a full 32-bit key
//Default layer is BBR
//Configuration of modern Ublox modules is now done via getVal/setVal/delVal, ie protocol v27 and above found on ZED-F9P
uint8_t SFE_UBLOX_GPS::setVal8(uint32_t key, uint8_t value, uint8_t layer, uint16_t maxWait)
{
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_VALSET;
  packetCfg.len = 4 + 4 + 1; //4 byte header, 4 byte key ID, 1 byte value
  packetCfg.startingSpot = 0;

  //Clear packet payload
  for (uint16_t x = 0; x < packetCfg.len; x++)
    packetCfg.payload[x] = 0;

  payloadCfg[0] = 0;     //Message Version - set to 0
  payloadCfg[1] = layer; //By default we ask for the BBR layer

  //Load key into outgoing payload
  payloadCfg[4] = key >> 8 * 0; //Key LSB
  payloadCfg[5] = key >> 8 * 1;
  payloadCfg[6] = key >> 8 * 2;
  payloadCfg[7] = key >> 8 * 3;

  //Load user's value
  payloadCfg[8] = value; //Value

  //Send VALSET command with this key and value
  return (sendCommand(packetCfg, maxWait) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Given a key, set a 32-bit value
//This function takes a full 32-bit key
//Default layer is BBR
//Configuration of modern Ublox modules is now done via getVal/setVal/delVal, ie protocol v27 and above found on ZED-F9P
uint8_t SFE_UBLOX_GPS::setVal32(uint32_t key, uint32_t value, uint8_t layer, uint16_t maxWait)
{
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_VALSET;
  packetCfg.len = 4 + 4 + 4; //4 byte header, 4 byte key ID, 4 bytes of value
  packetCfg.startingSpot = 0;

  //Clear packet payload
  for (uint16_t x = 0; x < packetCfg.len; x++)
    packetCfg.payload[x] = 0;

  payloadCfg[0] = 0;     //Message Version - set to 0
  payloadCfg[1] = layer; //By default we ask for the BBR layer

  //Load key into outgoing payload
  payloadCfg[4] = key >> 8 * 0; //Key LSB
  payloadCfg[5] = key >> 8 * 1;
  payloadCfg[6] = key >> 8 * 2;
  payloadCfg[7] = key >> 8 * 3;

  //Load user's value
  payloadCfg[8] = value >> 8 * 0; //Value LSB
  payloadCfg[9] = value >> 8 * 1;
  payloadCfg[10] = value >> 8 * 2;
  payloadCfg[11] = value >> 8 * 3;

  //Send VALSET command with this key and value
  return (sendCommand(packetCfg, maxWait) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Start defining a new UBX-CFG-VALSET ubxPacket
//This function takes a full 32-bit key and 32-bit value
//Default layer is BBR
//Configuration of modern Ublox modules is now done via getVal/setVal/delVal, ie protocol v27 and above found on ZED-F9P
uint8_t SFE_UBLOX_GPS::newCfgValset32(uint32_t key, uint32_t value, uint8_t layer)
{
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_VALSET;
  packetCfg.len = 4 + 4 + 4; //4 byte header, 4 byte key ID, 4 bytes of value
  packetCfg.startingSpot = 0;

  //Clear packet payload
  for (uint16_t x = 0; x < MAX_PAYLOAD_SIZE; x++)
    packetCfg.payload[x] = 0;

  payloadCfg[0] = 0;     //Message Version - set to 0
  payloadCfg[1] = layer; //By default we ask for the BBR layer

  //Load key into outgoing payload
  payloadCfg[4] = key >> 8 * 0; //Key LSB
  payloadCfg[5] = key >> 8 * 1;
  payloadCfg[6] = key >> 8 * 2;
  payloadCfg[7] = key >> 8 * 3;

  //Load user's value
  payloadCfg[8] = value >> 8 * 0; //Value LSB
  payloadCfg[9] = value >> 8 * 1;
  payloadCfg[10] = value >> 8 * 2;
  payloadCfg[11] = value >> 8 * 3;

  //All done
  return (true);
}

//Start defining a new UBX-CFG-VALSET ubxPacket
//This function takes a full 32-bit key and 16-bit value
//Default layer is BBR
//Configuration of modern Ublox modules is now done via getVal/setVal/delVal, ie protocol v27 and above found on ZED-F9P
uint8_t SFE_UBLOX_GPS::newCfgValset16(uint32_t key, uint16_t value, uint8_t layer)
{
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_VALSET;
  packetCfg.len = 4 + 4 + 2; //4 byte header, 4 byte key ID, 2 bytes of value
  packetCfg.startingSpot = 0;

  //Clear packet payload
  for (uint16_t x = 0; x < MAX_PAYLOAD_SIZE; x++)
    packetCfg.payload[x] = 0;

  payloadCfg[0] = 0;     //Message Version - set to 0
  payloadCfg[1] = layer; //By default we ask for the BBR layer

  //Load key into outgoing payload
  payloadCfg[4] = key >> 8 * 0; //Key LSB
  payloadCfg[5] = key >> 8 * 1;
  payloadCfg[6] = key >> 8 * 2;
  payloadCfg[7] = key >> 8 * 3;

  //Load user's value
  payloadCfg[8] = value >> 8 * 0; //Value LSB
  payloadCfg[9] = value >> 8 * 1;

  //All done
  return (true);
}

//Start defining a new UBX-CFG-VALSET ubxPacket
//This function takes a full 32-bit key and 8-bit value
//Default layer is BBR
//Configuration of modern Ublox modules is now done via getVal/setVal/delVal, ie protocol v27 and above found on ZED-F9P
uint8_t SFE_UBLOX_GPS::newCfgValset8(uint32_t key, uint8_t value, uint8_t layer)
{
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_VALSET;
  packetCfg.len = 4 + 4 + 1; //4 byte header, 4 byte key ID, 1 byte value
  packetCfg.startingSpot = 0;

  //Clear packet payload
  for (uint16_t x = 0; x < MAX_PAYLOAD_SIZE; x++)
    packetCfg.payload[x] = 0;

  payloadCfg[0] = 0;     //Message Version - set to 0
  payloadCfg[1] = layer; //By default we ask for the BBR layer

  //Load key into outgoing payload
  payloadCfg[4] = key >> 8 * 0; //Key LSB
  payloadCfg[5] = key >> 8 * 1;
  payloadCfg[6] = key >> 8 * 2;
  payloadCfg[7] = key >> 8 * 3;

  //Load user's value
  payloadCfg[8] = value; //Value

  //All done
  return (true);
}

//Add another keyID and value to an existing UBX-CFG-VALSET ubxPacket
//This function takes a full 32-bit key and 32-bit value
uint8_t SFE_UBLOX_GPS::addCfgValset32(uint32_t key, uint32_t value)
{
  //Load key into outgoing payload
  payloadCfg[packetCfg.len + 0] = key >> 8 * 0; //Key LSB
  payloadCfg[packetCfg.len + 1] = key >> 8 * 1;
  payloadCfg[packetCfg.len + 2] = key >> 8 * 2;
  payloadCfg[packetCfg.len + 3] = key >> 8 * 3;

  //Load user's value
  payloadCfg[packetCfg.len + 4] = value >> 8 * 0; //Value LSB
  payloadCfg[packetCfg.len + 5] = value >> 8 * 1;
  payloadCfg[packetCfg.len + 6] = value >> 8 * 2;
  payloadCfg[packetCfg.len + 7] = value >> 8 * 3;

  //Update packet length: 4 byte key ID, 4 bytes of value
  packetCfg.len = packetCfg.len + 4 + 4;

  //All done
  return (true);
}

//Add another keyID and value to an existing UBX-CFG-VALSET ubxPacket
//This function takes a full 32-bit key and 16-bit value
uint8_t SFE_UBLOX_GPS::addCfgValset16(uint32_t key, uint16_t value)
{
  //Load key into outgoing payload
  payloadCfg[packetCfg.len + 0] = key >> 8 * 0; //Key LSB
  payloadCfg[packetCfg.len + 1] = key >> 8 * 1;
  payloadCfg[packetCfg.len + 2] = key >> 8 * 2;
  payloadCfg[packetCfg.len + 3] = key >> 8 * 3;

  //Load user's value
  payloadCfg[packetCfg.len + 4] = value >> 8 * 0; //Value LSB
  payloadCfg[packetCfg.len + 5] = value >> 8 * 1;

  //Update packet length: 4 byte key ID, 2 bytes of value
  packetCfg.len = packetCfg.len + 4 + 2;

  //All done
  return (true);
}

//Add another keyID and value to an existing UBX-CFG-VALSET ubxPacket
//This function takes a full 32-bit key and 8-bit value
uint8_t SFE_UBLOX_GPS::addCfgValset8(uint32_t key, uint8_t value)
{
  //Load key into outgoing payload
  payloadCfg[packetCfg.len + 0] = key >> 8 * 0; //Key LSB
  payloadCfg[packetCfg.len + 1] = key >> 8 * 1;
  payloadCfg[packetCfg.len + 2] = key >> 8 * 2;
  payloadCfg[packetCfg.len + 3] = key >> 8 * 3;

  //Load user's value
  payloadCfg[packetCfg.len + 4] = value; //Value

  //Update packet length: 4 byte key ID, 1 byte value
  packetCfg.len = packetCfg.len + 4 + 1;

  //All done
  return (true);
}

//Add a final keyID and value to an existing UBX-CFG-VALSET ubxPacket and send it
//This function takes a full 32-bit key and 32-bit value
uint8_t SFE_UBLOX_GPS::sendCfgValset32(uint32_t key, uint32_t value, uint16_t maxWait)
{
  //Load keyID and value into outgoing payload
  addCfgValset32(key, value);

  //Send VALSET command with this key and value
  return (sendCommand(packetCfg, maxWait) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Add a final keyID and value to an existing UBX-CFG-VALSET ubxPacket and send it
//This function takes a full 32-bit key and 16-bit value
uint8_t SFE_UBLOX_GPS::sendCfgValset16(uint32_t key, uint16_t value, uint16_t maxWait)
{
  //Load keyID and value into outgoing payload
  addCfgValset16(key, value);

  //Send VALSET command with this key and value
  return (sendCommand(packetCfg, maxWait) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Add a final keyID and value to an existing UBX-CFG-VALSET ubxPacket and send it
//This function takes a full 32-bit key and 8-bit value
uint8_t SFE_UBLOX_GPS::sendCfgValset8(uint32_t key, uint8_t value, uint16_t maxWait)
{
  //Load keyID and value into outgoing payload
  addCfgValset8(key, value);

  //Send VALSET command with this key and value
  return (sendCommand(packetCfg, maxWait) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Get the current TimeMode3 settings - these contain survey in statuses
boolean SFE_UBLOX_GPS::getSurveyMode(uint16_t maxWait)
{
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_TMODE3;
  packetCfg.len = 0;
  packetCfg.startingSpot = 0;

  return ((sendCommand(packetCfg, maxWait)) == SFE_UBLOX_STATUS_DATA_RECEIVED); // We are expecting data and an ACK
}

//Control Survey-In for NEO-M8P
boolean SFE_UBLOX_GPS::setSurveyMode(uint8_t mode, uint16_t observationTime, float requiredAccuracy, uint16_t maxWait)
{
  if (getSurveyMode(maxWait) == false) //Ask module for the current TimeMode3 settings. Loads into payloadCfg.
    return (false);

  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_TMODE3;
  packetCfg.len = 40;
  packetCfg.startingSpot = 0;

  //Clear packet payload
  for (uint8_t x = 0; x < packetCfg.len; x++)
    packetCfg.payload[x] = 0;

  //payloadCfg should be loaded with poll response. Now modify only the bits we care about
  payloadCfg[2] = mode; //Set mode. Survey-In and Disabled are most common.

  payloadCfg[24] = observationTime & 0xFF; //svinMinDur in seconds
  payloadCfg[25] = observationTime >> 8;   //svinMinDur in seconds

  uint32_t svinAccLimit = requiredAccuracy * 10000; //Convert m to 0.1mm
  payloadCfg[28] = svinAccLimit & 0xFF;             //svinAccLimit in 0.1mm increments
  payloadCfg[29] = svinAccLimit >> 8;
  payloadCfg[30] = svinAccLimit >> 16;

  return ((sendCommand(packetCfg, maxWait)) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Begin Survey-In for NEO-M8P
boolean SFE_UBLOX_GPS::enableSurveyMode(uint16_t observationTime, float requiredAccuracy, uint16_t maxWait)
{
  return (setSurveyMode(SVIN_MODE_ENABLE, observationTime, requiredAccuracy, maxWait));
}

//Stop Survey-In for NEO-M8P
boolean SFE_UBLOX_GPS::disableSurveyMode(uint16_t maxWait)
{
  return (setSurveyMode(SVIN_MODE_DISABLE, 0, 0, maxWait));
}

//Reads survey in status and sets the global variables
//for status, position valid, observation time, and mean 3D StdDev
//Returns true if commands was successful
boolean SFE_UBLOX_GPS::getSurveyStatus(uint16_t maxWait)
{
  //Reset variables
  svin.active = false;
  svin.valid = false;
  svin.observationTime = 0;
  svin.meanAccuracy = 0;

  packetCfg.cls = UBX_CLASS_NAV;
  packetCfg.id = UBX_NAV_SVIN;
  packetCfg.len = 0;
  packetCfg.startingSpot = 0;

  if ((sendCommand(packetCfg, maxWait)) != SFE_UBLOX_STATUS_DATA_RECEIVED) // We are expecting data and an ACK
    return (false); //If command send fails then bail

  //We got a response, now parse the bits into the svin structure
  svin.observationTime = extractLong(8);

  uint32_t tempFloat = extractLong(28);
  svin.meanAccuracy = tempFloat / 10000.0; //Convert 0.1mm to m

  svin.valid = payloadCfg[36];
  svin.active = payloadCfg[37]; //1 if survey in progress, 0 otherwise

  return (true);
}

//Loads the payloadCfg array with the current protocol bits located the UBX-CFG-PRT register for a given port
boolean SFE_UBLOX_GPS::getPortSettings(uint8_t portID, uint16_t maxWait)
{
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_PRT;
  packetCfg.len = 1;
  packetCfg.startingSpot = 0;

  payloadCfg[0] = portID;

  return ((sendCommand(packetCfg, maxWait)) == SFE_UBLOX_STATUS_DATA_RECEIVED); // We are expecting data and an ACK
}

//Configure a given port to output UBX, NMEA, RTCM3 or a combination thereof
//Port 0=I2c, 1=UART1, 2=UART2, 3=USB, 4=SPI
//Bit:0 = UBX, :1=NMEA, :5=RTCM3
boolean SFE_UBLOX_GPS::setPortOutput(uint8_t portID, uint8_t outStreamSettings, uint16_t maxWait)
{
  //Get the current config values for this port ID
  if (getPortSettings(portID, maxWait) == false)
    return (false); //Something went wrong. Bail.

  if (commandAck != UBX_ACK_ACK)
  {
    if (_printDebug == true)
    {
      _debugSerial->println(F("setPortOutput failed to ACK"));
    }
    return (false);
  }

  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_PRT;
  packetCfg.len = 20;
  packetCfg.startingSpot = 0;

  //payloadCfg is now loaded with current bytes. Change only the ones we need to
  payloadCfg[14] = outStreamSettings; //OutProtocolMask LSB - Set outStream bits

  return ((sendCommand(packetCfg, maxWait)) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Configure a given port to input UBX, NMEA, RTCM3 or a combination thereof
//Port 0=I2c, 1=UART1, 2=UART2, 3=USB, 4=SPI
//Bit:0 = UBX, :1=NMEA, :5=RTCM3
boolean SFE_UBLOX_GPS::setPortInput(uint8_t portID, uint8_t inStreamSettings, uint16_t maxWait)
{
  //Get the current config values for this port ID
  //This will load the payloadCfg array with current port settings
  if (getPortSettings(portID, maxWait) == false)
    return (false); //Something went wrong. Bail.

  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_PRT;
  packetCfg.len = 20;
  packetCfg.startingSpot = 0;

  //payloadCfg is now loaded with current bytes. Change only the ones we need to
  payloadCfg[12] = inStreamSettings; //InProtocolMask LSB - Set inStream bits

  return ((sendCommand(packetCfg, maxWait)) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Configure a port to output UBX, NMEA, RTCM3 or a combination thereof
boolean SFE_UBLOX_GPS::setI2COutput(uint8_t comSettings, uint16_t maxWait)
{
  return (setPortOutput(COM_PORT_I2C, comSettings, maxWait));
}
boolean SFE_UBLOX_GPS::setUART1Output(uint8_t comSettings, uint16_t maxWait)
{
  return (setPortOutput(COM_PORT_UART1, comSettings, maxWait));
}
boolean SFE_UBLOX_GPS::setUART2Output(uint8_t comSettings, uint16_t maxWait)
{
  return (setPortOutput(COM_PORT_UART2, comSettings, maxWait));
}
boolean SFE_UBLOX_GPS::setUSBOutput(uint8_t comSettings, uint16_t maxWait)
{
  return (setPortOutput(COM_PORT_USB, comSettings, maxWait));
}
boolean SFE_UBLOX_GPS::setSPIOutput(uint8_t comSettings, uint16_t maxWait)
{
  return (setPortOutput(COM_PORT_SPI, comSettings, maxWait));
}

//Set the rate at which the module will give us an updated navigation solution
//Expects a number that is the updates per second. For example 1 = 1Hz, 2 = 2Hz, etc.
//Max is 40Hz(?!)
boolean SFE_UBLOX_GPS::setNavigationFrequency(uint8_t navFreq, uint16_t maxWait)
{
  //if(updateRate > 40) updateRate = 40; //Not needed: module will correct out of bounds values

  //Adjust the I2C polling timeout based on update rate
  i2cPollingWait = 1000 / (navFreq * 4); //This is the number of ms to wait between checks for new I2C data

  //Query the module for the latest lat/long
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_RATE;
  packetCfg.len = 0;
  packetCfg.startingSpot = 0;

  //This will load the payloadCfg array with current settings of the given register
  if (sendCommand(packetCfg, maxWait) != SFE_UBLOX_STATUS_DATA_RECEIVED) // We are expecting data and an ACK
    return (false); //If command send fails then bail

  uint16_t measurementRate = 1000 / navFreq;

  //payloadCfg is now loaded with current bytes. Change only the ones we need to
  payloadCfg[0] = measurementRate & 0xFF; //measRate LSB
  payloadCfg[1] = measurementRate >> 8;   //measRate MSB

  return ((sendCommand(packetCfg, maxWait)) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Get the rate at which the module is outputting nav solutions
uint8_t SFE_UBLOX_GPS::getNavigationFrequency(uint16_t maxWait)
{
  //Query the module for the latest lat/long
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_RATE;
  packetCfg.len = 0;
  packetCfg.startingSpot = 0;

  //This will load the payloadCfg array with current settings of the given register
  if (sendCommand(packetCfg, maxWait) != SFE_UBLOX_STATUS_DATA_RECEIVED) // We are expecting data and an ACK
    return (0); //If command send fails then bail

  uint16_t measurementRate = 0;

  //payloadCfg is now loaded with current bytes. Get what we need
  measurementRate = extractInt(0); //Pull from payloadCfg at measRate LSB

  measurementRate = 1000 / measurementRate; //This may return an int when it's a float, but I'd rather not return 4 bytes
  return (measurementRate);
}

//In case no config access to the GPS is possible and PVT is send cyclically already
//set config to suitable parameters
boolean SFE_UBLOX_GPS::assumeAutoPVT(boolean enabled, boolean implicitUpdate)
{
  boolean changes = autoPVT != enabled || autoPVTImplicitUpdate != implicitUpdate;
  if (changes)
  {
    autoPVT = enabled;
    autoPVTImplicitUpdate = implicitUpdate;
  }
  return changes;
}

//Enable or disable automatic navigation message generation by the GPS. This changes the way getPVT
//works.
boolean SFE_UBLOX_GPS::setAutoPVT(boolean enable, uint16_t maxWait)
{
  return setAutoPVT(enable, true, maxWait);
}

//Enable or disable automatic navigation message generation by the GPS. This changes the way getPVT
//works.
boolean SFE_UBLOX_GPS::setAutoPVT(boolean enable, boolean implicitUpdate, uint16_t maxWait)
{
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_MSG;
  packetCfg.len = 3;
  packetCfg.startingSpot = 0;
  payloadCfg[0] = UBX_CLASS_NAV;
  payloadCfg[1] = UBX_NAV_PVT;
  payloadCfg[2] = enable ? 1 : 0; // rate relative to navigation freq.

  boolean ok = ((sendCommand(packetCfg, maxWait)) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
  if (ok)
  {
    autoPVT = enable;
    autoPVTImplicitUpdate = implicitUpdate;
  }
  moduleQueried.all = false;
  return ok;
}

//Configure a given message type for a given port (UART1, I2C, SPI, etc)
boolean SFE_UBLOX_GPS::configureMessage(uint8_t msgClass, uint8_t msgID, uint8_t portID, uint8_t sendRate, uint16_t maxWait)
{
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_MSG;
  packetCfg.len = 8;
  packetCfg.startingSpot = 0;

  //Clear packet payload
  for (uint8_t x = 0; x < packetCfg.len; x++)
    packetCfg.payload[x] = 0;

  packetCfg.payload[0] = msgClass;
  packetCfg.payload[1] = msgID;
  packetCfg.payload[2 + portID] = sendRate; //Send rate is relative to the event a message is registered on. For example, if the rate of a navigation message is set to 2, the message is sent every 2nd navigation solution.

  return ((sendCommand(packetCfg, maxWait)) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Enable a given message type, default of 1 per update rate (usually 1 per second)
boolean SFE_UBLOX_GPS::enableMessage(uint8_t msgClass, uint8_t msgID, uint8_t portID, uint8_t rate, uint16_t maxWait)
{
  return (configureMessage(msgClass, msgID, portID, rate, maxWait));
}
//Disable a given message type on a given port
boolean SFE_UBLOX_GPS::disableMessage(uint8_t msgClass, uint8_t msgID, uint8_t portID, uint16_t maxWait)
{
  return (configureMessage(msgClass, msgID, portID, 0, maxWait));
}

boolean SFE_UBLOX_GPS::enableNMEAMessage(uint8_t msgID, uint8_t portID, uint8_t rate, uint16_t maxWait)
{
  return (configureMessage(UBX_CLASS_NMEA, msgID, portID, rate, maxWait));
}
boolean SFE_UBLOX_GPS::disableNMEAMessage(uint8_t msgID, uint8_t portID, uint16_t maxWait)
{
  return (enableNMEAMessage(msgID, portID, 0, maxWait));
}

//Given a message number turns on a message ID for output over a given portID (UART, I2C, SPI, USB, etc)
//To disable a message, set secondsBetween messages to 0
//Note: This function will return false if the message is already enabled
//For base station RTK output we need to enable various sentences

//NEO-M8P has four:
//1005 = 0xF5 0x05 - Stationary RTK reference ARP
//1077 = 0xF5 0x4D - GPS MSM7
//1087 = 0xF5 0x57 - GLONASS MSM7
//1230 = 0xF5 0xE6 - GLONASS code-phase biases, set to once every 10 seconds

//ZED-F9P has six:
//1005, 1074, 1084, 1094, 1124, 1230

//Much of this configuration is not documented and instead discerned from u-center binary console
boolean SFE_UBLOX_GPS::enableRTCMmessage(uint8_t messageNumber, uint8_t portID, uint8_t sendRate, uint16_t maxWait)
{
  return (configureMessage(UBX_RTCM_MSB, messageNumber, portID, sendRate, maxWait));
}

//Disable a given message on a given port by setting secondsBetweenMessages to zero
boolean SFE_UBLOX_GPS::disableRTCMmessage(uint8_t messageNumber, uint8_t portID, uint16_t maxWait)
{
  return (enableRTCMmessage(messageNumber, portID, 0, maxWait));
}

//Add a new geofence using UBX-CFG-GEOFENCE
boolean SFE_UBLOX_GPS::addGeofence(int32_t latitude, int32_t longitude, uint32_t radius, byte confidence, byte pinPolarity, byte pin, uint16_t maxWait)
{
  if (currentGeofenceParams.numFences >= 4)
    return (false); // Quit if we already have four geofences defined

  // Store the new geofence parameters
  currentGeofenceParams.lats[currentGeofenceParams.numFences] = latitude;
  currentGeofenceParams.longs[currentGeofenceParams.numFences] = longitude;
  currentGeofenceParams.rads[currentGeofenceParams.numFences] = radius;
  currentGeofenceParams.numFences = currentGeofenceParams.numFences + 1; // Increment the number of fences

  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_GEOFENCE;
  packetCfg.len = (currentGeofenceParams.numFences * 12) + 8;
  packetCfg.startingSpot = 0;

  payloadCfg[0] = 0;                               // Message version = 0x00
  payloadCfg[1] = currentGeofenceParams.numFences; // numFences
  payloadCfg[2] = confidence;                      // confLvl = Confidence level 0-4 (none, 68%, 95%, 99.7%, 99.99%)
  payloadCfg[3] = 0;                               // reserved1
  if (pin > 0)
  {
    payloadCfg[4] = 1; // enable PIO combined fence state
  }
  else
  {
    payloadCfg[4] = 0; // disable PIO combined fence state
  }
  payloadCfg[5] = pinPolarity; // PIO pin polarity (0 = low means inside, 1 = low means outside (or unknown))
  payloadCfg[6] = pin;         // PIO pin
  payloadCfg[7] = 0;           //reserved2
  payloadCfg[8] = currentGeofenceParams.lats[0] & 0xFF;
  payloadCfg[9] = currentGeofenceParams.lats[0] >> 8;
  payloadCfg[10] = currentGeofenceParams.lats[0] >> 16;
  payloadCfg[11] = currentGeofenceParams.lats[0] >> 24;
  payloadCfg[12] = currentGeofenceParams.longs[0] & 0xFF;
  payloadCfg[13] = currentGeofenceParams.longs[0] >> 8;
  payloadCfg[14] = currentGeofenceParams.longs[0] >> 16;
  payloadCfg[15] = currentGeofenceParams.longs[0] >> 24;
  payloadCfg[16] = currentGeofenceParams.rads[0] & 0xFF;
  payloadCfg[17] = currentGeofenceParams.rads[0] >> 8;
  payloadCfg[18] = currentGeofenceParams.rads[0] >> 16;
  payloadCfg[19] = currentGeofenceParams.rads[0] >> 24;
  if (currentGeofenceParams.numFences >= 2)
  {
    payloadCfg[20] = currentGeofenceParams.lats[1] & 0xFF;
    payloadCfg[21] = currentGeofenceParams.lats[1] >> 8;
    payloadCfg[22] = currentGeofenceParams.lats[1] >> 16;
    payloadCfg[23] = currentGeofenceParams.lats[1] >> 24;
    payloadCfg[24] = currentGeofenceParams.longs[1] & 0xFF;
    payloadCfg[25] = currentGeofenceParams.longs[1] >> 8;
    payloadCfg[26] = currentGeofenceParams.longs[1] >> 16;
    payloadCfg[27] = currentGeofenceParams.longs[1] >> 24;
    payloadCfg[28] = currentGeofenceParams.rads[1] & 0xFF;
    payloadCfg[29] = currentGeofenceParams.rads[1] >> 8;
    payloadCfg[30] = currentGeofenceParams.rads[1] >> 16;
    payloadCfg[31] = currentGeofenceParams.rads[1] >> 24;
  }
  if (currentGeofenceParams.numFences >= 3)
  {
    payloadCfg[32] = currentGeofenceParams.lats[2] & 0xFF;
    payloadCfg[33] = currentGeofenceParams.lats[2] >> 8;
    payloadCfg[34] = currentGeofenceParams.lats[2] >> 16;
    payloadCfg[35] = currentGeofenceParams.lats[2] >> 24;
    payloadCfg[36] = currentGeofenceParams.longs[2] & 0xFF;
    payloadCfg[37] = currentGeofenceParams.longs[2] >> 8;
    payloadCfg[38] = currentGeofenceParams.longs[2] >> 16;
    payloadCfg[39] = currentGeofenceParams.longs[2] >> 24;
    payloadCfg[40] = currentGeofenceParams.rads[2] & 0xFF;
    payloadCfg[41] = currentGeofenceParams.rads[2] >> 8;
    payloadCfg[42] = currentGeofenceParams.rads[2] >> 16;
    payloadCfg[43] = currentGeofenceParams.rads[2] >> 24;
  }
  if (currentGeofenceParams.numFences >= 4)
  {
    payloadCfg[44] = currentGeofenceParams.lats[3] & 0xFF;
    payloadCfg[45] = currentGeofenceParams.lats[3] >> 8;
    payloadCfg[46] = currentGeofenceParams.lats[3] >> 16;
    payloadCfg[47] = currentGeofenceParams.lats[3] >> 24;
    payloadCfg[48] = currentGeofenceParams.longs[3] & 0xFF;
    payloadCfg[49] = currentGeofenceParams.longs[3] >> 8;
    payloadCfg[50] = currentGeofenceParams.longs[3] >> 16;
    payloadCfg[51] = currentGeofenceParams.longs[3] >> 24;
    payloadCfg[52] = currentGeofenceParams.rads[3] & 0xFF;
    payloadCfg[53] = currentGeofenceParams.rads[3] >> 8;
    payloadCfg[54] = currentGeofenceParams.rads[3] >> 16;
    payloadCfg[55] = currentGeofenceParams.rads[3] >> 24;
  }
  return ((sendCommand(packetCfg, maxWait)) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Clear all geofences using UBX-CFG-GEOFENCE
boolean SFE_UBLOX_GPS::clearGeofences(uint16_t maxWait)
{
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_GEOFENCE;
  packetCfg.len = 8;
  packetCfg.startingSpot = 0;

  payloadCfg[0] = 0; // Message version = 0x00
  payloadCfg[1] = 0; // numFences
  payloadCfg[2] = 0; // confLvl
  payloadCfg[3] = 0; // reserved1
  payloadCfg[4] = 0; // disable PIO combined fence state
  payloadCfg[5] = 0; // PIO pin polarity (0 = low means inside, 1 = low means outside (or unknown))
  payloadCfg[6] = 0; // PIO pin
  payloadCfg[7] = 0; //reserved2

  currentGeofenceParams.numFences = 0; // Zero the number of geofences currently in use

  return ((sendCommand(packetCfg, maxWait)) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Clear the antenna control settings using UBX-CFG-ANT
//This function is hopefully redundant but may be needed to release
//any PIO pins pre-allocated for antenna functions
boolean SFE_UBLOX_GPS::clearAntPIO(uint16_t maxWait)
{
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_ANT;
  packetCfg.len = 4;
  packetCfg.startingSpot = 0;

  payloadCfg[0] = 0x10; // Antenna flag mask: set the recovery bit
  payloadCfg[1] = 0;
  payloadCfg[2] = 0xFF; // Antenna pin configuration: set pinSwitch and pinSCD to 31
  payloadCfg[3] = 0xFF; // Antenna pin configuration: set pinOCD to 31, set reconfig bit

  return ((sendCommand(packetCfg, maxWait)) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Returns the combined geofence state using UBX-NAV-GEOFENCE
boolean SFE_UBLOX_GPS::getGeofenceState(geofenceState &currentGeofenceState, uint16_t maxWait)
{
  packetCfg.cls = UBX_CLASS_NAV;
  packetCfg.id = UBX_NAV_GEOFENCE;
  packetCfg.len = 0;
  packetCfg.startingSpot = 0;

  //Ask module for the geofence status. Loads into payloadCfg.
  if (sendCommand(packetCfg, maxWait) != SFE_UBLOX_STATUS_DATA_RECEIVED) // We are expecting data and an ACK
    return (false);

  currentGeofenceState.status = payloadCfg[5];    // Extract the status
  currentGeofenceState.numFences = payloadCfg[6]; // Extract the number of geofences
  currentGeofenceState.combState = payloadCfg[7]; // Extract the combined state of all geofences
  if (currentGeofenceState.numFences > 0)
    currentGeofenceState.states[0] = payloadCfg[8]; // Extract geofence 1 state
  if (currentGeofenceState.numFences > 1)
    currentGeofenceState.states[1] = payloadCfg[10]; // Extract geofence 2 state
  if (currentGeofenceState.numFences > 2)
    currentGeofenceState.states[2] = payloadCfg[12]; // Extract geofence 3 state
  if (currentGeofenceState.numFences > 3)
    currentGeofenceState.states[3] = payloadCfg[14]; // Extract geofence 4 state

  return (true);
}

//Power Save Mode
//Enables/Disables Low Power Mode using UBX-CFG-RXM
boolean SFE_UBLOX_GPS::powerSaveMode(bool power_save, uint16_t maxWait)
{
  // Let's begin by checking the Protocol Version as UBX_CFG_RXM is not supported on the ZED (protocol >= 27)
  uint8_t protVer = getProtocolVersionHigh(maxWait);
  /*
  if (_printDebug == true)
  {
    _debugSerial->print(F("Protocol version is "));
    _debugSerial->println(protVer);
  }
  */
  if (protVer >= 27)
  {
    if (_printDebug == true)
    {
      _debugSerial->println(F("powerSaveMode (UBX-CFG-RXM) is not supported by this protocol version"));
    }
    return (false);
  }

  // Now let's change the power setting using UBX-CFG-RXM
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_RXM;
  packetCfg.len = 0;
  packetCfg.startingSpot = 0;

  //Ask module for the current power management settings. Loads into payloadCfg.
  if (sendCommand(packetCfg, maxWait) != SFE_UBLOX_STATUS_DATA_RECEIVED) // We are expecting data and an ACK
    return (false);

  if (power_save)
  {
    payloadCfg[1] = 1; // Power Save Mode
  }
  else
  {
    payloadCfg[1] = 0; // Continuous Mode
  }

  packetCfg.len = 2;
  packetCfg.startingSpot = 0;

  return (sendCommand(packetCfg, maxWait) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Change the dynamic platform model using UBX-CFG-NAV5
//Possible values are:
//PORTABLE,STATIONARY,PEDESTRIAN,AUTOMOTIVE,SEA,
//AIRBORNE1g,AIRBORNE2g,AIRBORNE4g,WRIST,BIKE
//WRIST is not supported in protocol versions less than 18
//BIKE is supported in protocol versions 19.2
boolean SFE_UBLOX_GPS::setDynamicModel(dynModel newDynamicModel, uint16_t maxWait)
{
  packetCfg.cls = UBX_CLASS_CFG;
  packetCfg.id = UBX_CFG_NAV5;
  packetCfg.len = 0;
  packetCfg.startingSpot = 0;

  //Ask module for the current navigation model settings. Loads into payloadCfg.
  if (sendCommand(packetCfg, maxWait) != SFE_UBLOX_STATUS_DATA_RECEIVED) // We are expecting data and an ACK
    return (false);

  payloadCfg[0] = 0x01;            // mask: set only the dyn bit (0)
  payloadCfg[1] = 0x00;            // mask
  payloadCfg[2] = newDynamicModel; // dynModel

  packetCfg.len = 36;
  packetCfg.startingSpot = 0;

  return (sendCommand(packetCfg, maxWait) == SFE_UBLOX_STATUS_DATA_SENT); // We are only expecting an ACK
}

//Given a spot in the payload array, extract four bytes and build a long
uint32_t SFE_UBLOX_GPS::extractLong(uint8_t spotToStart)
{
  uint32_t val = 0;
  val |= (uint32_t)payloadCfg[spotToStart + 0] << 8 * 0;
  val |= (uint32_t)payloadCfg[spotToStart + 1] << 8 * 1;
  val |= (uint32_t)payloadCfg[spotToStart + 2] << 8 * 2;
  val |= (uint32_t)payloadCfg[spotToStart + 3] << 8 * 3;
  return (val);
}

//Given a spot in the payload array, extract two bytes and build an int
uint16_t SFE_UBLOX_GPS::extractInt(uint8_t spotToStart)
{
  uint16_t val = 0;
  val |= (uint16_t)payloadCfg[spotToStart + 0] << 8 * 0;
  val |= (uint16_t)payloadCfg[spotToStart + 1] << 8 * 1;
  return (val);
}

//Given a spot, extract a byte from the payload
uint8_t SFE_UBLOX_GPS::extractByte(uint8_t spotToStart)
{
  return (payloadCfg[spotToStart]);
}

//Given a spot, extract a signed 8-bit value from the payload
int8_t SFE_UBLOX_GPS::extractSignedChar(uint8_t spotToStart)
{
  return ((int8_t)payloadCfg[spotToStart]);
}

//Get the current year
uint16_t SFE_UBLOX_GPS::getYear(uint16_t maxWait)
{
  if (moduleQueried.gpsYear == false)
    getPVT(maxWait);
  moduleQueried.gpsYear = false; //Since we are about to give this to user, mark this data as stale
  return (gpsYear);
}

//Get the current month
uint8_t SFE_UBLOX_GPS::getMonth(uint16_t maxWait)
{
  if (moduleQueried.gpsMonth == false)
    getPVT(maxWait);
  moduleQueried.gpsMonth = false; //Since we are about to give this to user, mark this data as stale
  return (gpsMonth);
}

//Get the current day
uint8_t SFE_UBLOX_GPS::getDay(uint16_t maxWait)
{
  if (moduleQueried.gpsDay == false)
    getPVT(maxWait);
  moduleQueried.gpsDay = false; //Since we are about to give this to user, mark this data as stale
  return (gpsDay);
}

//Get the current hour
uint8_t SFE_UBLOX_GPS::getHour(uint16_t maxWait)
{
  if (moduleQueried.gpsHour == false)
    getPVT(maxWait);
  moduleQueried.gpsHour = false; //Since we are about to give this to user, mark this data as stale
  return (gpsHour);
}

//Get the current minute
uint8_t SFE_UBLOX_GPS::getMinute(uint16_t maxWait)
{
  if (moduleQueried.gpsMinute == false)
    getPVT(maxWait);
  moduleQueried.gpsMinute = false; //Since we are about to give this to user, mark this data as stale
  return (gpsMinute);
}

//Get the current second
uint8_t SFE_UBLOX_GPS::getSecond(uint16_t maxWait)
{
  if (moduleQueried.gpsSecond == false)
    getPVT(maxWait);
  moduleQueried.gpsSecond = false; //Since we are about to give this to user, mark this data as stale
  return (gpsSecond);
}

//Get the current millisecond
uint16_t SFE_UBLOX_GPS::getMillisecond(uint16_t maxWait)
{
  if (moduleQueried.gpsiTOW == false)
    getPVT(maxWait);
  moduleQueried.gpsiTOW = false; //Since we are about to give this to user, mark this data as stale
  return (gpsMillisecond);
}

//Get the current nanoseconds - includes milliseconds
int32_t SFE_UBLOX_GPS::getNanosecond(uint16_t maxWait)
{
  if (moduleQueried.gpsNanosecond == false)
    getPVT(maxWait);
  moduleQueried.gpsNanosecond = false; //Since we are about to give this to user, mark this data as stale
  return (gpsNanosecond);
}

//Get the latest Position/Velocity/Time solution and fill all global variables
boolean SFE_UBLOX_GPS::getPVT(uint16_t maxWait)
{
  if (autoPVT && autoPVTImplicitUpdate)
  {
    //The GPS is automatically reporting, we just check whether we got unread data
    if (_printDebug == true)
    {
      _debugSerial->println(F("getPVT: Autoreporting"));
    }
    checkUblox();
    return moduleQueried.all;
  }
  else if (autoPVT && !autoPVTImplicitUpdate)
  {
    //Someone else has to call checkUblox for us...
    if (_printDebug == true)
    {
      _debugSerial->println(F("getPVT: Exit immediately"));
    }
    return (false);
  }
  else
  {
    if (_printDebug == true)
    {
      _debugSerial->println(F("getPVT: Polling"));
    }

    //The GPS is not automatically reporting navigation position so we have to poll explicitly
    packetCfg.cls = UBX_CLASS_NAV;
    packetCfg.id = UBX_NAV_PVT;
    packetCfg.len = 0;
    //packetCfg.startingSpot = 20; //Begin listening at spot 20 so we can record up to 20+MAX_PAYLOAD_SIZE = 84 bytes Note:now hard-coded in processUBX

    //The data is parsed as part of processing the response
    sfe_ublox_status_e retVal = sendCommand(packetCfg, maxWait);

    if (retVal == SFE_UBLOX_STATUS_DATA_RECEIVED)
      return (true);

    if (_printDebug == true)
    {
      _debugSerial->print(F("getPVT retVal: "));
      _debugSerial->println(statusString(retVal));
    }
    return (false);
  }
}

uint32_t SFE_UBLOX_GPS::getTimeOfWeek(uint16_t maxWait /* = 250*/)
{
  if (moduleQueried.gpsiTOW == false)
    getPVT(maxWait);
  moduleQueried.gpsiTOW = false; //Since we are about to give this to user, mark this data as stale
  return (timeOfWeek);
}

int32_t SFE_UBLOX_GPS::getHighResLatitude(uint16_t maxWait /* = 250*/)
{
  if (highResModuleQueried.highResLatitude == false)
    getHPPOSLLH(maxWait);
  highResModuleQueried.highResLatitude = false; //Since we are about to give this to user, mark this data as stale
  return (highResLatitude);
}

int8_t SFE_UBLOX_GPS::getHighResLatitudeHp(uint16_t maxWait /* = 250*/)
{
  if (highResModuleQueried.highResLatitudeHp == false)
    getHPPOSLLH(maxWait);
  highResModuleQueried.highResLatitudeHp = false; //Since we are about to give this to user, mark this data as stale
  return (highResLatitudeHp);
}

int32_t SFE_UBLOX_GPS::getHighResLongitude(uint16_t maxWait /* = 250*/)
{
  if (highResModuleQueried.highResLongitude == false)
    getHPPOSLLH(maxWait);
  highResModuleQueried.highResLongitude = false; //Since we are about to give this to user, mark this data as stale
  return (highResLongitude);
}

int8_t SFE_UBLOX_GPS::getHighResLongitudeHp(uint16_t maxWait /* = 250*/)
{
  if (highResModuleQueried.highResLongitudeHp == false)
    getHPPOSLLH(maxWait);
  highResModuleQueried.highResLongitudeHp = false; //Since we are about to give this to user, mark this data as stale
  return (highResLongitudeHp);
}

int32_t SFE_UBLOX_GPS::getElipsoid(uint16_t maxWait /* = 250*/)
{
  if (highResModuleQueried.elipsoid == false)
    getHPPOSLLH(maxWait);
  highResModuleQueried.elipsoid = false; //Since we are about to give this to user, mark this data as stale
  return (elipsoid);
}

int8_t SFE_UBLOX_GPS::getElipsoidHp(uint16_t maxWait /* = 250*/)
{
  if (highResModuleQueried.elipsoidHp == false)
    getHPPOSLLH(maxWait);
  highResModuleQueried.elipsoidHp = false; //Since we are about to give this to user, mark this data as stale
  return (elipsoidHp);
}

int32_t SFE_UBLOX_GPS::getMeanSeaLevel(uint16_t maxWait /* = 250*/)
{
  if (highResModuleQueried.meanSeaLevel == false)
    getHPPOSLLH(maxWait);
  highResModuleQueried.meanSeaLevel = false; //Since we are about to give this to user, mark this data as stale
  return (meanSeaLevel);
}

int8_t SFE_UBLOX_GPS::getMeanSeaLevelHp(uint16_t maxWait /* = 250*/)
{
  if (highResModuleQueried.meanSeaLevelHp == false)
    getHPPOSLLH(maxWait);
  highResModuleQueried.meanSeaLevelHp = false; //Since we are about to give this to user, mark this data as stale
  return (meanSeaLevelHp);
}

// getGeoidSeparation is currently redundant. The geoid separation seems to only be provided in NMEA GGA and GNS messages.
int32_t SFE_UBLOX_GPS::getGeoidSeparation(uint16_t maxWait /* = 250*/)
{
  if (highResModuleQueried.geoidSeparation == false)
    getHPPOSLLH(maxWait);
  highResModuleQueried.geoidSeparation = false; //Since we are about to give this to user, mark this data as stale
  return (geoidSeparation);
}

uint32_t SFE_UBLOX_GPS::getHorizontalAccuracy(uint16_t maxWait /* = 250*/)
{
  if (highResModuleQueried.horizontalAccuracy == false)
    getHPPOSLLH(maxWait);
  highResModuleQueried.horizontalAccuracy = false; //Since we are about to give this to user, mark this data as stale
  return (horizontalAccuracy);
}

uint32_t SFE_UBLOX_GPS::getVerticalAccuracy(uint16_t maxWait /* = 250*/)
{
  if (highResModuleQueried.verticalAccuracy == false)
    getHPPOSLLH(maxWait);
  highResModuleQueried.verticalAccuracy = false; //Since we are about to give this to user, mark this data as stale
  return (verticalAccuracy);
}

boolean SFE_UBLOX_GPS::getHPPOSLLH(uint16_t maxWait)
{
  //The GPS is not automatically reporting navigation position so we have to poll explicitly
  packetCfg.cls = UBX_CLASS_NAV;
  packetCfg.id = UBX_NAV_HPPOSLLH;
  packetCfg.len = 0;

  return (sendCommand(packetCfg, maxWait) == SFE_UBLOX_STATUS_DATA_RECEIVED); // We are only expecting data (no ACK)
}

//Get the current 3D high precision positional accuracy - a fun thing to watch
//Returns a long representing the 3D accuracy in millimeters
uint32_t SFE_UBLOX_GPS::getPositionAccuracy(uint16_t maxWait)
{
  packetCfg.cls = UBX_CLASS_NAV;
  packetCfg.id = UBX_NAV_HPPOSECEF;
  packetCfg.len = 0;
  packetCfg.startingSpot = 0;

  if (sendCommand(packetCfg, maxWait) != SFE_UBLOX_STATUS_DATA_RECEIVED) // We are only expecting data (no ACK)
    return (0); //If command send fails then bail

  uint32_t tempAccuracy = extractLong(24); //We got a response, now extract a long beginning at a given position

  if ((tempAccuracy % 10) >= 5)
    tempAccuracy += 5; //Round fraction of mm up to next mm if .5 or above
  tempAccuracy /= 10;  //Convert 0.1mm units to mm

  return (tempAccuracy);
}

//Get the current latitude in degrees
//Returns a long representing the number of degrees *10^-7
int32_t SFE_UBLOX_GPS::getLatitude(uint16_t maxWait)
{
  if (moduleQueried.latitude == false)
    getPVT(maxWait);
  moduleQueried.latitude = false; //Since we are about to give this to user, mark this data as stale
  moduleQueried.all = false;

  return (latitude);
}

//Get the current longitude in degrees
//Returns a long representing the number of degrees *10^-7
int32_t SFE_UBLOX_GPS::getLongitude(uint16_t maxWait)
{
  if (moduleQueried.longitude == false)
    getPVT(maxWait);
  moduleQueried.longitude = false; //Since we are about to give this to user, mark this data as stale
  moduleQueried.all = false;

  return (longitude);
}

//Get the current altitude in mm according to ellipsoid model
int32_t SFE_UBLOX_GPS::getAltitude(uint16_t maxWait)
{
  if (moduleQueried.altitude == false)
    getPVT(maxWait);
  moduleQueried.altitude = false; //Since we are about to give this to user, mark this data as stale
  moduleQueried.all = false;

  return (altitude);
}

//Get the current altitude in mm according to mean sea level
//Ellipsoid model: https://www.esri.com/news/arcuser/0703/geoid1of3.html
//Difference between Ellipsoid Model and Mean Sea Level: https://eos-gnss.com/elevation-for-beginners/
int32_t SFE_UBLOX_GPS::getAltitudeMSL(uint16_t maxWait)
{
  if (moduleQueried.altitudeMSL == false)
    getPVT(maxWait);
  moduleQueried.altitudeMSL = false; //Since we are about to give this to user, mark this data as stale
  moduleQueried.all = false;

  return (altitudeMSL);
}

//Get the number of satellites used in fix
uint8_t SFE_UBLOX_GPS::getSIV(uint16_t maxWait)
{
  if (moduleQueried.SIV == false)
    getPVT(maxWait);
  moduleQueried.SIV = false; //Since we are about to give this to user, mark this data as stale
  moduleQueried.all = false;

  return (SIV);
}

//Get the current fix type
//0=no fix, 1=dead reckoning, 2=2D, 3=3D, 4=GNSS, 5=Time fix
uint8_t SFE_UBLOX_GPS::getFixType(uint16_t maxWait)
{
  if (moduleQueried.fixType == false)
  {
    getPVT(maxWait);
  }
  moduleQueried.fixType = false; //Since we are about to give this to user, mark this data as stale
  moduleQueried.all = false;

  return (fixType);
}

//Get the carrier phase range solution status
//Useful when querying module to see if it has high-precision RTK fix
//0=No solution, 1=Float solution, 2=Fixed solution
uint8_t SFE_UBLOX_GPS::getCarrierSolutionType(uint16_t maxWait)
{
  if (moduleQueried.carrierSolution == false)
    getPVT(maxWait);
  moduleQueried.carrierSolution = false; //Since we are about to give this to user, mark this data as stale
  moduleQueried.all = false;

  return (carrierSolution);
}

//Get the ground speed in mm/s
int32_t SFE_UBLOX_GPS::getGroundSpeed(uint16_t maxWait)
{
  if (moduleQueried.groundSpeed == false)
    getPVT(maxWait);
  moduleQueried.groundSpeed = false; //Since we are about to give this to user, mark this data as stale
  moduleQueried.all = false;

  return (groundSpeed);
}

//Get the heading of motion (as opposed to heading of car) in degrees * 10^-5
int32_t SFE_UBLOX_GPS::getHeading(uint16_t maxWait)
{
  if (moduleQueried.headingOfMotion == false)
    getPVT(maxWait);
  moduleQueried.headingOfMotion = false; //Since we are about to give this to user, mark this data as stale
  moduleQueried.all = false;

  return (headingOfMotion);
}

//Get the positional dillution of precision * 10^-2
uint16_t SFE_UBLOX_GPS::getPDOP(uint16_t maxWait)
{
  if (moduleQueried.pDOP == false)
    getPVT(maxWait);
  moduleQueried.pDOP = false; //Since we are about to give this to user, mark this data as stale
  moduleQueried.all = false;

  return (pDOP);
}

//Get the current protocol version of the Ublox module we're communicating with
//This is helpful when deciding if we should call the high-precision Lat/Long (HPPOSLLH) or the regular (POSLLH)
uint8_t SFE_UBLOX_GPS::getProtocolVersionHigh(uint16_t maxWait)
{
  if (moduleQueried.versionNumber == false)
    getProtocolVersion(maxWait);
  return (versionHigh);
}

//Get the current protocol version of the Ublox module we're communicating with
//This is helpful when deciding if we should call the high-precision Lat/Long (HPPOSLLH) or the regular (POSLLH)
uint8_t SFE_UBLOX_GPS::getProtocolVersionLow(uint16_t maxWait)
{
  if (moduleQueried.versionNumber == false)
    getProtocolVersion(maxWait);
  return (versionLow);
}

//Get the current protocol version of the Ublox module we're communicating with
//This is helpful when deciding if we should call the high-precision Lat/Long (HPPOSLLH) or the regular (POSLLH)
boolean SFE_UBLOX_GPS::getProtocolVersion(uint16_t maxWait)
{
  //Send packet with only CLS and ID, length of zero. This will cause the module to respond with the contents of that CLS/ID.
  packetCfg.cls = UBX_CLASS_MON;
  packetCfg.id = UBX_MON_VER;

  packetCfg.len = 0;
  packetCfg.startingSpot = 40; //Start at first "extended software information" string

  if (sendCommand(packetCfg, maxWait) != SFE_UBLOX_STATUS_DATA_RECEIVED) // We are only expecting data (no ACK)
    return (false); //If command send fails then bail

  //Payload should now contain ~220 characters (depends on module type)

  // if (_printDebug == true)
  // {
  //   _debugSerial->print(F("MON VER Payload:"));
  //   for (int location = 0; location < packetCfg.len; location++)
  //   {
  //     if (location % 30 == 0)
  //       _debugSerial->println();
  //     _debugSerial->write(payloadCfg[location]);
  //   }
  //   _debugSerial->println();
  // }

  //We will step through the payload looking at each extension field of 30 bytes
  for (uint8_t extensionNumber = 0; extensionNumber < 10; extensionNumber++)
  {
    //Now we need to find "PROTVER=18.00" in the incoming byte stream
    if (payloadCfg[(30 * extensionNumber) + 0] == 'P' && payloadCfg[(30 * extensionNumber) + 6] == 'R')
    {
      versionHigh = (payloadCfg[(30 * extensionNumber) + 8] - '0') * 10 + (payloadCfg[(30 * extensionNumber) + 9] - '0');  //Convert '18' to 18
      versionLow = (payloadCfg[(30 * extensionNumber) + 11] - '0') * 10 + (payloadCfg[(30 * extensionNumber) + 12] - '0'); //Convert '00' to 00
      moduleQueried.versionNumber = true;                                                                                  //Mark this data as new

      if (_printDebug == true)
      {
        _debugSerial->print(F("Protocol version: "));
        _debugSerial->print(versionHigh);
        _debugSerial->print(F("."));
        _debugSerial->println(versionLow);
      }
      return (true); //Success!
    }
  }

  return (false); //We failed
}

//Mark all the PVT data as read/stale. This is handy to get data alignment after CRC failure
void SFE_UBLOX_GPS::flushPVT()
{
  //Mark all datums as stale (read before)
  moduleQueried.gpsiTOW = false;
  moduleQueried.gpsYear = false;
  moduleQueried.gpsMonth = false;
  moduleQueried.gpsDay = false;
  moduleQueried.gpsHour = false;
  moduleQueried.gpsMinute = false;
  moduleQueried.gpsSecond = false;
  moduleQueried.gpsNanosecond = false;

  moduleQueried.all = false;
  moduleQueried.longitude = false;
  moduleQueried.latitude = false;
  moduleQueried.altitude = false;
  moduleQueried.altitudeMSL = false;
  moduleQueried.SIV = false;
  moduleQueried.fixType = false;
  moduleQueried.carrierSolution = false;
  moduleQueried.groundSpeed = false;
  moduleQueried.headingOfMotion = false;
  moduleQueried.pDOP = false;
}

//Relative Positioning Information in NED frame
//Returns true if commands was successful
boolean SFE_UBLOX_GPS::getRELPOSNED(uint16_t maxWait)
{
  packetCfg.cls = UBX_CLASS_NAV;
  packetCfg.id = UBX_NAV_RELPOSNED;
  packetCfg.len = 0;
  packetCfg.startingSpot = 0;

  if (sendCommand(packetCfg, maxWait) != SFE_UBLOX_STATUS_DATA_RECEIVED) // We are only expecting data (no ACK)
    return (false); //If command send fails then bail

  //We got a response, now parse the bits

  uint16_t refStationID = extractInt(2);
  //_debugSerial->print(F("refStationID: "));
  //_debugSerial->println(refStationID));

  int32_t tempRelPos;

  tempRelPos = extractLong(8);
  relPosInfo.relPosN = tempRelPos / 100.0; //Convert cm to m

  tempRelPos = extractLong(12);
  relPosInfo.relPosE = tempRelPos / 100.0; //Convert cm to m

  tempRelPos = extractLong(16);
  relPosInfo.relPosD = tempRelPos / 100.0; //Convert cm to m

  relPosInfo.relPosLength = extractLong(20);
  relPosInfo.relPosHeading = extractLong(24);

  relPosInfo.relPosHPN = payloadCfg[32];
  relPosInfo.relPosHPE = payloadCfg[33];
  relPosInfo.relPosHPD = payloadCfg[34];
  relPosInfo.relPosHPLength = payloadCfg[35];

  uint32_t tempAcc;

  tempAcc = extractLong(36);
  relPosInfo.accN = tempAcc / 10000.0; //Convert 0.1 mm to m

  tempAcc = extractLong(40);
  relPosInfo.accE = tempAcc / 10000.0; //Convert 0.1 mm to m

  tempAcc = extractLong(44);
  relPosInfo.accD = tempAcc / 10000.0; //Convert 0.1 mm to m

  uint8_t flags = payloadCfg[60];

  relPosInfo.gnssFixOk = flags & (1 << 0);
  relPosInfo.diffSoln = flags & (1 << 1);
  relPosInfo.relPosValid = flags & (1 << 2);
  relPosInfo.carrSoln = (flags & (0b11 << 3)) >> 3;
  relPosInfo.isMoving = flags & (1 << 5);
  relPosInfo.refPosMiss = flags & (1 << 6);
  relPosInfo.refObsMiss = flags & (1 << 7);

  return (true);
}