Example16_Nanosecond_MaxOutput.ino

/*
  Getting time and date using Ublox commands
  By: davidallenmann
  SparkFun Electronics
  Date: April 16th, 2019
  License: MIT. See license file for more information but you can
  basically do whatever you want with this code.

  This example shows how to query a Ublox module for the current time and date. We also
  turn off the NMEA output on the I2C port. This decreases the amount of I2C traffic
  dramatically.

  Leave NMEA parsing behind. Now you can simply ask the module for the datums you want!

  Feel like supporting open source hardware?
  Buy a board from SparkFun!
  ZED-F9P RTK2: https://www.sparkfun.com/products/15136
  NEO-M8P RTK: https://www.sparkfun.com/products/15005
  SAM-M8Q: https://www.sparkfun.com/products/15106

  Hardware Connections:
  Plug a Qwiic cable into the GPS and a BlackBoard
  If you don't have a platform with a Qwiic connection use the SparkFun Qwiic Breadboard Jumper (https://www.sparkfun.com/products/14425)
  Open the serial monitor at 115200 baud to see the output
*/

#include <Wire.h> //Needed for I2C to GPS

#include "SparkFun_Ublox_Arduino_Library.h" //http://librarymanager/All#SparkFun_Ublox_GPS
SFE_UBLOX_GPS myGPS;

long lastTime = 0; //Simple local timer. Limits amount if I2C traffic to Ublox module.

void setup()
{
  Serial.begin(500000); //Increase serial speed to maximize 
  while (!Serial)
    ; //Wait for user to open terminal
  Serial.println("SparkFun Ublox Example");

  Wire.begin();
  Wire.setClock(400000);
  
  if (myGPS.begin() == false) //Connect to the Ublox module using Wire port
  {
    Serial.println(F("Ublox GPS not detected at default I2C address. Please check wiring. Freezing."));
    while (1)
      ;
  }

  myGPS.setI2COutput(COM_TYPE_UBX); //Set the I2C port to output UBX only (turn off NMEA noise)
  myGPS.saveConfiguration();        //Save the current settings to flash and BBR

  //myGPS.enableDebugging(); //Enable debug messages over Serial (default)

  myGPS.setNavigationFrequency(10); //Set output to 10 times a second
  byte rate = myGPS.getNavigationFrequency(); //Get the update rate of this module
  Serial.print("Current update rate:");
  Serial.println(rate);
  
}

void loop()
{
  //Query module only every second. Doing it more often will just cause I2C traffic.
  //The module only responds when a new position is available
  if (millis() - lastTime > 10)
  {
    lastTime = millis(); //Update the timer

    long latitude = myGPS.getLatitude();
    Serial.print(F("Lat: "));
    Serial.print(latitude);

    long longitude = myGPS.getLongitude();
    Serial.print(F(" Long: "));
    Serial.print(longitude);
    Serial.print(F(" (degrees * 10^-7)"));

    long altitude = myGPS.getAltitude();
    Serial.print(F(" Alt: "));
    Serial.print(altitude);
    Serial.print(F(" (mm)"));

    byte SIV = myGPS.getSIV();
    Serial.print(F(" SIV: "));
    Serial.print(SIV);

    Serial.print(myGPS.getYear());
    Serial.print("-");
    Serial.print(myGPS.getMonth());
    Serial.print("-");
    Serial.print(myGPS.getDay());
    Serial.print(" ");
    Serial.print(myGPS.getHour());
    Serial.print(":");
    Serial.print(myGPS.getMinute());
    Serial.print(":");
    Serial.print(myGPS.getSecond());
    Serial.print(".");
    Serial.print(myGPS.getNanosecond());

    Serial.println();
  }
}