You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
[](https://www.sparkfun.com/products/20168)
4
+
[](https://www.sparkfun.com/products/24408)
5
5
6
-
*[SparkFun Thing Plus - ESP32 WROOM (USB-C) (WRL-20168)](https://www.sparkfun.com/products/20168)*
6
+
*[SparkFun Thing Plus - ESP32-S3) (WRL-24408)](https://www.sparkfun.com/products/24408)*
7
7
8
-
The [SparkFun Thing Plus - ESP32 WROOM (USB-C)](https://www.sparkfun.com/products/20168) is a comprehensive development platform for [Espressif's ESP32](https://espressif.com/en/products/hardware/esp32/overview). Thanks to the onboard ESP32 WROOM module, the SparkFun Thing Plus features 16MB of flash memory, 520kB of internal SRAM, an integrated 802.11 BGN WiFi transceiver and dual-mode Bluetooth capabilities, a JST connector to plug in a LiPo battery, a Qwiic connector, and 21 I/O pins. Add to that a rich set of peripherals ranging from capacitive touch sensors, Hall sensors, SD card interface, Ethernet, high-speed SPIs, UARTs, I2S, and I<sup>2</sup>C.
8
+
The [SparkFun Thing Plus - ESP32-S3](https://www.sparkfun.com/products/24408) brings a powerful and versatile IoT development platform to the Thing Plus product line. It features the ESP32 WROOM-S3 MINI wireless module from espressif<sup>™</sup>. The ESP32 WROOM-S3 is built around an Xtensa<sup>®</sup> 32-bit LX7 processor with massive processing power that operates at up to 240 MHz. It supports both 2.4 GHz WiFi and Bluetooth<sup>®</sup> 5 (LE) with a built-in PCB antenna. This version of the ESP32-S3 has 4MB Flash memory and 2MB of dynamic/PSRAM and the board also has with a µSD card slot for those who need more storage space.
9
+
10
+
The module has a large set of peripherals including UART, I<sup>2</sup>C, SPI, LCD control, SDIO host, TWAI<sup>®</sup> controller (compatible
11
+
with ISO 11898-1, i.e., CAN Specification 2.), and more. The module allows for customizing which GPIO pins these peripherals operate on though some are limited to specific pins. The ESP32-S3 can run two USB ports simultaneously and can even act as a USB host host device.
12
+
13
+
The Thing Plus footprint breaks out all of the ESP32-C6's 23 GPIO pins to a pair 0.1"-spaced plated through hole (PTH) headers. The board also has a USB-C connector for primary power and programming, 2-pin JST connector for a LiPo battery (not included), a microSD card slot for expanded storage, and a Qwiic connector to integrate it into SparkFun's [Qwiic ecosystem](https://www.sparkfun.com/qwiic). It also includes a charging circuit and fuel gauge for charging and monitoring an attached LiPo battery.
9
14
10
-
We took all the good from the original [ESP32 Thing Plus](https://www.sparkfun.com/products/15663) and sprinkled on some more. We upgraded to a USB-C connector that provides up to 2A of power, added a fuel gauge IC that will make sure you know your battery levels, included a NeoPixel (WS2812C) RGB LED is the perfect multi-status indicator, and threw a microSD connector on the back! Oh, and the new taller reset and boot buttons are **so** much easier to push! We even dedicated a voltage regulator to the Qwiic connector, which enables software power control to the Qwiic bus - great for low power logging!
11
15
12
16
13
17
Repository Contents
14
18
-------------------
15
19
20
+
***[/Documents](/Documents/)** - Datasheets, additional product information
0 commit comments