STM32WLx_Transmit_Interrupt.ino

/*
  RadioLib STM32WLx Transmit with Interrupts Example

  This example transmits LoRa packets with one second delays
  between them. Each packet contains up to 256 bytes
  of data, in the form of:
  - Arduino String
  - null-terminated char array (C-string)
  - arbitrary binary data (byte array)

  For default module settings, see the wiki page
  https://github.com/jgromes/RadioLib/wiki/Default-configuration#sx126x---lora-modem

  For full API reference, see the GitHub Pages
  https://jgromes.github.io/RadioLib/
*/

// include the library
#include <RadioLib.h>

// no need to configure pins, signals are routed to the radio internally
STM32WLx radio = new STM32WLx_Module();

// set RF switch configuration for Nucleo WL55JC1
// NOTE: other boards may be different!
//       Some boards may not have either LP or HP.
//       For those, do not set the LP/HP entry in the table.
static const uint32_t rfswitch_pins[] =
                         {PC3,  PC4,  PC5, RADIOLIB_NC, RADIOLIB_NC};
static const Module::RfSwitchMode_t rfswitch_table[] = {
  {STM32WLx::MODE_IDLE,  {LOW,  LOW,  LOW}},
  {STM32WLx::MODE_RX,    {HIGH, HIGH, LOW}},
  {STM32WLx::MODE_TX_LP, {HIGH, HIGH, HIGH}},
  {STM32WLx::MODE_TX_HP, {HIGH, LOW,  HIGH}},
  END_OF_MODE_TABLE,
};

// save transmission state between loops
int transmissionState = RADIOLIB_ERR_NONE;

// flag to indicate that a packet was sent
volatile bool transmittedFlag = false;

// this function is called when a complete packet
// is transmitted by the module
// IMPORTANT: this function MUST be 'void' type
//            and MUST NOT have any arguments!
void setFlag(void) {
  // we sent a packet, set the flag
  transmittedFlag = true;
}

void setup() {
  Serial.begin(9600);

  // set RF switch control configuration
  // this has to be done prior to calling begin()
  radio.setRfSwitchTable(rfswitch_pins, rfswitch_table);

  // initialize STM32WL with default settings, except frequency
  Serial.print(F("[STM32WL] Initializing ... "));
  int state = radio.begin(868.0);
  if (state == RADIOLIB_ERR_NONE) {
    Serial.println(F("success!"));
  } else {
    Serial.print(F("failed, code "));
    Serial.println(state);
    while (true) { delay(10); }
  }

  // set appropriate TCXO voltage for Nucleo WL55JC1
  state = radio.setTCXO(1.7);
  if (state == RADIOLIB_ERR_NONE) {
    Serial.println(F("success!"));
  } else {
    Serial.print(F("failed, code "));
    Serial.println(state);
    while (true) { delay(10); }
  }

  // set the function that will be called
  // when packet transmission is finished
  radio.setDio1Action(setFlag);

  // start transmitting the first packet
  Serial.print(F("[STM32WL] Sending first packet ... "));

  // you can transmit C-string or Arduino string up to
  // 256 characters long
  transmissionState = radio.startTransmit("Hello World!");

  // you can also transmit byte array up to 256 bytes long
  /*
    byte byteArr[] = {0x01, 0x23, 0x45, 0x67,
                      0x89, 0xAB, 0xCD, 0xEF};
    state = radio.startTransmit(byteArr, 8);
  */
}

// counter to keep track of transmitted packets
int count = 0;

void loop() {
  // check if the previous transmission finished
  if(transmittedFlag) {
    // reset flag
    transmittedFlag = false;

    if (transmissionState == RADIOLIB_ERR_NONE) {
      // packet was successfully sent
      Serial.println(F("transmission finished!"));

      // NOTE: when using interrupt-driven transmit method,
      //       it is not possible to automatically measure
      //       transmission data rate using getDataRate()

    } else {
      Serial.print(F("failed, code "));
      Serial.println(transmissionState);

    }

    // clean up after transmission is finished
    // this will ensure transmitter is disabled,
    // RF switch is powered down etc.
    radio.finishTransmit();

    // wait a second before transmitting again
    delay(1000);

    // send another one
    Serial.print(F("[STM32WL] Sending another packet ... "));

    // you can transmit C-string or Arduino string up to
    // 256 characters long
    String str = "Hello World! #" + String(count++);
    transmissionState = radio.startTransmit(str);

    // you can also transmit byte array up to 256 bytes long
    /*
      byte byteArr[] = {0x01, 0x23, 0x45, 0x67,
                        0x89, 0xAB, 0xCD, 0xEF};
      transmissionState = radio.startTransmit(byteArr, 8);
    */
  }
}