Added The Teensy 4.1 board

The Teensy 4.1 board has an 8MB W25Q64JV as opposed to the 2MB flash
on the Teensy 4.0.  This largely doensn't matter for TinyUsb, except
when you attempt to access any memory in the flash above the 2MB
boundary, when it fails with a hard fault.

Author: ccrome

hw/bsp/imxrt/boards/teensy_41/board.h

@@ -0,0 +1,52 @@
+/* 
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2019, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+
+// required since iMX RT10xx SDK include this file for board size
+#define BOARD_FLASH_SIZE (8 * 1024 * 1024)
+
+// LED
+#define LED_PINMUX            IOMUXC_GPIO_B0_03_GPIO2_IO03 // D13
+#define LED_PORT              GPIO2
+#define LED_PIN               3
+#define LED_STATE_ON          0
+
+// no button
+#define BUTTON_PINMUX         IOMUXC_GPIO_B0_01_GPIO2_IO01 // D12
+#define BUTTON_PORT           GPIO2
+#define BUTTON_PIN            1
+#define BUTTON_STATE_ACTIVE   0
+
+// UART
+#define UART_PORT             LPUART6
+#define UART_RX_PINMUX        IOMUXC_GPIO_AD_B0_03_LPUART6_RX  // D0
+#define UART_TX_PINMUX        IOMUXC_GPIO_AD_B0_02_LPUART6_TX  // D1
+
+#endif /* BOARD_H_ */

hw/bsp/imxrt/boards/teensy_41/board.mk

@@ -0,0 +1,10 @@
+CFLAGS += -DCPU_MIMXRT1062DVL6A
+MCU_VARIANT = MIMXRT1062
+
+# For flash-jlink target
+JLINK_DEVICE = MIMXRT1062xxx6A
+
+# flash by using teensy_loader_cli https://github.com/PaulStoffregen/teensy_loader_cli
+# Make sure it is in your PATH 
+flash: $(BUILD)/$(PROJECT).hex
+	teensy_loader_cli --mcu=imxrt1062 -v -w $<

hw/bsp/imxrt/boards/teensy_41/teensy41_flexspi_nor_config.c

@@ -0,0 +1,49 @@
+/*
+ * Copyright 2018 NXP
+ * All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <bsp/imxrt/boards/teensy_40/teensy40_flexspi_nor_config.h>
+
+/* Component ID definition, used by tools. */
+#ifndef FSL_COMPONENT_ID
+#define FSL_COMPONENT_ID "platform.drivers.xip_board"
+#endif
+
+/*******************************************************************************
+ * Code
+ ******************************************************************************/
+#if defined(XIP_BOOT_HEADER_ENABLE) && (XIP_BOOT_HEADER_ENABLE == 1)
+#if defined(__CC_ARM) || defined(__ARMCC_VERSION) || defined(__GNUC__)
+__attribute__((section(".boot_hdr.conf")))
+#elif defined(__ICCARM__)
+#pragma location = ".boot_hdr.conf"
+#endif
+
+const flexspi_nor_config_t qspiflash_config = {
+    .memConfig =
+        {
+            .tag              = FLEXSPI_CFG_BLK_TAG,
+            .version          = FLEXSPI_CFG_BLK_VERSION,
+            .readSampleClkSrc = kFlexSPIReadSampleClk_LoopbackFromDqsPad,
+            .csHoldTime       = 3u,
+            .csSetupTime      = 3u,
+            // Enable DDR mode, Wordaddassable, Safe configuration, Differential clock
+            .sflashPadType = kSerialFlash_4Pads,
+            .serialClkFreq = kFlexSpiSerialClk_100MHz,
+            .sflashA1Size  = 8u * 1024u * 1024u,
+            .lookupTable =
+                {
+                    // Read LUTs
+                    FLEXSPI_LUT_SEQ(CMD_SDR, FLEXSPI_1PAD, 0xEB, RADDR_SDR, FLEXSPI_4PAD, 0x18),
+                    FLEXSPI_LUT_SEQ(DUMMY_SDR, FLEXSPI_4PAD, 0x06, READ_SDR, FLEXSPI_4PAD, 0x04),
+                },
+        },
+    .pageSize           = 256u,
+    .sectorSize         = 4u * 1024u,
+    .blockSize          = 256u * 1024u,
+    .isUniformBlockSize = false,
+};
+#endif /* XIP_BOOT_HEADER_ENABLE */

hw/bsp/imxrt/boards/teensy_41/teensy41_flexspi_nor_config.h

@@ -0,0 +1,268 @@
+/*
+ * Copyright 2018 NXP
+ * All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#ifndef __TEENSY40_FLEXSPI_NOR_CONFIG__
+#define __TEENSY40_FLEXSPI_NOR_CONFIG__
+
+#include <stdint.h>
+#include <stdbool.h>
+#include "fsl_common.h"
+
+/*! @name Driver version */
+/*@{*/
+/*! @brief XIP_BOARD driver version 2.0.0. */
+#define FSL_XIP_BOARD_DRIVER_VERSION (MAKE_VERSION(2, 0, 0))
+/*@}*/
+
+/* FLEXSPI memory config block related defintions */
+#define FLEXSPI_CFG_BLK_TAG (0x42464346UL)     // ascii "FCFB" Big Endian
+#define FLEXSPI_CFG_BLK_VERSION (0x56010400UL) // V1.4.0
+#define FLEXSPI_CFG_BLK_SIZE (512)
+
+/* FLEXSPI Feature related definitions */
+#define FLEXSPI_FEATURE_HAS_PARALLEL_MODE 1
+
+/* Lookup table related defintions */
+#define CMD_INDEX_READ 0
+#define CMD_INDEX_READSTATUS 1
+#define CMD_INDEX_WRITEENABLE 2
+#define CMD_INDEX_WRITE 4
+
+#define CMD_LUT_SEQ_IDX_READ 0
+#define CMD_LUT_SEQ_IDX_READSTATUS 1
+#define CMD_LUT_SEQ_IDX_WRITEENABLE 3
+#define CMD_LUT_SEQ_IDX_WRITE 9
+
+#define CMD_SDR 0x01
+#define CMD_DDR 0x21
+#define RADDR_SDR 0x02
+#define RADDR_DDR 0x22
+#define CADDR_SDR 0x03
+#define CADDR_DDR 0x23
+#define MODE1_SDR 0x04
+#define MODE1_DDR 0x24
+#define MODE2_SDR 0x05
+#define MODE2_DDR 0x25
+#define MODE4_SDR 0x06
+#define MODE4_DDR 0x26
+#define MODE8_SDR 0x07
+#define MODE8_DDR 0x27
+#define WRITE_SDR 0x08
+#define WRITE_DDR 0x28
+#define READ_SDR 0x09
+#define READ_DDR 0x29
+#define LEARN_SDR 0x0A
+#define LEARN_DDR 0x2A
+#define DATSZ_SDR 0x0B
+#define DATSZ_DDR 0x2B
+#define DUMMY_SDR 0x0C
+#define DUMMY_DDR 0x2C
+#define DUMMY_RWDS_SDR 0x0D
+#define DUMMY_RWDS_DDR 0x2D
+#define JMP_ON_CS 0x1F
+#define STOP 0
+
+#define FLEXSPI_1PAD 0
+#define FLEXSPI_2PAD 1
+#define FLEXSPI_4PAD 2
+#define FLEXSPI_8PAD 3
+
+#define FLEXSPI_LUT_SEQ(cmd0, pad0, op0, cmd1, pad1, op1)                                                              \
+    (FLEXSPI_LUT_OPERAND0(op0) | FLEXSPI_LUT_NUM_PADS0(pad0) | FLEXSPI_LUT_OPCODE0(cmd0) | FLEXSPI_LUT_OPERAND1(op1) | \
+     FLEXSPI_LUT_NUM_PADS1(pad1) | FLEXSPI_LUT_OPCODE1(cmd1))
+
+//!@brief Definitions for FlexSPI Serial Clock Frequency
+typedef enum _FlexSpiSerialClockFreq
+{
+    kFlexSpiSerialClk_30MHz  = 1,
+    kFlexSpiSerialClk_50MHz  = 2,
+    kFlexSpiSerialClk_60MHz  = 3,
+    kFlexSpiSerialClk_75MHz  = 4,
+    kFlexSpiSerialClk_80MHz  = 5,
+    kFlexSpiSerialClk_100MHz = 6,
+    kFlexSpiSerialClk_120MHz = 7,
+    kFlexSpiSerialClk_133MHz = 8,
+    kFlexSpiSerialClk_166MHz = 9,
+} flexspi_serial_clk_freq_t;
+
+//!@brief FlexSPI clock configuration type
+enum
+{
+    kFlexSpiClk_SDR, //!< Clock configure for SDR mode
+    kFlexSpiClk_DDR, //!< Clock configurat for DDR mode
+};
+
+//!@brief FlexSPI Read Sample Clock Source definition
+typedef enum _FlashReadSampleClkSource
+{
+    kFlexSPIReadSampleClk_LoopbackInternally      = 0,
+    kFlexSPIReadSampleClk_LoopbackFromDqsPad      = 1,
+    kFlexSPIReadSampleClk_LoopbackFromSckPad      = 2,
+    kFlexSPIReadSampleClk_ExternalInputFromDqsPad = 3,
+} flexspi_read_sample_clk_t;
+
+//!@brief Misc feature bit definitions
+enum
+{
+    kFlexSpiMiscOffset_DiffClkEnable            = 0, //!< Bit for Differential clock enable
+    kFlexSpiMiscOffset_Ck2Enable                = 1, //!< Bit for CK2 enable
+    kFlexSpiMiscOffset_ParallelEnable           = 2, //!< Bit for Parallel mode enable
+    kFlexSpiMiscOffset_WordAddressableEnable    = 3, //!< Bit for Word Addressable enable
+    kFlexSpiMiscOffset_SafeConfigFreqEnable     = 4, //!< Bit for Safe Configuration Frequency enable
+    kFlexSpiMiscOffset_PadSettingOverrideEnable = 5, //!< Bit for Pad setting override enable
+    kFlexSpiMiscOffset_DdrModeEnable            = 6, //!< Bit for DDR clock confiuration indication.
+};
+
+//!@brief Flash Type Definition
+enum
+{
+    kFlexSpiDeviceType_SerialNOR    = 1,    //!< Flash devices are Serial NOR
+    kFlexSpiDeviceType_SerialNAND   = 2,    //!< Flash devices are Serial NAND
+    kFlexSpiDeviceType_SerialRAM    = 3,    //!< Flash devices are Serial RAM/HyperFLASH
+    kFlexSpiDeviceType_MCP_NOR_NAND = 0x12, //!< Flash device is MCP device, A1 is Serial NOR, A2 is Serial NAND
+    kFlexSpiDeviceType_MCP_NOR_RAM  = 0x13, //!< Flash deivce is MCP device, A1 is Serial NOR, A2 is Serial RAMs
+};
+
+//!@brief Flash Pad Definitions
+enum
+{
+    kSerialFlash_1Pad  = 1,
+    kSerialFlash_2Pads = 2,
+    kSerialFlash_4Pads = 4,
+    kSerialFlash_8Pads = 8,
+};
+
+//!@brief FlexSPI LUT Sequence structure
+typedef struct _lut_sequence
+{
+    uint8_t seqNum; //!< Sequence Number, valid number: 1-16
+    uint8_t seqId;  //!< Sequence Index, valid number: 0-15
+    uint16_t reserved;
+} flexspi_lut_seq_t;
+
+//!@brief Flash Configuration Command Type
+enum
+{
+    kDeviceConfigCmdType_Generic,    //!< Generic command, for example: configure dummy cycles, drive strength, etc
+    kDeviceConfigCmdType_QuadEnable, //!< Quad Enable command
+    kDeviceConfigCmdType_Spi2Xpi,    //!< Switch from SPI to DPI/QPI/OPI mode
+    kDeviceConfigCmdType_Xpi2Spi,    //!< Switch from DPI/QPI/OPI to SPI mode
+    kDeviceConfigCmdType_Spi2NoCmd,  //!< Switch to 0-4-4/0-8-8 mode
+    kDeviceConfigCmdType_Reset,      //!< Reset device command
+};
+
+//!@brief FlexSPI Memory Configuration Block
+typedef struct _FlexSPIConfig
+{
+    uint32_t tag;               //!< [0x000-0x003] Tag, fixed value 0x42464346UL
+    uint32_t version;           //!< [0x004-0x007] Version,[31:24] -'V', [23:16] - Major, [15:8] - Minor, [7:0] - bugfix
+    uint32_t reserved0;         //!< [0x008-0x00b] Reserved for future use
+    uint8_t readSampleClkSrc;   //!< [0x00c-0x00c] Read Sample Clock Source, valid value: 0/1/3
+    uint8_t csHoldTime;         //!< [0x00d-0x00d] CS hold time, default value: 3
+    uint8_t csSetupTime;        //!< [0x00e-0x00e] CS setup time, default value: 3
+    uint8_t columnAddressWidth; //!< [0x00f-0x00f] Column Address with, for HyperBus protocol, it is fixed to 3, For
+    //! Serial NAND, need to refer to datasheet
+    uint8_t deviceModeCfgEnable; //!< [0x010-0x010] Device Mode Configure enable flag, 1 - Enable, 0 - Disable
+    uint8_t deviceModeType; //!< [0x011-0x011] Specify the configuration command type:Quad Enable, DPI/QPI/OPI switch,
+    //! Generic configuration, etc.
+    uint16_t waitTimeCfgCommands; //!< [0x012-0x013] Wait time for all configuration commands, unit: 100us, Used for
+    //! DPI/QPI/OPI switch or reset command
+    flexspi_lut_seq_t deviceModeSeq; //!< [0x014-0x017] Device mode sequence info, [7:0] - LUT sequence id, [15:8] - LUt
+    //! sequence number, [31:16] Reserved
+    uint32_t deviceModeArg;    //!< [0x018-0x01b] Argument/Parameter for device configuration
+    uint8_t configCmdEnable;   //!< [0x01c-0x01c] Configure command Enable Flag, 1 - Enable, 0 - Disable
+    uint8_t configModeType[3]; //!< [0x01d-0x01f] Configure Mode Type, similar as deviceModeTpe
+    flexspi_lut_seq_t
+        configCmdSeqs[3]; //!< [0x020-0x02b] Sequence info for Device Configuration command, similar as deviceModeSeq
+    uint32_t reserved1;   //!< [0x02c-0x02f] Reserved for future use
+    uint32_t configCmdArgs[3];     //!< [0x030-0x03b] Arguments/Parameters for device Configuration commands
+    uint32_t reserved2;            //!< [0x03c-0x03f] Reserved for future use
+    uint32_t controllerMiscOption; //!< [0x040-0x043] Controller Misc Options, see Misc feature bit definitions for more
+    //! details
+    uint8_t deviceType;    //!< [0x044-0x044] Device Type:  See Flash Type Definition for more details
+    uint8_t sflashPadType; //!< [0x045-0x045] Serial Flash Pad Type: 1 - Single, 2 - Dual, 4 - Quad, 8 - Octal
+    uint8_t serialClkFreq; //!< [0x046-0x046] Serial Flash Frequencey, device specific definitions, See System Boot
+    //! Chapter for more details
+    uint8_t lutCustomSeqEnable; //!< [0x047-0x047] LUT customization Enable, it is required if the program/erase cannot
+    //! be done using 1 LUT sequence, currently, only applicable to HyperFLASH
+    uint32_t reserved3[2];           //!< [0x048-0x04f] Reserved for future use
+    uint32_t sflashA1Size;           //!< [0x050-0x053] Size of Flash connected to A1
+    uint32_t sflashA2Size;           //!< [0x054-0x057] Size of Flash connected to A2
+    uint32_t sflashB1Size;           //!< [0x058-0x05b] Size of Flash connected to B1
+    uint32_t sflashB2Size;           //!< [0x05c-0x05f] Size of Flash connected to B2
+    uint32_t csPadSettingOverride;   //!< [0x060-0x063] CS pad setting override value
+    uint32_t sclkPadSettingOverride; //!< [0x064-0x067] SCK pad setting override value
+    uint32_t dataPadSettingOverride; //!< [0x068-0x06b] data pad setting override value
+    uint32_t dqsPadSettingOverride;  //!< [0x06c-0x06f] DQS pad setting override value
+    uint32_t timeoutInMs;            //!< [0x070-0x073] Timeout threshold for read status command
+    uint32_t commandInterval;        //!< [0x074-0x077] CS deselect interval between two commands
+    uint16_t dataValidTime[2]; //!< [0x078-0x07b] CLK edge to data valid time for PORT A and PORT B, in terms of 0.1ns
+    uint16_t busyOffset;       //!< [0x07c-0x07d] Busy offset, valid value: 0-31
+    uint16_t busyBitPolarity;  //!< [0x07e-0x07f] Busy flag polarity, 0 - busy flag is 1 when flash device is busy, 1 -
+    //! busy flag is 0 when flash device is busy
+    uint32_t lookupTable[64];           //!< [0x080-0x17f] Lookup table holds Flash command sequences
+    flexspi_lut_seq_t lutCustomSeq[12]; //!< [0x180-0x1af] Customizable LUT Sequences
+    uint32_t reserved4[4];              //!< [0x1b0-0x1bf] Reserved for future use
+} flexspi_mem_config_t;
+
+/*  */
+#define NOR_CMD_INDEX_READ CMD_INDEX_READ               //!< 0
+#define NOR_CMD_INDEX_READSTATUS CMD_INDEX_READSTATUS   //!< 1
+#define NOR_CMD_INDEX_WRITEENABLE CMD_INDEX_WRITEENABLE //!< 2
+#define NOR_CMD_INDEX_ERASESECTOR 3                     //!< 3
+#define NOR_CMD_INDEX_PAGEPROGRAM CMD_INDEX_WRITE       //!< 4
+#define NOR_CMD_INDEX_CHIPERASE 5                       //!< 5
+#define NOR_CMD_INDEX_DUMMY 6                           //!< 6
+#define NOR_CMD_INDEX_ERASEBLOCK 7                      //!< 7
+
+#define NOR_CMD_LUT_SEQ_IDX_READ CMD_LUT_SEQ_IDX_READ //!< 0  READ LUT sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_READSTATUS \
+    CMD_LUT_SEQ_IDX_READSTATUS //!< 1  Read Status LUT sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_READSTATUS_XPI \
+    2 //!< 2  Read status DPI/QPI/OPI sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_WRITEENABLE \
+    CMD_LUT_SEQ_IDX_WRITEENABLE //!< 3  Write Enable sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_WRITEENABLE_XPI \
+    4 //!< 4  Write Enable DPI/QPI/OPI sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_ERASESECTOR 5 //!< 5  Erase Sector sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_ERASEBLOCK 8  //!< 8 Erase Block sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_PAGEPROGRAM \
+    CMD_LUT_SEQ_IDX_WRITE                //!< 9  Program sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_CHIPERASE 11 //!< 11 Chip Erase sequence in lookupTable id stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_READ_SFDP 13 //!< 13 Read SFDP sequence in lookupTable id stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_RESTORE_NOCMD \
+    14 //!< 14 Restore 0-4-4/0-8-8 mode sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_EXIT_NOCMD \
+    15 //!< 15 Exit 0-4-4/0-8-8 mode sequence id in lookupTable stored in config blobk
+
+/*
+ *  Serial NOR configuration block
+ */
+typedef struct _flexspi_nor_config
+{
+    flexspi_mem_config_t memConfig; //!< Common memory configuration info via FlexSPI
+    uint32_t pageSize;              //!< Page size of Serial NOR
+    uint32_t sectorSize;            //!< Sector size of Serial NOR
+    uint8_t ipcmdSerialClkFreq;     //!< Clock frequency for IP command
+    uint8_t isUniformBlockSize;     //!< Sector/Block size is the same
+    uint8_t reserved0[2];           //!< Reserved for future use
+    uint8_t serialNorType;          //!< Serial NOR Flash type: 0/1/2/3
+    uint8_t needExitNoCmdMode;      //!< Need to exit NoCmd mode before other IP command
+    uint8_t halfClkForNonReadCmd;   //!< Half the Serial Clock for non-read command: true/false
+    uint8_t needRestoreNoCmdMode;   //!< Need to Restore NoCmd mode after IP commmand execution
+    uint32_t blockSize;             //!< Block size
+    uint32_t reserve2[11];          //!< Reserved for future use
+} flexspi_nor_config_t;
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#ifdef __cplusplus
+}
+#endif
+#endif /* __EVKMIMXRT1060_FLEXSPI_NOR_CONFIG__ */