HardwareSerial.h

/*
  HardwareSerial.h - Hardware serial library for Wiring
  Copyright (c) 2006 Nicholas Zambetti.  All right reserved.

  This library is free software; you can redistribute it and/or
  modify it under the terms of the GNU Lesser General Public
  License as published by the Free Software Foundation; either
  version 2.1 of the License, or (at your option) any later version.

  This library is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
  Lesser General Public License for more details.

  You should have received a copy of the GNU Lesser General Public
  License along with this library; if not, write to the Free Software
  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA

  Modified 28 September 2010 by Mark Sproul
  Modified 14 August 2012 by Alarus
  Modified 3 December 2013 by Matthijs Kooijman
*/

#ifndef HardwareSerial_h
#define HardwareSerial_h

#include <inttypes.h>

#include "Stream.h"

// Define constants and variables for buffering incoming serial data.  We're
// using a ring buffer (I think), in which head is the index of the location
// to which to write the next incoming character and tail is the index of the
// location from which to read.
// NOTE: a "power of 2" buffer size is reccomended to dramatically
//       optimize all the modulo operations for ring buffers.
// WARNING: When buffer sizes are increased to > 256, the buffer index
// variables are automatically increased in size, but the extra
// atomicity guards needed for that are not implemented. This will
// often work, but occasionally a race condition can occur that makes
// Serial behave erratically. See https://github.com/arduino/Arduino/issues/2405
#if !defined(SERIAL_TX_BUFFER_SIZE)
#define SERIAL_TX_BUFFER_SIZE 64
#endif
#if !defined(SERIAL_RX_BUFFER_SIZE)
#define SERIAL_RX_BUFFER_SIZE 64
#endif
#if (SERIAL_TX_BUFFER_SIZE>256)
typedef uint16_t tx_buffer_index_t;
#else
typedef uint8_t tx_buffer_index_t;
#endif
#if  (SERIAL_RX_BUFFER_SIZE>256)
typedef uint16_t rx_buffer_index_t;
#else
typedef uint8_t rx_buffer_index_t;
#endif

// Define config for Serial.begin(baud, config);
// below configs are not supported by STM32
//#define SERIAL_5N1 0x00
//#define SERIAL_5N2 0x08
//#define SERIAL_5E1 0x20
//#define SERIAL_5E2 0x28
//#define SERIAL_5O1 0x30
//#define SERIAL_5O2 0x38
//#define SERIAL_6N1 0x02
//#define SERIAL_6N2 0x0A

#ifdef UART_WORDLENGTH_7B
#define SERIAL_7N1 0x04
#define SERIAL_7N2 0x0C
#define SERIAL_6E1 0x22
#define SERIAL_6E2 0x2A
#define SERIAL_6O1 0x32
#define SERIAL_6O2 0x3A
#endif
#define SERIAL_8N1 0x06
#define SERIAL_8N2 0x0E
#define SERIAL_7E1 0x24
#define SERIAL_8E1 0x26
#define SERIAL_7E2 0x2C
#define SERIAL_8E2 0x2E
#define SERIAL_7O1 0x34
#define SERIAL_8O1 0x36
#define SERIAL_7O2 0x3C
#define SERIAL_8O2 0x3E

class HardwareSerial : public Stream
{
  protected:
    // Has any byte been written to the UART since begin()
    bool _written;

    // Don't put any members after these buffers, since only the first
    // 32 bytes of this struct can be accessed quickly using the ldd
    // instruction.
    unsigned char _rx_buffer[SERIAL_RX_BUFFER_SIZE];
    unsigned char _tx_buffer[SERIAL_TX_BUFFER_SIZE];

    serial_t _serial;

  public:
    HardwareSerial(uint32_t _rx, uint32_t _tx);
    HardwareSerial(PinName _rx, PinName _tx);
    HardwareSerial(void* peripheral);
    void begin(unsigned long baud) { begin(baud, SERIAL_8N1); }
    void begin(unsigned long, uint8_t);
    void end();
    virtual int available(void);
    virtual int peek(void);
    virtual int read(void);
    int availableForWrite(void);
    virtual void flush(void);
    virtual size_t write(uint8_t);
    inline size_t write(unsigned long n) { return write((uint8_t)n); }
    inline size_t write(long n) { return write((uint8_t)n); }
    inline size_t write(unsigned int n) { return write((uint8_t)n); }
    inline size_t write(int n) { return write((uint8_t)n); }
    using Print::write; // pull in write(str) and write(buf, size) from Print
    operator bool() { return true; }

    void setRx(uint32_t _rx);
    void setTx(uint32_t _tx);
    void setRx(PinName _rx);
    void setTx(PinName _tx);

    friend class STM32LowPower;

    // Interrupt handlers
    static void _rx_complete_irq(serial_t* obj);
    static int _tx_complete_irq(serial_t* obj);
  private:
    uint8_t _config;
    void init(void);
    void configForLowPower(void);
};

extern HardwareSerial Serial1;
extern HardwareSerial Serial2;
extern HardwareSerial Serial3;
extern HardwareSerial Serial4;
extern HardwareSerial Serial5;
extern HardwareSerial Serial6;
extern HardwareSerial Serial7;
extern HardwareSerial Serial8;
extern HardwareSerial Serial9;
extern HardwareSerial Serial10;

extern void serialEventRun(void) __attribute__((weak));

#endif