Merge branch 'master' into master

Author: LusimiCollado

CMakeLists.txt

@@ -301,6 +301,7 @@ set(ARDUINO_LIBRARY_Zigbee_SRCS
   libraries/Zigbee/src/ep/ZigbeeWindSpeedSensor.cpp
   libraries/Zigbee/src/ep/ZigbeeIlluminanceSensor.cpp
   libraries/Zigbee/src/ep/ZigbeePM25Sensor.cpp
+  libraries/Zigbee/src/ep/ZigbeePowerOutlet.cpp
   )
 
 set(ARDUINO_LIBRARY_BLE_SRCS

libraries/ESP_SR/src/esp32-hal-sr.c

@@ -192,6 +192,7 @@ static void audio_feed_task(void *arg) {
 
     /* Feed samples of an audio stream to the AFE_SR */
     g_sr_data->afe_handle->feed(g_sr_data->afe_data, audio_buffer);
+    vTaskDelay(2);
   }
   vTaskDelete(NULL);
 }

libraries/Zigbee/examples/Zigbee_On_Off_MultiSwitch/README.md

@@ -0,0 +1,110 @@
+# Arduino-ESP32 Zigbee Multi-Switch Example
+
+This example demonstrates how to configure a Zigbee device as a multi-switch controller that can control up to three different Zigbee lights independently. The switch can operate in either coordinator or router mode, making it compatible with Home Assistant integration.
+
+# Supported Targets
+
+Currently, this example supports the following targets.
+
+| Supported Targets | ESP32-C6 | ESP32-H2 |
+| ----------------- | -------- | -------- |
+
+## Hardware Required
+
+* One development board (ESP32-H2 or ESP32-C6) acting as Zigbee multi-switch controller
+* One or more Zigbee light devices (loaded with Zigbee_On_Off_Light example)
+* A USB cable for power supply and programming
+
+### Configure the Project
+
+The example uses the BOOT button (pin 9) on ESP32-C6 and ESP32-H2 as the physical switch input. The switch can be configured to operate in two modes:
+
+1. **Coordinator Mode**: For running your own Zigbee network
+2. **Router Mode**: For Home Assistant integration
+
+#### Using Arduino IDE
+
+To get more information about the Espressif boards see [Espressif Development Kits](https://www.espressif.com/en/products/devkits).
+
+* Before Compile/Verify, select the correct board: `Tools -> Board`
+* Select the Zigbee mode: `Tools -> Zigbee mode: Zigbee ZCZR (coordinator/router)`
+* Select Partition Scheme for Zigbee: `Tools -> Partition Scheme: Zigbee 4MB with spiffs`
+* Select the COM port: `Tools -> Port: xxx` where the `xxx` is the detected COM port
+* Optional: Set debug level to verbose to see all logs from Zigbee stack: `Tools -> Core Debug Level: Verbose`
+
+## Features
+
+The multi-switch example provides the following functionality:
+
+1. **Light Configuration**
+   - Configure up to 3 different lights using their endpoint and IEEE address
+   - Configuration is stored in NVS (Non-Volatile Storage) and persists after power loss
+   - Remove configured lights when needed
+
+2. **Control Commands**
+   - Control all bound lights simultaneously:
+     - Turn all bound lights ON
+     - Turn all bound lights OFF
+     - Toggle all bound lights
+   - Control individual lights (1-3):
+     - Turn light ON
+     - Turn light OFF
+     - Toggle light
+
+3. **Network Management**
+   - Factory reset capability
+   - Open network for device joining
+   - View bound devices and current light configurations
+
+## Serial Commands
+
+The example accepts the following commands through the serial interface:
+
+* `config` - Configure a new light (requires light number, endpoint, and IEEE address)
+* `remove` - Remove a configured light
+* `on` - Turn all bound lights ON
+* `off` - Turn all bound lights OFF
+* `toggle` - Toggle all bound lights
+* `1on`, `2on`, `3on` - Turn individual light ON
+* `1off`, `2off`, `3off` - Turn individual light OFF
+* `1toggle`, `2toggle`, `3toggle` - Toggle individual light
+* `freset` - Perform factory reset
+* `open_network` - Open network for device joining (only for coordinator role)
+
+## Troubleshooting
+
+If the End device flashed with the example `Zigbee_On_Off_Light` is not connecting to the coordinator, erase the flash of the End device before flashing the example to the board. It is recommended to do this if you re-flash the coordinator.
+You can do the following:
+
+* In the Arduino IDE go to the Tools menu and set `Erase All Flash Before Sketch Upload` to `Enabled`
+* In the `Zigbee_On_Off_Light` example sketch call `Zigbee.factoryReset()`
+
+By default, the coordinator network is closed after rebooting or flashing new firmware.
+To open the network you have 2 options:
+
+* Open network after reboot by setting `Zigbee.setRebootOpenNetwork(time)` before calling `Zigbee.begin()`
+* In application you can anytime call `Zigbee.openNetwork(time)` to open the network for devices to join
+
+***Important: Make sure you are using a good quality USB cable and that you have a reliable power source***
+
+* **LED not blinking:** Check the wiring connection and the IO selection
+* **Programming Fail:** If the programming/flash procedure fails, try reducing the serial connection speed
+* **COM port not detected:** Check the USB cable and the USB to Serial driver installation
+
+If the error persists, you can ask for help at the official [ESP32 forum](https://esp32.com) or see [Contribute](#contribute).
+
+## Contribute
+
+To know how to contribute to this project, see [How to contribute.](https://github.com/espressif/arduino-esp32/blob/master/CONTRIBUTING.rst)
+
+If you have any **feedback** or **issue** to report on this example/library, please open an issue or fix it by creating a new PR. Contributions are more than welcome!
+
+Before creating a new issue, be sure to try Troubleshooting and check if the same issue was already created by someone else.
+
+## Resources
+
+* Official ESP32 Forum: [Link](https://esp32.com)
+* Arduino-ESP32 Official Repository: [espressif/arduino-esp32](https://github.com/espressif/arduino-esp32)
+* ESP32-C6 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32-c6_datasheet_en.pdf)
+* ESP32-H2 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32-h2_datasheet_en.pdf)
+* Official ESP-IDF documentation: [ESP-IDF](https://idf.espressif.com)