esp32-hal-uart.c

// Copyright 2015-2024 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at

//     http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.

#include "esp32-hal.h"

#include "freertos/FreeRTOS.h"
#include "freertos/semphr.h"

#include "driver/uart.h"
#include "hal/uart_ll.h"
#include "soc/soc_caps.h"
#include "soc/uart_struct.h"
#include "soc/uart_periph.h"
#include "rom/ets_sys.h"
#include "rom/gpio.h"

#include "driver/gpio.h"
#include "hal/gpio_hal.h"
#include "esp_rom_gpio.h"

static int s_uart_debug_nr = 0;               // UART number for debug output

struct uart_struct_t {

#if !CONFIG_DISABLE_HAL_LOCKS
    SemaphoreHandle_t lock;                   // UART lock
#endif

    uint8_t num;                               // UART number for IDF driver API
    bool has_peek;                             // flag to indicate that there is a peek byte pending to be read
    uint8_t peek_byte;                         // peek byte that has been read but not consumed
    QueueHandle_t uart_event_queue;            // export it by some uartGetEventQueue() function
    // configuration data:: Arduino API tipical data
    int8_t _rxPin, _txPin, _ctsPin, _rtsPin;   // UART GPIOs
    uint32_t _baudrate, _config;               // UART baudrate and config
    // UART ESP32 specific data
    uint16_t _rx_buffer_size, _tx_buffer_size; // UART RX and TX buffer sizes
    bool _inverted;                            // UART inverted signal
    uint8_t _rxfifo_full_thrhd;                // UART RX FIFO full threshold
};

#if CONFIG_DISABLE_HAL_LOCKS

#define UART_MUTEX_LOCK()
#define UART_MUTEX_UNLOCK()

static uart_t _uart_bus_array[] = {
    {0, false, 0, NULL, -1, -1, -1, -1, 0, 0, 0, 0, false, 0},
#if SOC_UART_NUM > 1
    {1, false, 0, NULL, -1, -1, -1, -1, 0, 0, 0, 0, false, 0},
#endif
#if SOC_UART_NUM > 2
    {2, false, 0, NULL, -1, -1, -1, -1, 0, 0, 0, 0, false, 0},
#endif
};

#else

#define UART_MUTEX_LOCK()    if(uart->lock != NULL) do {} while (xSemaphoreTake(uart->lock, portMAX_DELAY) != pdPASS)
#define UART_MUTEX_UNLOCK()  if(uart->lock != NULL) xSemaphoreGive(uart->lock)

static uart_t _uart_bus_array[] = {
    {NULL, 0, false, 0, NULL, -1, -1, -1, -1, 0, 0, 0, 0, false, 0},
#if SOC_UART_NUM > 1
    {NULL, 1, false, 0, NULL, -1, -1, -1, -1, 0, 0, 0, 0, false, 0},
#endif
#if SOC_UART_NUM > 2
    {NULL, 2, false, 0, NULL, -1, -1, -1, -1, 0, 0, 0, 0, false, 0},
#endif
};

#endif

// Negative Pin Number will keep it unmodified, thus this function can detach individual pins
// This function will set the pin to -1 after detaching
static bool _uartDetachPins(uint8_t uart_num, int8_t rxPin, int8_t txPin, int8_t ctsPin, int8_t rtsPin)
{
    if(uart_num >= SOC_UART_NUM) {
        log_e("Serial number is invalid, please use number from 0 to %u", SOC_UART_NUM - 1);
        return false;
    }
    // get UART information
    uart_t* uart = &_uart_bus_array[uart_num];
    bool retCode = true;
    //log_v("detaching UART%d pins: prev,pin RX(%d,%d) TX(%d,%d) CTS(%d,%d) RTS(%d,%d)", uart_num, 
    //        uart->_rxPin, rxPin, uart->_txPin, txPin, uart->_ctsPin, ctsPin, uart->_rtsPin, rtsPin); vTaskDelay(10);

    // detaches pins and sets UART information
    if (rxPin >= 0 && uart->_rxPin == rxPin) {
        gpio_hal_iomux_func_sel(GPIO_PIN_MUX_REG[rxPin], PIN_FUNC_GPIO);
        // avoids causing BREAK in the UART line
        if (uart->_inverted) {
            esp_rom_gpio_connect_in_signal(GPIO_FUNC_IN_LOW, UART_PERIPH_SIGNAL(uart_num, SOC_UART_RX_PIN_IDX), false);
        } else {
            esp_rom_gpio_connect_in_signal(GPIO_FUNC_IN_HIGH, UART_PERIPH_SIGNAL(uart_num, SOC_UART_RX_PIN_IDX), false);
        }
        uart->_rxPin = -1;  // -1 means unassigned/detached
    }
    if (txPin >= 0 && uart->_txPin == txPin) {
        gpio_hal_iomux_func_sel(GPIO_PIN_MUX_REG[txPin], PIN_FUNC_GPIO);
        esp_rom_gpio_connect_out_signal(txPin, SIG_GPIO_OUT_IDX, false, false);
        uart->_txPin = -1;  // -1 means unassigned/detached
    }
    if (ctsPin >= 0 && uart->_ctsPin == ctsPin) {
        gpio_hal_iomux_func_sel(GPIO_PIN_MUX_REG[ctsPin], PIN_FUNC_GPIO);
        esp_rom_gpio_connect_in_signal(GPIO_FUNC_IN_LOW, UART_PERIPH_SIGNAL(uart_num, SOC_UART_CTS_PIN_IDX), false);
        uart->_ctsPin = -1;  // -1 means unassigned/detached
    }
    if (rtsPin >= 0 && uart->_rtsPin == rtsPin) {
        gpio_hal_iomux_func_sel(GPIO_PIN_MUX_REG[rtsPin], PIN_FUNC_GPIO);
        esp_rom_gpio_connect_out_signal(rtsPin, SIG_GPIO_OUT_IDX, false, false);
        uart->_rtsPin = -1;  // -1 means unassigned/detached
    }
    return retCode;
}

// Attach function for UART 
// connects the IO Pad, set internal UART structure data
static bool _uartAttachPins(uint8_t uart_num, int8_t rxPin, int8_t txPin, int8_t ctsPin, int8_t rtsPin)
{
    if(uart_num >= SOC_UART_NUM) {
        log_e("Serial number is invalid, please use number from 0 to %u", SOC_UART_NUM - 1);
        return false;
    }
    // get UART information
    uart_t* uart = &_uart_bus_array[uart_num];
    //log_v("attaching UART%d pins: prev,new RX(%d,%d) TX(%d,%d) CTS(%d,%d) RTS(%d,%d)", uart_num, 
    //        uart->_rxPin, rxPin, uart->_txPin, txPin, uart->_ctsPin, ctsPin, uart->_rtsPin, rtsPin); vTaskDelay(10);


    bool retCode = true;
    if (rxPin >= 0) {
        // connect RX Pad
        bool ret = ESP_OK == uart_set_pin(uart->num, UART_PIN_NO_CHANGE, rxPin, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE);
        if (ret) {
            uart->_rxPin = rxPin;
        } else {
            log_e("UART%d failed to attach RX pin %d", uart_num, rxPin);
        }
        retCode &= ret;
    }
    if (txPin >= 0) {
        // connect TX Pad
        bool ret = ESP_OK == uart_set_pin(uart->num, txPin, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE);
        if (ret) {
            if (ret) uart->_txPin = txPin;
        } else {
            log_e("UART%d failed to attach TX pin %d", uart_num, txPin);
        }
        retCode &= ret;
    }
    if (ctsPin >= 0) {
        // connect CTS Pad
        bool ret = ESP_OK == uart_set_pin(uart->num, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE, ctsPin);
        if (ret) {
            if (ret) uart->_ctsPin = ctsPin;
        } else {
            log_e("UART%d failed to attach CTS pin %d", uart_num, ctsPin);
        }
        retCode &= ret;
    }
    if (rtsPin >= 0) {
        // connect RTS Pad
        bool ret = ESP_OK == uart_set_pin(uart->num, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE, rtsPin, UART_PIN_NO_CHANGE);
        if (ret) {
            if (ret) uart->_rtsPin = rtsPin;
        } else {
            log_e("UART%d failed to attach RTS pin %d", uart_num, rtsPin);
        }
        retCode &= ret;
    }
    return retCode;
}

// just helper functions
int8_t uart_get_RxPin(uint8_t uart_num)
{
    return _uart_bus_array[uart_num]._rxPin;
}

int8_t uart_get_TxPin(uint8_t uart_num)
{
    return _uart_bus_array[uart_num]._txPin;
}

// solves issue https://github.com/espressif/arduino-esp32/issues/6032
// baudrate must be multiplied when CPU Frequency is lower than APB 80MHz
uint32_t _get_effective_baudrate(uint32_t baudrate) 
{
    uint32_t Freq = getApbFrequency()/1000000;
    if (Freq < 80) {
        return 80 / Freq * baudrate;
     }
    else {
        return baudrate;
    }
}

// Routines that take care of UART events will be in the HardwareSerial Class code
void uartGetEventQueue(uart_t* uart, QueueHandle_t *q)
{
    // passing back NULL for the Queue pointer when UART is not initialized yet
    *q = NULL;
    if(uart == NULL) {
        return;
    }
    *q = uart->uart_event_queue;
    return;
}

bool uartIsDriverInstalled(uart_t* uart) 
{
    if(uart == NULL) {
        return false;
    }

    if (uart_is_driver_installed(uart->num)) {
        return true;
    }
    return false;
}

// Negative Pin Number will keep it unmodified, thus this function can set individual pins
// When pins are changed, it will detach the previous one
bool uartSetPins(uint8_t uart_num, int8_t rxPin, int8_t txPin, int8_t ctsPin, int8_t rtsPin)
{
    if(uart_num >= SOC_UART_NUM) {
        log_e("Serial number is invalid, please use number from 0 to %u", SOC_UART_NUM - 1);
        return false;
    }
    // get UART information
    uart_t* uart = &_uart_bus_array[uart_num];

    bool retCode = true;
    UART_MUTEX_LOCK();

    //log_v("setting UART%d pins: prev->new RX(%d->%d) TX(%d->%d) CTS(%d->%d) RTS(%d->%d)", uart_num, 
    //        uart->_rxPin, rxPin, uart->_txPin, txPin, uart->_ctsPin, ctsPin, uart->_rtsPin, rtsPin); vTaskDelay(10);

    // First step: detachs all previous UART pins
    bool rxPinChanged = rxPin >= 0 && rxPin != uart->_rxPin;
    if (rxPinChanged) {
        retCode &= _uartDetachPins(uart_num, uart->_rxPin, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE);
    }
    bool txPinChanged = txPin >= 0 && txPin != uart->_txPin;
    if (txPinChanged) {
        retCode &= _uartDetachPins(uart_num, UART_PIN_NO_CHANGE, uart->_txPin, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE);
    }
    bool ctsPinChanged = ctsPin >= 0 && ctsPin != uart->_ctsPin;
    if (ctsPinChanged) {
        retCode &= _uartDetachPins(uart_num, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE, uart->_ctsPin, UART_PIN_NO_CHANGE);
    }
    bool rtsPinChanged = rtsPin >= 0 && rtsPin != uart->_rtsPin;
    if (rtsPinChanged) {
        retCode &= _uartDetachPins(uart_num, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE, uart->_rtsPin);
    }

    // Second step: attach all UART new pins
    if (rxPinChanged) {
        retCode &= _uartAttachPins(uart_num, rxPin, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE);
    }
    if (txPinChanged) {
        retCode &= _uartAttachPins(uart_num, UART_PIN_NO_CHANGE, txPin, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE);
    }
    if (ctsPinChanged) {
        retCode &= _uartAttachPins(uart->num, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE, ctsPin, UART_PIN_NO_CHANGE);
    }
    if (rtsPinChanged) {
        retCode &= _uartAttachPins(uart->num, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE, rtsPin);
    }
    UART_MUTEX_UNLOCK();  

    if (!retCode) {
        log_e("UART%d set pins failed.", uart_num);
    }
    return retCode;
}

// 
bool uartSetHwFlowCtrlMode(uart_t *uart, uart_hw_flowcontrol_t mode, uint8_t threshold) {
    if(uart == NULL) {
        return false;
    }
    // IDF will issue corresponding error message when mode or threshold are wrong and prevent crashing
    // IDF will check (mode > HW_FLOWCTRL_CTS_RTS || threshold >= SOC_UART_FIFO_LEN)
    UART_MUTEX_LOCK();
    bool retCode = (ESP_OK == uart_set_hw_flow_ctrl(uart->num, mode, threshold));
    UART_MUTEX_UNLOCK();  
    return retCode;
}

// This helper function will return true if a new IDF UART driver needs to be restarted and false if the current one can continue its execution
bool _testUartBegin(uint8_t uart_nr, uint32_t baudrate, uint32_t config, int8_t rxPin, int8_t txPin, uint32_t rx_buffer_size, uint32_t tx_buffer_size, bool inverted, uint8_t rxfifo_full_thrhd)
{
    if(uart_nr >= SOC_UART_NUM) {
        return false;  // no new driver has to be installed
    }
    uart_t* uart = &_uart_bus_array[uart_nr];
    // verify if it is necessary to restart the UART driver
    if (uart_is_driver_installed(uart_nr)) {
        // some parameters can't be changed unless we end the UART driver
        if ( uart->_rx_buffer_size != rx_buffer_size || uart->_tx_buffer_size != tx_buffer_size || uart->_inverted != inverted || uart->_rxfifo_full_thrhd != rxfifo_full_thrhd) {
            return true;   // the current IDF UART driver must be terminated and a new driver shall be installed
        } else {
            return false;  // The current IDF UART driver can continue its execution
        }
    } else {
        return true;       // no IDF UART driver is running and a new driver shall be installed
    }
}

uart_t* uartBegin(uint8_t uart_nr, uint32_t baudrate, uint32_t config, int8_t rxPin, int8_t txPin, uint32_t rx_buffer_size, uint32_t tx_buffer_size, bool inverted, uint8_t rxfifo_full_thrhd)
{
    if(uart_nr >= SOC_UART_NUM) {
        log_e("UART number is invalid, please use number from 0 to %u", SOC_UART_NUM - 1);
        return NULL;  // no new driver was installed
    }
    uart_t* uart = &_uart_bus_array[uart_nr];
    log_v("UART%d baud(%ld) Mode(%x) rxPin(%d) txPin(%d)", uart_nr, baudrate, config, rxPin, txPin);

#if !CONFIG_DISABLE_HAL_LOCKS
    if(uart->lock == NULL) {
        uart->lock = xSemaphoreCreateMutex();
        if(uart->lock == NULL) {
            log_e("Lock (Mutex) creation error.");
            return NULL; // no new driver was installed
        }
    }
#endif

    if (uart_is_driver_installed(uart_nr)) {
        log_v("UART%d Driver already installed.", uart_nr);
        // some parameters can't be changed unless we end the UART driver
        if ( uart->_rx_buffer_size != rx_buffer_size || uart->_tx_buffer_size != tx_buffer_size || uart->_inverted != inverted || uart->_rxfifo_full_thrhd != rxfifo_full_thrhd) {
            log_v("UART%d changing buffer sizes or inverted signal or rxfifo_full_thrhd. IDF driver will be restarted", uart_nr);
            uartEnd(uart_nr);
        } else {
            bool retCode = true;
            UART_MUTEX_LOCK();
            //User may just want to change some parameters, such as baudrate, data length, parity, stop bits or pins
            if (uart->_baudrate != baudrate) {
                if (ESP_OK != uart_set_baudrate(uart_nr, baudrate)) {
                    log_e("UART%d changing baudrate failed.", uart_nr);
                    retCode = false;
                } else {
                    log_v("UART%d changed baudrate to %d", uart_nr, baudrate);
                    uart->_baudrate = baudrate;
                }   
            }
            uart_word_length_t data_bits = (config & 0xc) >> 2;
            uart_parity_t parity = config & 0x3;
            uart_stop_bits_t stop_bits = (config & 0x30) >> 4;
            if (retCode && (uart->_config & 0xc) >> 2 != data_bits) {
                if (ESP_OK != uart_set_word_length(uart_nr, data_bits)) {
                    log_e("UART%d changing data length failed.", uart_nr);
                    retCode = false;
                } else {
                    log_v("UART%d changed data length to %d", uart_nr, data_bits + 5);
                }
            }
            if (retCode && (uart->_config & 0x3) != parity) {
                if (ESP_OK != uart_set_parity(uart_nr, parity)) {
                    log_e("UART%d changing parity failed.", uart_nr);
                    retCode = false;
                } else {
                    log_v("UART%d changed parity to %s", uart_nr, parity == 0 ? "NONE" : parity == 2 ? "EVEN" : "ODD");
                }                
            }
            if (retCode && (uart->_config & 0xc30) >> 4 != stop_bits) {
                if (ESP_OK != uart_set_stop_bits(uart_nr, stop_bits)) {
                    log_e("UART%d changing stop bits failed.", uart_nr);
                    retCode = false;
                } else {
                    log_v("UART%d changed stop bits to %d", uart_nr, stop_bits == 3 ? 2 : 1);
                }                
            }
            if (retCode) uart->_config = config;
            if (retCode && rxPin > 0 && uart->_rxPin != rxPin) {
                retCode &= _uartDetachPins(uart_nr, uart->_rxPin, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE);
                retCode &= _uartAttachPins(uart_nr, rxPin, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE);
                if (!retCode) {
                    log_e("UART%d changing RX pin failed.", uart_nr);
                } else {
                    log_v("UART%d changed RX pin to %d", uart_nr, rxPin);
                }
            }
            if (retCode && txPin > 0 && uart->_txPin != txPin) {
                retCode &= _uartDetachPins(uart_nr, UART_PIN_NO_CHANGE, uart->_txPin, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE);
                retCode &= _uartAttachPins(uart_nr, UART_PIN_NO_CHANGE, txPin, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE);
                if (!retCode) {
                    log_e("UART%d changing TX pin failed.", uart_nr);
                } else {
                    log_v("UART%d changed TX pin to %d", uart_nr, txPin);
                }   
            }
            UART_MUTEX_UNLOCK();
            if (retCode) {
                // UART driver was already working, just return the uart_t structure, saying that no new driver was installed
                return uart;
            }
            // if we reach this point, it means that we need to restart the UART driver
            uartEnd(uart_nr);
        }
    } else {
        log_v("UART%d not installed. Starting installation", uart_nr);
    }
    uart_config_t uart_config;
    uart_config.data_bits = (config & 0xc) >> 2;
    uart_config.parity = (config & 0x3);
    uart_config.stop_bits = (config & 0x30) >> 4;
    uart_config.flow_ctrl = UART_HW_FLOWCTRL_DISABLE;
    uart_config.rx_flow_ctrl_thresh = rxfifo_full_thrhd;
#if SOC_UART_SUPPORT_XTAL_CLK
    // works independently of APB frequency
    uart_config.source_clk = UART_SCLK_XTAL; // ESP32C3, ESP32S3
    uart_config.baud_rate = baudrate;
#else
    uart_config.source_clk = UART_SCLK_APB;  // ESP32, ESP32S2
    uart_config.baud_rate = _get_effective_baudrate(baudrate);
#endif
    UART_MUTEX_LOCK();
    bool retCode = ESP_OK == uart_driver_install(uart_nr, rx_buffer_size, tx_buffer_size, 20, &(uart->uart_event_queue), 0);

    if (retCode) retCode &= ESP_OK == uart_param_config(uart_nr, &uart_config);

    if (retCode) {
      if (inverted) {
        // invert signal for both Rx and Tx
        retCode &= ESP_OK == uart_set_line_inverse(uart_nr, UART_SIGNAL_TXD_INV | UART_SIGNAL_RXD_INV);
      } else {
        // invert signal for both Rx and Tx
        retCode &= ESP_OK == uart_set_line_inverse(uart_nr, UART_SIGNAL_INV_DISABLE);
      }
    }
    // if all fine, set internal parameters
    if (retCode) {
        uart->_baudrate = baudrate;
        uart->_config = config;
        uart->_inverted = inverted;
        uart->_rxfifo_full_thrhd = rxfifo_full_thrhd;
        uart->_rx_buffer_size = rx_buffer_size;
        uart->_tx_buffer_size = tx_buffer_size;
        uart->has_peek = false;
        uart->peek_byte = 0;
    }
    UART_MUTEX_UNLOCK();

    // uartSetPins detaches previous pins if new ones are used over a previous begin()
    if (retCode) retCode &= uartSetPins(uart_nr, rxPin, txPin, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE);
    if (!retCode) {
        uartEnd(uart_nr);
        uart = NULL;
        log_e("UART%d initialization error.", uart->num);
    } else {
        uartFlush(uart);
        log_v("UART%d initialization done.", uart->num);
    }
    return uart;  // a new driver was installed
}

// This function code is under testing - for now just keep it here
void uartSetFastReading(uart_t* uart)
{
    if(uart == NULL) {
        return;
    }

    UART_MUTEX_LOCK();
    // override default RX IDF Driver Interrupt - no BREAK, PARITY or OVERFLOW
    uart_intr_config_t uart_intr = {
        .intr_enable_mask = UART_INTR_RXFIFO_FULL | UART_INTR_RXFIFO_TOUT,   // only these IRQs - no BREAK, PARITY or OVERFLOW
        .rx_timeout_thresh = 1,
        .txfifo_empty_intr_thresh = 10,
        .rxfifo_full_thresh = 2,
    };

    ESP_ERROR_CHECK(uart_intr_config(uart->num, &uart_intr));
    UART_MUTEX_UNLOCK();
}


bool uartSetRxTimeout(uart_t* uart, uint8_t numSymbTimeout)
{
    if(uart == NULL) {
        return false;
    }

    UART_MUTEX_LOCK();
    bool retCode = (ESP_OK == uart_set_rx_timeout(uart->num, numSymbTimeout));
    UART_MUTEX_UNLOCK();
    return retCode;
}

bool uartSetRxFIFOFull(uart_t* uart, uint8_t numBytesFIFOFull)
{
    if(uart == NULL) {
        return false;
    }

    UART_MUTEX_LOCK();
    bool retCode = (ESP_OK == uart_set_rx_full_threshold(uart->num, numBytesFIFOFull));
    UART_MUTEX_UNLOCK();
    return retCode;
}


void uartEnd(uint8_t uart_num)
{
    if(uart_num >= SOC_UART_NUM) {
        log_e("Serial number is invalid, please use number from 0 to %u", SOC_UART_NUM - 1);
        return;
    }
    // get UART information
    uart_t* uart = &_uart_bus_array[uart_num];
   
    UART_MUTEX_LOCK();
    _uartDetachPins(uart_num, uart->_rxPin, uart->_txPin, uart->_ctsPin, uart->_rtsPin);
    if(uart_is_driver_installed(uart_num)) {
        uart_driver_delete(uart_num);
    }
    UART_MUTEX_UNLOCK();
}


void uartSetRxInvert(uart_t* uart, bool invert)
{
    if (uart == NULL)
        return;
#if 0
    // POTENTIAL ISSUE :: original code only set/reset rxd_inv bit 
    // IDF or LL set/reset the whole inv_mask!
    if (invert)
        ESP_ERROR_CHECK(uart_set_line_inverse(uart->num, UART_SIGNAL_RXD_INV));
    else
        ESP_ERROR_CHECK(uart_set_line_inverse(uart->num, UART_SIGNAL_INV_DISABLE));
    
#else
    // this implementation is better over IDF API because it only affects RXD
    // this is supported in ESP32, ESP32-S2 and ESP32-C3
    uart_dev_t *hw = UART_LL_GET_HW(uart->num);
    if (invert)
        hw->conf0.rxd_inv = 1;
    else
        hw->conf0.rxd_inv = 0;
#endif
}


uint32_t uartAvailable(uart_t* uart)
{

    if(uart == NULL) {
        return 0;
    }

    UART_MUTEX_LOCK();
    size_t available;
    uart_get_buffered_data_len(uart->num, &available);
    if (uart->has_peek) available++;
    UART_MUTEX_UNLOCK();
    return available;
}


uint32_t uartAvailableForWrite(uart_t* uart)
{
    if(uart == NULL) {
        return 0;
    }
    UART_MUTEX_LOCK();
    uint32_t available =  uart_ll_get_txfifo_len(UART_LL_GET_HW(uart->num));  
    size_t txRingBufferAvailable = 0;
    if (ESP_OK == uart_get_tx_buffer_free_size(uart->num, &txRingBufferAvailable)) {
        available = txRingBufferAvailable == 0 ? available : txRingBufferAvailable; 
    }
    UART_MUTEX_UNLOCK();
    return available;
}

size_t uartReadBytes(uart_t* uart, uint8_t *buffer, size_t size, uint32_t timeout_ms)
{
    if(uart == NULL || size == 0 || buffer == NULL) {
        return 0;
    }

    size_t bytes_read = 0;

    UART_MUTEX_LOCK();

    if (uart->has_peek) {
        uart->has_peek = false;
        *buffer++ = uart->peek_byte;
        size--;
        bytes_read = 1;
    }

    if (size > 0) {
       int len = uart_read_bytes(uart->num, buffer, size, pdMS_TO_TICKS(timeout_ms));
       if (len < 0) len = 0;  // error reading UART
       bytes_read += len;
    }

        
    UART_MUTEX_UNLOCK();
    return bytes_read;
}

// DEPRICATED but the original code will be kepts here as future reference when a final solution
// to the UART driver is defined in the use case of reading byte by byte from UART.
uint8_t uartRead(uart_t* uart)
{
    if(uart == NULL) {
        return 0;
    }
    uint8_t c = 0;

    UART_MUTEX_LOCK();

    if (uart->has_peek) {
      uart->has_peek = false;
      c = uart->peek_byte;
    } else {

        int len = uart_read_bytes(uart->num, &c, 1, 20 / portTICK_PERIOD_MS);
        if (len <= 0) { // includes negative return from IDF in case of error
            c  = 0;
        }
    }
    UART_MUTEX_UNLOCK();
    return c;
}


uint8_t uartPeek(uart_t* uart)
{
    if(uart == NULL) {
        return 0;
    }
    uint8_t c = 0;

    UART_MUTEX_LOCK();

    if (uart->has_peek) {
      c = uart->peek_byte;
    } else {
        int len = uart_read_bytes(uart->num, &c, 1, 20 / portTICK_PERIOD_MS);
        if (len <= 0) { // includes negative return from IDF in case of error
            c  = 0;
        } else {
            uart->has_peek = true;
            uart->peek_byte = c;
        }
    }
    UART_MUTEX_UNLOCK();
    return c;
}

void uartWrite(uart_t* uart, uint8_t c)
{
    if(uart == NULL) {
        return;
    }
    UART_MUTEX_LOCK();
    uart_write_bytes(uart->num, &c, 1);
    UART_MUTEX_UNLOCK();
}

void uartWriteBuf(uart_t* uart, const uint8_t * data, size_t len)
{
    if(uart == NULL || data == NULL || !len) {
        return;
    }

    UART_MUTEX_LOCK();
    uart_write_bytes(uart->num, data, len);
    UART_MUTEX_UNLOCK();
}

void uartFlush(uart_t* uart)
{
    uartFlushTxOnly(uart, true);
}

void uartFlushTxOnly(uart_t* uart, bool txOnly)
{
    if(uart == NULL) {
        return;
    }
    
    UART_MUTEX_LOCK();
    while(!uart_ll_is_tx_idle(UART_LL_GET_HW(uart->num)));

    if ( !txOnly ) {
        ESP_ERROR_CHECK(uart_flush_input(uart->num));
    }
    UART_MUTEX_UNLOCK();
}

void uartSetBaudRate(uart_t* uart, uint32_t baud_rate)
{
    if(uart == NULL) {
        return;
    }
    UART_MUTEX_LOCK();
#if CONFIG_IDF_TARGET_ESP32 || CONFIG_IDF_TARGET_ESP32S2
    uart_ll_set_baudrate(UART_LL_GET_HW(uart->num), _get_effective_baudrate(baud_rate));
#else
    uart_ll_set_baudrate(UART_LL_GET_HW(uart->num), baud_rate);
#endif
    uart->_baudrate = baud_rate;
    UART_MUTEX_UNLOCK();
}

uint32_t uartGetBaudRate(uart_t* uart)
{
    if(uart == NULL) {
        return 0;
    }

    UART_MUTEX_LOCK();
    uint32_t baud_rate = uart_ll_get_baudrate(UART_LL_GET_HW(uart->num));
#if CONFIG_IDF_TARGET_ESP32 || CONFIG_IDF_TARGET_ESP32S2
    uint32_t Freq = getApbFrequency()/1000000;
    if (Freq < 80) {
        baud_rate = baud_rate / (80 / Freq);
     }
#endif
    UART_MUTEX_UNLOCK();
    return baud_rate;
}

static void ARDUINO_ISR_ATTR uart0_write_char(char c)
{
    while (uart_ll_get_txfifo_len(&UART0) == 0);
    uart_ll_write_txfifo(&UART0, (const uint8_t *) &c, 1);
}

#if SOC_UART_NUM > 1
static void ARDUINO_ISR_ATTR uart1_write_char(char c)
{
    while (uart_ll_get_txfifo_len(&UART1) == 0);
    uart_ll_write_txfifo(&UART1, (const uint8_t *) &c, 1);
}
#endif

#if SOC_UART_NUM > 2
static void ARDUINO_ISR_ATTR uart2_write_char(char c)
{
    while (uart_ll_get_txfifo_len(&UART2) == 0);
    uart_ll_write_txfifo(&UART2, (const uint8_t *) &c, 1);
}
#endif

void uart_install_putc()
{
    switch(s_uart_debug_nr) {
    case 0:
        ets_install_putc1((void (*)(char)) &uart0_write_char);
        break;
#if SOC_UART_NUM > 1
    case 1:
        ets_install_putc1((void (*)(char)) &uart1_write_char);
        break;
#endif
#if SOC_UART_NUM > 2
    case 2:
        ets_install_putc1((void (*)(char)) &uart2_write_char);
        break;
#endif
    default:
        ets_install_putc1(NULL);
        break;
    }
    ets_install_putc2(NULL);
}

// Routines that take care of UART mode in the HardwareSerial Class code
// used to set UART_MODE_RS485_HALF_DUPLEX auto RTS for TXD for ESP32 chips
bool uartSetMode(uart_t *uart, uart_mode_t mode)
{
    if (uart == NULL || uart->num >= SOC_UART_NUM)
    {
        return false;
    }
    
    UART_MUTEX_LOCK();
    bool retCode = (ESP_OK == uart_set_mode(uart->num, mode));
    UART_MUTEX_UNLOCK();
    return retCode;
}

void uartSetDebug(uart_t* uart)
{
    if(uart == NULL || uart->num >= SOC_UART_NUM) {
        s_uart_debug_nr = -1;
    } else {
        s_uart_debug_nr = uart->num;
    }
    uart_install_putc();
}

int uartGetDebug()
{
    return s_uart_debug_nr;
}

int log_printfv(const char *format, va_list arg)
{
    static char loc_buf[64];
    char * temp = loc_buf;
    uint32_t len;
    va_list copy;
    va_copy(copy, arg);
    len = vsnprintf(NULL, 0, format, copy);
    va_end(copy);
    if(len >= sizeof(loc_buf)){
        temp = (char*)malloc(len+1);
        if(temp == NULL) {
            return 0;
        }
    }
/*
// This causes dead locks with logging in specific cases and also with C++ constructors that may send logs
#if !CONFIG_DISABLE_HAL_LOCKS
    if(s_uart_debug_nr != -1 && _uart_bus_array[s_uart_debug_nr].lock){
        xSemaphoreTake(_uart_bus_array[s_uart_debug_nr].lock, portMAX_DELAY);
    }
#endif
*/
    vsnprintf(temp, len+1, format, arg);
    ets_printf("%s", temp);
/*
// This causes dead locks with logging and also with constructors that may send logs
#if !CONFIG_DISABLE_HAL_LOCKS
    if(s_uart_debug_nr != -1 && _uart_bus_array[s_uart_debug_nr].lock){
        xSemaphoreGive(_uart_bus_array[s_uart_debug_nr].lock);
    }
#endif
*/
    if(len >= sizeof(loc_buf)){
        free(temp);
    }
    // flushes TX - try to assure that the log message is completely sent.
    if(s_uart_debug_nr != -1) while(!uart_ll_is_tx_idle(UART_LL_GET_HW(s_uart_debug_nr)));
    return len;
}

int log_printf(const char *format, ...)
{
    int len;
    va_list arg;
    va_start(arg, format);
    len = log_printfv(format, arg);
    va_end(arg);
    return len;
}


static void log_print_buf_line(const uint8_t *b, size_t len, size_t total_len){
    for(size_t i = 0; i<len; i++){
        log_printf("%s0x%02x,",i?" ":"", b[i]);
    }
    if(total_len > 16){
        for(size_t i = len; i<16; i++){
            log_printf("      ");
        }
        log_printf("    // ");
    } else {
        log_printf(" // ");
    }
    for(size_t i = 0; i<len; i++){
        log_printf("%c",((b[i] >= 0x20) && (b[i] < 0x80))?b[i]:'.');
    }
    log_printf("\n");
}

void log_print_buf(const uint8_t *b, size_t len){
    if(!len || !b){
        return;
    }
    for(size_t i = 0; i<len; i+=16){
        if(len > 16){
            log_printf("/* 0x%04X */ ", i);
        }
        log_print_buf_line(b+i, ((len-i)<16)?(len - i):16, len);
    }
}

/*
 * if enough pulses are detected return the minimum high pulse duration + minimum low pulse duration divided by two. 
 * In the case of S3 and C3 using XTAL as UART CLK SOURCE, one bit period = Negative Pulse Count + 1
 * This equals one bit period. If flag is true the function return inmediately, otherwise it waits for enough pulses.
 */
unsigned long uartBaudrateDetect(uart_t *uart, bool flg)
{
    if(uart == NULL) {
        return 0;
    }

    uart_dev_t *hw = UART_LL_GET_HW(uart->num);

    while(uart_ll_get_rxd_edge_cnt(hw) < 30) { // UART_PULSE_NUM(uart_num)
        if(flg) return 0;
        ets_delay_us(1000);
    }

    UART_MUTEX_LOCK();
#if CONFIG_IDF_TARGET_ESP32 || CONFIG_IDF_TARGET_ESP32S2
    unsigned long ret = ((uart_ll_get_low_pulse_cnt(hw) + uart_ll_get_high_pulse_cnt(hw)) >> 1);
#else
    unsigned long ret = uart_ll_get_neg_pulse_cnt(hw) + 1;
#endif
    UART_MUTEX_UNLOCK();

    return ret;
}


/*
 * To start detection of baud rate with the uart the auto_baud.en bit needs to be cleared and set. The bit period is 
 * detected calling uartBadrateDetect(). The raw baudrate is computed using the UART_CLK_FREQ. The raw baudrate is 
 * rounded to the closed real baudrate.
 * 
*/
void uartStartDetectBaudrate(uart_t *uart) {
    if(uart == NULL) {
        return;
    }

    uart_dev_t *hw = UART_LL_GET_HW(uart->num);
    uart_ll_set_autobaud_en(hw, false);
    uart_ll_set_autobaud_en(hw, true);
}
 
unsigned long uartDetectBaudrate(uart_t *uart)
{
    if(uart == NULL) {
        return 0;
    }

    static bool uartStateDetectingBaudrate = false;

    if(!uartStateDetectingBaudrate) {
        uartStartDetectBaudrate(uart);
        uartStateDetectingBaudrate = true;
    }

    unsigned long divisor = uartBaudrateDetect(uart, true);
    if (!divisor) {
        return 0;
    }

    uart_dev_t *hw = UART_LL_GET_HW(uart->num);
    uart_ll_set_autobaud_en(hw, false);

    uartStateDetectingBaudrate = false; // Initialize for the next round
    
#if CONFIG_IDF_TARGET_ESP32 || CONFIG_IDF_TARGET_ESP32S2
    unsigned long baudrate = getApbFrequency() / divisor;  // ESP32 and S2 APB Freq
#else
    unsigned long baudrate = (getXtalFrequencyMhz() * 1000000) / divisor;  // S3 and C3 XTAL Frequency
#endif
    
    static const unsigned long default_rates[] = {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 74880, 115200, 230400, 250000, 
                                                  256000, 460800, 500000, 921600, 1000000, 1843200, 2000000, 3686400};
    size_t i;
    for (i = 1; i < sizeof(default_rates) / sizeof(default_rates[0]) - 1; i++)	{ // find the nearest real baudrate
        if (baudrate <= default_rates[i]) {
            if (baudrate - default_rates[i - 1] < default_rates[i] - baudrate) i--;
            break;
        }
    }

    return default_rates[i];
}

/*
    These functions are for testing purpose only and can be used in Arduino Sketches
    Those are used in the UART examples
*/

/*
    This is intended to make an internal loopback connection using IOMUX
    The function uart_internal_loopback() shall be used right after Arduino Serial.begin(...)
    This code "replaces" the physical wiring for connecting TX <--> RX in a loopback
*/

// gets the right TX or RX SIGNAL, based on the UART number from gpio_sig_map.h
#if SOC_UART_NUM > 2
  #define UART_TX_SIGNAL(uartNumber) (uartNumber == UART_NUM_0 ? U0TXD_OUT_IDX : (uartNumber == UART_NUM_1 ? U1TXD_OUT_IDX : U2TXD_OUT_IDX))
  #define UART_RX_SIGNAL(uartNumber) (uartNumber == UART_NUM_0 ? U0RXD_IN_IDX : (uartNumber == UART_NUM_1 ? U1RXD_IN_IDX : U2RXD_IN_IDX))
#else
  #define UART_TX_SIGNAL(uartNumber) (uartNumber == UART_NUM_0 ? U0TXD_OUT_IDX : U1TXD_OUT_IDX)
  #define UART_RX_SIGNAL(uartNumber) (uartNumber == UART_NUM_0 ? U0RXD_IN_IDX : U1RXD_IN_IDX)
#endif
/*
   This function internally binds defined UARTs TX signal with defined RX pin of any UART (same or different).
   This creates a loop that lets us receive anything we send on the UART without external wires.
*/
void uart_internal_loopback(uint8_t uartNum, int8_t rxPin)
{
  if (uartNum > SOC_UART_NUM - 1 || !GPIO_IS_VALID_GPIO(rxPin)) return;
  esp_rom_gpio_connect_out_signal(rxPin, UART_TX_SIGNAL(uartNum), false, false);
}

/*
    This is intended to generate BREAK in an UART line
*/

// Forces a BREAK in the line based on SERIAL_8N1 configuration at any baud rate
void uart_send_break(uint8_t uartNum)
{
  uint32_t currentBaudrate = 0;
  uart_get_baudrate(uartNum, &currentBaudrate);
  // calculates 10 bits of breaks in microseconds for baudrates up to 500mbps
  // This is very sensetive timing... it works fine for SERIAL_8N1
  uint32_t breakTime = (uint32_t) (10.0 * (1000000.0 / currentBaudrate));
  uart_set_line_inverse(uartNum, UART_SIGNAL_TXD_INV);
  esp_rom_delay_us(breakTime);
  uart_set_line_inverse(uartNum, UART_SIGNAL_INV_DISABLE);
}

// Sends a buffer and at the end of the stream, it generates BREAK in the line
int uart_send_msg_with_break(uint8_t uartNum, uint8_t *msg, size_t msgSize)
{
  // 12 bits long BREAK for 8N1
  return uart_write_bytes_with_break(uartNum, (const void *)msg, msgSize, 12);
}