Kconfig.projbuild

menu "Arduino Configuration"

config ENABLE_ARDUINO_DEPENDS
    bool
    select LWIP_SO_RCVBUF
    select ETHERNET
    select WIFI_ENABLED
    select ESP32_PHY_CALIBRATION_AND_DATA_STORAGE
    select MEMMAP_SMP
    default "y"

config AUTOSTART_ARDUINO
    bool "Autostart Arduino setup and loop on boot"
    default "n"
    help
        Enabling this option will implement app_main and start Arduino.
        All you need to implement in your main.cpp is setup() and loop()
        and include Arduino.h
        If disabled, you can call initArduino() to run any preparations
        required by the framework

config DISABLE_HAL_LOCKS
    bool "Disable mutex locks for HAL"
    default "n"
    help
        Enabling this option will run all hardware abstraction without locks.
        While communication with external hardware will be faster, you need to
        make sure that there is no option to use the same bus from another thread
        or interrupt at the same time. Option is best used with Arduino enabled
        and code implemented only in setup/loop and Arduino callbacks

menu "Debug Log Configuration"
choice ARDUHAL_LOG_DEFAULT_LEVEL
    bool "Default log level"
    default ARDUHAL_LOG_DEFAULT_LEVEL_ERROR
    help
        Specify how much output to see in logs by default.

config ARDUHAL_LOG_DEFAULT_LEVEL_NONE
    bool "No output"
config ARDUHAL_LOG_DEFAULT_LEVEL_ERROR
    bool "Error"
config ARDUHAL_LOG_DEFAULT_LEVEL_WARN
    bool "Warning"
config ARDUHAL_LOG_DEFAULT_LEVEL_INFO
    bool "Info"
config ARDUHAL_LOG_DEFAULT_LEVEL_DEBUG
    bool "Debug"
config ARDUHAL_LOG_DEFAULT_LEVEL_VERBOSE
    bool "Verbose"
endchoice

config ARDUHAL_LOG_DEFAULT_LEVEL
    int
    default 0 if ARDUHAL_LOG_DEFAULT_LEVEL_NONE
    default 1 if ARDUHAL_LOG_DEFAULT_LEVEL_ERROR
    default 2 if ARDUHAL_LOG_DEFAULT_LEVEL_WARN
    default 3 if ARDUHAL_LOG_DEFAULT_LEVEL_INFO
    default 4 if ARDUHAL_LOG_DEFAULT_LEVEL_DEBUG
    default 5 if ARDUHAL_LOG_DEFAULT_LEVEL_VERBOSE

config ARDUHAL_LOG_COLORS
    bool "Use ANSI terminal colors in log output"
    default "n"
    help
        Enable ANSI terminal color codes in bootloader output.
        In order to view these, your terminal program must support ANSI color codes.

config ARDUHAL_ESP_LOG
    bool "Forward ESP_LOGx to Arduino log output"
    default "n"
    help
        This option will redefine the ESP_LOGx macros to Arduino's log_x macros.
        To enable for your application, add the follwing after your includes:
        #ifdef ARDUINO_ARCH_ESP32
        #include "esp32-hal-log.h"
        #endif

endmenu

choice ARDUHAL_PARTITION_SCHEME
    bool "Used partition scheme"
    default ARDUHAL_PARTITION_SCHEME_DEFAULT
    help
        Specify which partition scheme to be used.

config ARDUHAL_PARTITION_SCHEME_DEFAULT
    bool "Default"
config ARDUHAL_PARTITION_SCHEME_MINIMAL
    bool "Minimal (for 2MB FLASH)"
config ARDUHAL_PARTITION_SCHEME_NO_OTA
    bool "No OTA (for large apps)"
config ARDUHAL_PARTITION_SCHEME_MIN_SPIFFS
    bool "Minimal SPIFFS (for large apps with OTA)"
endchoice

config ARDUHAL_PARTITION_SCHEME
    string
    default "default" if ARDUHAL_PARTITION_SCHEME_DEFAULT
    default "minimal" if ARDUHAL_PARTITION_SCHEME_MINIMAL
    default "no_ota" if ARDUHAL_PARTITION_SCHEME_NO_OTA
    default "min_spiffs" if ARDUHAL_PARTITION_SCHEME_MIN_SPIFFS


config AUTOCONNECT_WIFI
    bool "Autoconnect WiFi on boot"
    default "n"
    depends on AUTOSTART_ARDUINO
    help
        If enabled, WiFi will connect to the last used SSID (if station was enabled),
        else connection will be started only after calling WiFi.begin(ssid, password)

endmenu